Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Univex Upasta-01
Summary of Contents for Univex Upasta-01
- Page 1 Upasta-01 Operating and Maintenance Manual...
-
Page 2: Table Of Contents
Contents It is forbidden to use the machine before having carefully read the manual, especially the part that concerns operator safety and health. 1. Preliminary information Notes on the use of this Use and Maintenance Manual Manual storage Manual consultation Intended use EC Marking General safety warnings... -
Page 3: Preliminary Information
1. Preliminary information Notes on the use of this Use and Maintenance Manual This document must be considered an integral part of the machine it describes and must as such be stored for the entire machine's lifespan. This document, moreover, must be delivered along with the machine to any other user or owner to whom the machine is transferred. Manual storage This document must be used so as not to damage it and must be stored in a suitable place, without humidity or excessive temperature over the entire lifespan of the machine with which it is enclosed. -
Page 4: General Safety Warnings
General safety warnings All operations performed on the machine, from its use to maintenance to its final demolition, require the presence of suitably qualified staff, in order to limit risks due to inadequate qualification to a minimum. General safety information The manufacturer has designed and checked every machine part and their respective function in the minutest detail, to prevent potential hazards. -
Page 5: Machine Transport, Handling And Warehousing
2. Machine transport, handling and warehousing Packing Machine packing consists of a wooden crate. To correctly handle the crate, use a forklift or pallet transporter. ALL TASKS TIED TO MACHINE HANDLING, TRANSPORT AND WAREHOUSING MUST BE CARRIED OUT BY SPECIALIZED PERSONNEL AND IN FULL COMPLIANCE WITH THE LEGISLATION AND STANDARDS APPLICABLE IN THE COUNTRY WHERE THE MACHINE IS INSTALLED. -
Page 6: Use
3. Use Pasta machine and accessories The supplied machine consists of the main pasta maker casing and the following parts: main parts for pasta dough production (1) dough screw conveyor (2) dough basin (3) drain pipe with open/shut mechanism (4) exhaust ductline in bronze (5) out-feed screw conveyor Parts for pasta dough Parts for diversified production... -
Page 7: Safety Devices
4. Safety devices A microswitch (1) is fitted on the lever atop the dough tank cover; when the lever is lifted, the pasta maker stops running. Every mobile part is protected by a main guard in order to prevent dragging (between rollers) or cutting (pasta cutter blade). WE RECOMMEND THAT YOU CARRY OUT ALL ASSEMBLY, DISASSEMBLY AND CLEANING TASKS ON PARTS WITH THE MACHINE UNPLUGGED FROM ITS SOCKET. -
Page 8: Pasta Maker Die Assembly
Pasta maker die assembly After you have assembled the pasta production components, assemble the die, choosing it based on the desired product: fit the pasta maker die (1) with the ring nut (2) manually tighten the ring nut to the pasta maker as shown in the figure further tighten the ring nut to a halt with the relevant wrench (3) Pasta maker die assembly Pasta cutter blade assembly... -
Page 9: Kneader Assembly
Kneader assembly After having assembled the parts for pasta production, you can assemble the kneader. Place the reel (1) in the kneader unit, as shown in the figure make sure that both locking devices (5) of the pasta maker are lifted and fit the locking pins (2) and (3) of the kneader in their corresponding seats on the pasta maker transmission must be properly connected in order to perform the final fastening operations: the transmission eccentric valve (C) must be engaged in the pasta maker's power socket and the reel must also be mechanically connected to the screw conveyor;... -
Page 10: Ravioli Unit
Ravioli unit An alternative option instead of the tagliatelle accessory is the ravioli maker unit. The unit consists of: (1) main unit (2) filling dispenser (3) filling container (4) piston with rack and pinion for filling feed (5) fixing device of the rack and pinion of the filling piston (6) mold. -
Page 11: Part Disassembly
assemble the mold unit (6), centering the pins (8) of the ravioli unit with the matching holes of the mold turn the flywheel (9) to center transmission and to fully fit in the pins (8) using the figure on the page to the side as reference, grab the ravioli unit and slide it in, as far as possible, between the guides of the kneader pull the flywheel (10) and push the unit to the farthest point release the flywheel (10) -
Page 12: Technical Specifications
5. Technical specifications Pasta maker Pasta maker + Pasta cutter Pasta maker + Kneader... - Page 13 Pasta maker + Pasta cutter + Ravioli maker Upasta-01 Upasta-01 + Pasta cutter Power 0,75 0,75 Voltage/frequency 115V/60Hz 115V/60Hz Tank capacity Dough capacity Production (per hour) Kg/h. Dies Ø mm Net weight...
- Page 14 Univex Corp. 3 Old Rockingham Road Salem, NH 03079 USA info@univexcorp.com SERVICE CENTRE AUTHORISED DEALER...