Table of Contents
Related Manuals for Qomo QIT1386
Summary of Contents for Qomo QIT1386
- Page 1 QOMO Interactive Touch Screen QIT1386 User Manual Please properly keep the manual for further reference. This is the general user manual for all interactive touch screens. Therefore, it may be different from the actual product.
- Page 2 Welcome: Thanks for purchasing this product. Please read the instructions carefully before using this product. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
-
Page 3: Table Of Contents
Content Safety Instruction ............................1 Installation ..............................3 Introduction ..............................6 Basic Operation ............................7 Power on ..............................7 Power off ..............................7 OPS Installation ............................8 Remote Control ............................9 Functions of remote control ........................9 Instructions of remote control ........................ 10 Buttons &... -
Page 4: Safety Instruction
Safety Instruction For your safety, please read the following instruction before you use the product. Serious injury or property loss may be caused by improper operations. Do not try to repair the product by your own. WARNING Disconnect the product from power supply immediately if major failures occur. The major failures include the following: ... - Page 5 Use the specified power supply. ● Do not use any types of power cables other than the one provided with the product to prevent the product from being damaged. ● Use a three-wire socket and ensure that it is properly grounded. ●...
-
Page 6: Installation
Do not install the product in high temperature environments. Do not install the product near heat source, such as the radiator, the heat reservoir, the ● stove or other heating devices. Do not expose the product under sunlight, which may cause high temperature and ●... - Page 7 decoration layer, take necessary consolidating measures to ensure that the product is stably installed. Ventilation Ventilation Distance to the surface for installation (cm) requirements Left and right sides Bottom Back Nominal power Greater than 100 W If the product is installed inside a wall or a cabinet, in addition to the preceding requirements, the ventilation area around the bottom, top and two sides must be at least 50% of the sealing surface to ensure proper ventilation.
- Page 8 Installation diagram Level Insert wall plugs into the mounting holes. Use a level to locate the holes in Push the self-tapping screws through the horizontal line and mark with pencil bracket into the wall plugs and tighten the where the holes will be located. Then screws.
-
Page 9: Introduction
Introduction As our latest independently developed and produced human-machine interactive product, the Journey 13 series interactive touch screen is a multi-functional display for interactive teaching, digital demonstration, multi-media presentation, touch operations and handwriting. They are well designed and produced to meet the needs of education and corporate applications, and provide a user-friendly experience, digital intelligent control as an ideal equipment for schools and companies. -
Page 10: Basic Operation
Basic Operation Power on Power the interactive touch screen with the 100V-240V 50Hz/60Hz AC power supply. Connect the panel to the power supply. Switch on the rocker switch (on the left bottom of the rear of the panel, next to the power port) to enter standby status. The power indicator turns red. ... -
Page 11: Ops Installation
OPS Installation The OPS does not support hot-plugging. Please insert the plug of the OPS after the interactive panel is disconnected from the power. Install the OPS by following the following steps: Step 1: Insert the OPS into the special slot on the rear of the interactive panel. Step 2: Tighten the screws. -
Page 12: Remote Control
Remote Control Functions of remote control 1. Power on or standby 2. Mute 3. Change channels or enter numbers 4. Return 5. P. MODE: Picture mode SMODE: Sound mode 6. Signal source selection 7. Show the current signal source 8. VOL+/ VOL-: Increase/decrease volume 9. -
Page 13: Instructions Of Remote Control
Instructions of remote control The usage scope of the remote control includes the vertical distance within five meters in front of the panel, and the area within an angle of 30 degrees from the vertical point to the left and right. The effective receiving area is about 3 meters with 30°... -
Page 14: Buttons & Ports
Buttons & Ports Buttons & ports on the front panel Power indicator: Press power switch on the control Enter/Return to Android home page panel. The power indicator turns green. Press power switch on the control Return to previous interface panel to enter the standby status. -
Page 15: Ports On The Rear Panel For 65" & 75
Ports on the rear panel for 65” & 75” Ports on bottom of mainboard Ports on side of mainboard Ports on the rear panel for 86” Ports on side of mainboard Ports on bottom of mainboard... -
Page 16: Rs232 Code List
RS232 code list There are two RS232 code lists. Please refer to corresponding list according to your panel model. RS232 Code List for 65” & 75” 6 bytes command Baud rate: 115200 Data bits: 8 Check bit: none Start code 99, Customer code (Public Version: XX = 23),... - Page 17 Menu Signal Source Exit Listen only audio Volume + Volume - Channel + Channel - Screenshot Screen Display Display ratio Sleep Mode Auto Adjustment Down Left Right Confirm Multi-media Device Status Query 1. Status Query Feedback 8 byte data Start code 99, Board card model, Power On, Current...
- Page 18 Boar card model 2. Power on: Current channel: Computer 1 = 0B, Computer 2 = 0C, Computer 3 = 0D, Computer 4 = 06, ATV = 07, DTV = 05, Video = 08, Aberration = 0A, HDMI1 = 0E, HDMI2 = 0F, DP= 09, Front computer = 10, Built-in computer = 11, Multi-media or Application state of third party = 0E Volume: 0~100 (decimal) = 0~64 （hexadecimal）...
- Page 19 (4:3) Set Display Mode 0x64 0x30 0x21 0x21 0x55 0x54 0x53 0x50 (Figure Mode) 0x64 0x31 0x21 0x21 Set Display Mode 0x55 0x54 0x53 0x50 (Full View Mode) Set Display 0x64 0x32 0x21 0x21 0x55 0x54 0x53 0x50 Mode(Subtitle Mode) 0x64 0x33 0x21...
-
Page 20: Operation Interface
Operation Interface Android Home Page Android home page provides preview function that displays three parts. Click on the toolbar or Press HOME button to enter the home page. 1. Click the signal source in part ① and its thumbnail will be shown in part ②. Then click part ② to enter its corresponding signal source. - Page 21 Browser: Built-in browser. Applications: Click the icon to access more applications interface. Explorer: Click the icon to manage the file.
-
Page 22: Android Settings
Android Settings Click icon on home page or on bottom-up toolbar or press Setting button on the front panel to enter Android setting interface. Common function, Network and equipment, Storage, Language & input, Date & time and About are displayed on the interface. Press on the remote control or click the item directly to select the one you want to change its setting. - Page 23 6) Factory data reset Click Factory data reset and then click Reset TV to erase all the data on TV. Network and equipment Click Network and equipment to set WLAN, Ethernet, Tethering& portable hotspot and Mcast. 1) WLAN Select an available wireless network AP and enter the password to be connected. Click and a menu pops up.
- Page 24 If the panel is connected with LAN cable and supports Dynamic Host Configuration Protocol (DHCP), the system will automatically configure the internet protocol (IP) value. If the network protocol needs to be set manually, enter the IP address, Gateway and DNS server parameters by using the on-screen keyboard or remote control.
- Page 25 Click Portable WLAN hotspot to set the panel as a wifi hotspot or click Set WLAN hotspot to set related WIFI hotspot attributes in the displayed window. 3. Storage Click Storage to check internal storage and USB storage. Click Storage>Apps to check and manage the applications installed in Android system.
- Page 26 4. Apps Check all Apps installed and running in Android system. Click corresponding app to uninstall or stop it. Note: You can’t uninstall app pre-installed in the firmware. 5. Language & input...
- Page 27 6. Date & time Click Date & Time to change time format, time zone and etc. 7. About Click About to check network status, model, Android version, Kernel version and etc. Click Status and enter its page to get the Mac address.
-
Page 28: Built-In Pc Interface
Built-in PC Interface 1. Select PC signal source to enter PC interface. The following are three ways to select a signal source channel. Swipe your finger up from the bottom edge to bring up a toolbar then click input. ... -
Page 29: Bottom-Up Toolbar
Click an icon to set the option or press button on remote control to switch the options. Press▲/▼ button to select. Press OK button to confirm the selection. Press menu button to return to the parent menu. Press EXIT button to quit. -
Page 30: Annotation Software - Magicboard
Annotation software - MagicBoard MagicBoard provides various functions like annotation, capture, quick-access Apps & Docs and etc. Click icon to enter whiteboard interface. And click icon to fold/unfold the toolbar. MagicBoard Interface Icons Functions Click to exit the program or Select to keep it running in the background Click “<”... - Page 31 1. Save file Click icon to save the file. Check “Save to editable file” box so that you can reedit this file next time. You can open this editable file through DOC of File Management Or you can save the file in PDF format and scan QR code to share the file. Note that you mobile device should be in the same network with Magicboard.
- Page 32 3. Whiteboard running in the background Click icon then click “Background” and the whiteboard will run in the background. Icon will appear on both sides. Click either of them to unfold the tools. Note that floating icons will float in every singal source for annotation. Floating Tool Bar Buttons Functions...
- Page 33 Quick access files Annotation mode Save annotation as an image or scan QR code to share the annotation Enter the whiteboard Rectangular screenshot Window Shade Adjust volume...
-
Page 34: Included Accessories
Included Accessories Picture Name Quantity Remote control Battery (AAA) Pointer 1.8m power cable 3m HDMI cable 3m USB cable (A-B) Bracket Antenna sticks for PC and Android Warranty card... -
Page 35: Troubleshooting
Troubleshooting Problem Cause Solution The service program fails The driver program isn't properly Install the driver program to be connected. installed. properly. The USB port (lead) is not Change the USB lead or check if connected or is faulty. the USB port is faulty. Infrared tube is obscured. - Page 36 obscured. Strong light or infrared Remove the interference source interference exists. or change the using environment. The handwriting can’t be The color of the pen is the same Change the color of the pen. displayed. as or similar to the background color.
- Page 37 866-990-QOMO | 46950 Magelan Dr, Wixom, MI 48393 | info@qomo.com /qomosolutions Copyright ©2016 Qomo. All rights reserved. This document may not be copied in any form without permission from Qomo. Information in this document is subject to change without notice.