Table of Contents
Advertisement
Quick Links
Trim size 4.5 x 6.875 in.
Spread size 9 x 6.875 in.
FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
INDUSTRY CANADA NOTICE: CANADA ONLY.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
WARNING!
Requires Speed Class 6 or higher microSD or
CHOKING HAZARD - Small parts.
microSDHC card (not included)
Not suitable for children under 3 years.
microSDHC Logo is a trademark of SD-3C, LLC.
Conforms to safety requirements of RSS210 and FCC.
©2018 Rooftop Brands™ All rights reserved
Tel:+ (1) 949-566-9573 • www.propelrc.com
13
INDOOR/OUTDOOR MICRO VIDEO DRONE
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect the X02 from charger immediately after it is
fully charged. Please refer to enclosed safety instructions.
X02 Micro Video Drone
2.4G Wireless Controller
Made in China
V 1.0
ARTWORK NO.
C60- X02 Manuals
备注：旧机身，带低清摄像头，带气压定高，带读卡器。
X02
INSTRUCTION BOOKLET
PACKAGE CONTAINS:
Spare Parts
USB charging cord
USB Card Reader
Colors and styles may vary slightly.
DESCRIPTION
MDSER
114.3×174.6mm
Vicky
Instruction Manual
DESIGNER
DATE
Cocoa
2018/01/22
Advertisement
Table of Contents
Related Manuals for Propel Trampolines X02
Summary of Contents for Propel Trampolines X02
- Page 1 INSTRUCTION BOOKLET WARNING: Never leave product charging unattended for extended periods of time. Always disconnect the X02 from charger immediately after it is fully charged. Please refer to enclosed safety instructions. PACKAGE CONTAINS:...
-
Page 2: Table Of Contents
Recognizing The Front And Rear Of The X02 ....... . . -
Page 3: X02 Diagram
This ensures that the 6 Axis gyro is properly programmed to mimic your trim settings. Charging Socket Your X02 utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference. -
Page 4: Automatically Take Off / Land
NOTE: The use of the Trim buttons are accompanied with a Beep sound. A single long Beep indicates the controls of the X02. The copter always will tend to self correct and go back to the last locked height after moved up product is center trimmed. -
Page 5: Channel Flight Control
Below is a list of basic flight functions for your long-range remote control X02. While learning to fly your X02 it is best to start with a large space until you get used to the basic controls. As you master flying your X02 it is best to start with a large space until you get used to the basic controls. -
Page 6: How To Do 360º Stunt Rolls
• Turn on your X02 power and properly sync it to the Controller (see HOW TO SYNC YOUR DRONE on page 4 ). • When you have successfully installed your microSDHC card and your quadrocopter is powered up,the flashing red LED lights on the back of the drone will turn solid. -
Page 7: Replacing The Propeller Blades
The X02 is designed for INDOOR or OUTDOOR flight. X02 ‘s blades revolve at high speeds and can cause microSDHC card. damage to the user, spectators and animals. Stand away from the X02 to reduce the risk of getting into the IMPORTANT NOTICE:When your microSDHC card is full the indicator light on the bottom of your flight path.
Need help?
Do you have a question about the X02 and is the answer not in the manual?
Questions and answers