Sharp PN-V601 Operation Manual page 10

Menu Items
nAUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
Select "ON" and then press
nSETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
SCREEN MOTION
Residual images are reduced by moving the screen.
PATTERN1 ..... The whole screen moves vertically and
horizontally.
PATTERN2 ..... A black screen spreads from the bottom of
the screen and then shrinks to the bottom of
the screen.
If the monitor is installed in the vertical
orientation, a black screen spreads from the
left end of the screen and then shrinks to the
left end of the screen.
PATTERN3 ..... A black bar moves from the left end to the
right end of the screen.
If the monitor is installed in the vertical
orientation, a black bar moves from the top
to the bottom of the screen.
PATTERN4 ..... Black screens appear from both the top and
bottom of the screen, and the displayed
image is compressed into the central field.
If the monitor is installed in the vertical
orientation, the screen is compressed from
the left and right ends.
PATTERN1
PATTERN3
MOTION TIME 1
Specify a time period (operating interval) until SCREEN
MOTION starts.
MOTION TIME 2
Specify a time period during which SCREEN MOTION
operates (time period during which the screen will move).
MONITOR
Select the installation direction of the monitor.
LANDSCAPE ............Horizontal orientation
PORTRAIT ...............Vertical orientation
LANGUAGE
Sets the display language for the menu screen.
10
E
MENU
.
PATTERN2
PATTERN4
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second. When this function is activated, the power LED
flashes (at approx. 1 second interval) in orange. This function
is disabled when 0 is specified.
STANDBY MODE
When STANDARD is selected, startup time from standby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
When LOW POWER is selected, current consumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer.
If set to LOW POWER, certain RS-232C commands cannot
be used in standby mode, and control via LAN will be
disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into
standby mode when there is no operation from the remote
control unit, RS-232C commands, or LAN for over 4 hours.
HDMI SETTING
HDMI AUTO VIEW
......................... When ON is selected, the screen size is
adjusted automatically according to the
screen size control signal included in the
video signal input from the AV HDMI input
terminal.
HDMI RGB INPUT RANGE
......................... Sets the type of HDMI signals when using
the AV HDMI input mode.
When AUTO is selected, the type is set
automatically.
HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI
and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain
(see page 18), using the remote control unit or RS-232
cables.
The numbers 1 to 255 are available for ID numbers.
If "0" is set, the system regards this as the state where no ID
number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when
multiple monitors are connected with RS-232C.
MENU
Select ON, then press . Perform operations with the
primary monitor.
BAUD RATE
Selects the communication speed used for RS-232C
communication.
LAN SETUP
Configures the settings to control the monitor from the
computer via LAN. (See page 28.)