Johnson Controls M9106-AGx-2N0x Series Installation Instructions

m910-26
M9106-AGx-2N0x Series
Electric Non-spring Return Actuators
m9106-2n.tif
M9106-AGS-2N02
Description
The M9106-AGA-2N0x synchronous
motor-driven actuators provide floating
(3-wire) control and are easily installed on a
Variable Air Volume (VAV) box. They may
also be installed on a small or medium-sized
damper with a round shaft up to 1/2 inch
(13 mm) in diameter or a 3/8 inch (10 mm)
square shaft.
These compact, non-spring return actuators
have 53 lb·in (6 N·m) running torque in a
compact easy-to-install package. The
actuators are available with either a nominal
Accessories
Code Number
20 in. (0.5 m) wiring harness, UL accepted for plenum use, supplied with the
CBL-2000-1 M9106-AGS-2N02 and may be ordered separately; connects the M9106 and
DPT-2015 to the VAV controller
CBL-2000-2 20 in. (0.5 m) plenum-rated wiring harness
CBL-2000-3 72 in. (1.8 m) plenum-rated wiring harness
0 to 1.5 in. W.C. (0 to 375 Pa) differential pressure transmitter supplied with the
DPT-2015-0
M9106-AGS-2N02 and may be ordered separately
Blade Pin Extension without bracket supplied with Johnson Controls
DMPR-KC003
CD-1300 dampers and may be ordered separately
Sleeve Pin Kit supplied with Johnson Controls round dampers that have a 5/16 in.
DMPR-KR003
(8 mm) shaft and may be ordered separately
Adjustable Blade Position Indicator Switch Kit with total switching load limited to
2000 VA for the following applications:
Pilot Duty: 24 VAC, 50 VA; 125/250/277 VAC, 125 VA
(a)
DMPR-KC010
Motor Load: 125/250/277 VAC, 1/3 hp
Resistive Load: 125 VAC, 11 A; 250 VAC, 8 A; 277 VAC, 7 A
(all maximum values)
Commissioning Tool provides a control signal to drive on/off, floating,
M9000-200
proportional, or resistive actuators.
(a) Use with an M9106 actuator to replace an EDA-2040 or ATP-2040 actuator and
EDA-2040-102 switch kit.
The performance specifications are nominal and conform to acceptable industry standards. For applications at conditions beyond t hese specifications, consult the local Johnson
Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products.
1900119 9thcc:na Electronics
60-second travel time at 60 Hz (72 seconds at
50 Hz) or a nominal 120-second travel time at
60 Hz (144 seconds at 50 Hz) for 90° of
rotation.
The M9106-AGS-2N02 Actuator/Transmitter
combines an M9106-AGA-2N02 with a
prewired DPT-2015 Differential Pressure
Transmitter that has a 0 to 1.5 in. W.C.
(0 to 374 Pa) differential pressure range.
Features
• 35 dBA rating meets audible requirements
for open ceilings
• synchronous drive provides constant
rotation time that is independent of load
• direct shaft mount with single-screw
coupler simplifies installation and provides
3-point shaft gripping
• magnetic clutch provides torque protection
for the actuator and damper
• adjustable rotation stops allow application
versatility with 30 to 90° clockwise or
counterclockwise rotation
• manual gear release simplifies setup and
field adjustments
• screw terminal connection makes wiring
easy
Description
1/2
Controls Group 507 E. Michigan Street
P.O. Box 423, Milwaukee, WI 53202
Code No. LIT-1900119
Actuators
Applications
The actuators are used to position balancing,
control, round, and zone dampers in typical
HVAC applications. They are also used to
position the blades in a VAV box. The
actuators mount directly to the surface of a
VAV box, round damper, or small rectangular
damper with a single No. 10 self-drilling sheet
metal screw (included). There are no
additional linkages or couplers required.
Clearly labeled electrical terminals simplify
installation. Refer to the damper or VAV box
manufacturer's information to select the
proper timing for the actuator.
Note: The damper rotation time must be
defined at the controller, and the
damper point definition must match
the rotation time of the actuator.
When combined with a VAV controller, the
actuator provides reliable integrated damper
control. See the M9106-AGx-2N0x Series
Electric Non-spring Return Actuators
Application Note, LIT-2681116 for various
configurations with and without the DPT-2015
differential pressure transmitter.
For more information, refer to the
M9106-AGx-2N0x Electric Non-spring Return
Actuators Product Bulletin, LIT-2681126 or
the M9106-AGx-2N0x Electric Non-spring
Return Actuators Installation Instructions,
Part No. 34-636-1077.
Repair Parts
Replace the unit.
To Order
Specify the code number from the
selection chart.
Selection Chart
Code Number Description
Electric actuator with 1 min.
M9106-AGA-2N01
rotation time
Electric actuator with 2 min.
M9106-AGA-2N02
rotation time
Electric actuator with 2 min.
M9106-AGS-2N02 rotation time includes the
DPT-2015 and CBL-2000-1
© 10/01 Johnson Controls, Inc
Rev:
021201
logo:
left ft:
right ft:
standard
Sect# = 0
seQ# = 106