Table of Contents
Advertisement
GRAPHIC SYMBOL EXPLANATION
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the unit.
1. Read Instructions - All the safety and operating
instructions should be read before the video product is
operated.
2. Retain Instructions - All the safety and operating
instructions should be retained for future reference.
3. Heed Warnings - All warnings on the video product and
in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Step a applies to equipment that can be
disconnected from the CCTV system without seriously
jeopardizing security. Step b applies to equipment that
must operate continuously such as video switching
equipment at military installations.
a.
Disconnect this video product from its power
source before cleaning. Do not use caustic,
abrasive, or aerosol cleaners. Use a damp cloth
for cleaning.
b.
Use a damp cloth to clean the equipment. Do not
allow moisture or liquids to enter any vents. Do
not use caustic, abrasive, or aerosol cleaners.
6. Attachments - Do not use attachments not
recommended by UNITED VISION as they may cause
hazards.
7. Accessories - Do not place this video product on any
unstable surface or table. The video product may fall,
causing serious injury to a person and serious damage to
the video product. Use only with a mounting accessory
recommended by UNITED VISION, or sold with the video
product. Any mounting of the video product should follow
UNITED VISION's instructions, and a mounting accessory
recommended by UNITED VISION should be used.
8. Power Sources - This video product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supplied to your installation site, consult your UNITED
VISION dealer or local power company. For video products
intended to operate from battery power, or other sources,
refer to the operating instructions.
9. Power-Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the video
product.
10. Outdoor Cable Grounding - If an outside cable system
is connected to the video product, be sure the cable
system is grounded so as to provide some protection
against voltage surges and built-up static charges.
11. Lightning - For added protection for this video
product when it is not used for long periods of time,
disconnect it from its power source and from the cable
system. This prevents damage to the video product due to
lightning and power-line surges.
12. Power Lines - An outside cable system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
cable system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
13. Overloading - Do not overload wall outlets and
extension cords as this can result in a risk of fire or
electric shock.
14. Object and Liquid Entry - Never push objects of any
kind into this video product through openings as they may
touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the video product.
15. Servicing - Do not attempt to service this video
product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
16. Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by UNITED VISION or that
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
17. Safety Check - Upon completion of any service or
repairs to this video product, ask the service technician to
perform safety checks to determine that the video
product is in proper operating condition.
Advertisement
Table of Contents
