Altronix NetWay1 Installation Manual page 2

Fig. 1
Fig. 1a
www.altronix.com
www.altronix.com
NetWay1
Single Port Injector (Midspan)
24VAC/VDC, 1.2A Input
48VDC 15.4W max. per IEEE 802.3af
NetWay1
Equipment 92R2
Single Port Injector (Midspan) Access Control PoE Injector
I
Attack Class
General Signaling
24VAC/VDC, 1.2A Input
Equipment 92R2
48VDC 15.4W max. per IEEE 802.3af
I.T.E. 43KC
Equipment 92R2
24VAC/VDC
Access Control PoE Injector
Input IN
Attack Class
Installing a NetWay1512 adapter for 12VDC IP cameras up to 13W:
1. Mount NetWay1512 in proximity of IP camera (Fig. 3, pg. 3). Use velcro (supplied).
General Signaling
2. Connect structured cable from port marked [IN] on NetWay1512 to port marked [OUT] of NetWay1
Equipment 92R2
(Fig. 3, pg. 3, Fig. 1b pg. 2).
3. Connect structured cable from port marked [OUT] on NetWay1512 to the IP camera/device (Fig. 3, pg. 3, Fig. 1b pg. 2).
4. Connect 12VDC output from NetWay1512 terminals marked [---12VDC +] to the power input of the
I.T.E. 43KC
IP camera (Fig. 3, pg. 3). Polarity must be observed.
5. Power LED indicator will illuminate on NetWay1512 under normal conditions (Fig. 3, pg. 3).
Port Status
Non-Powered Device 0 <
24VAC/VDC
Input
PORT > 1M
R
Port Open
Port On 25k
Low Signature Resistance 300 <
High Signature Resistance 33K <
Port Overload Fault
Installing NetWayXT repeater module:
1. Mount NetWayXT in desired location utilizing the mounting hole (Fig. 4, pg. 3). Use a proper fastener and/or wall
anchor when securing NetWayXT to the wall.
2. Connect structured cable from port marked [OUT] on NetWay1 to port marked [IN] on the
NetWayXT (Fig. 4, pg. 3, Fig. 1b pg. 2).
3. Connect structured cable from port marked [OUT] on NetWayXT to the PoE camera/device or next NetWayXT
repeater (Fig. 4, pg. 3).
4. Port status LEDs will illuminate on NetWayXT indicating the port is operational (Fig. 4, pg. 3,
refer to Port LED definitions on pg. 2).
5. Power LED will illuminate indicating 12VDC output (Fig. 4, pg. 3).
Port LED definitions for NetWayXT repeater:
Status
OFF Indicates it is connected as 10Base-T or no link.
ON Indicates it is connected as 100Base-T.
Blinking
- 2 -
24VAC/
24VDC Input
Port
Status
Power
OUT Shutdown
I
NetWay1 Port Status and LED Flash Codes
PORT < 200
IN R OUT
PORT < 15k
R
PORT < 500k
R
Green LED
-------
Fig. 1b
Structured
Cable from
Network
Switch
Structured Cable from
IP Camera, IP Lock or IP device,
NetWay1512 or NetWayXT
Fig. 1c
Port
Status
Flash Code
Power
Shutdown
OFF
OFF
ON
5
1 Flash
5 5
2 Flashes
5 Flashes
Indicates no link.
Indicates a link.
Indicates activity.
12VAC to 24VAC or
5VDC to 24VDC Input
for PoE shutdown
24VAC/
24VDC Input
Flash Pattern
LED OFF
LED OFF
LED ON
5
5 5
5 5 5 5 5
Yellow LED
Structur
Cable fr
Netwo
Switc
Struc
IP Camera
NetWay
5
5 5
NetWay1