Table of Contents
Advertisement
Quick Links
On this brake, the magnet coil is a separately enclosed unit mounted between an inner and outer armature. When the coil is
properly energized, the armatures are attracted to each other until their outer poles seal. The action of the armatures moves the
shoes away from the wheel. The inner armature moves the inner shoe and the outer armature moves the outer shoe. When the
coil is de-energized, the compression spring forces the armatures apart and presses the shoes against the wheel.
1.
Assemble brake wheel "B" on motor shaft
2.
Back off lock nut "U" and pull rod nut "P" about
one inch.
3.
Back off lock nut "T". Turn screw "C" clockwise to
lift the wedge at the top of the inner shoe lever "L".
4.
Slide the brake into place around the brake wheel
"B" and start bolts into the base mounting surface.
5.
Loosen the holding screws "K" on both shoe
levers leaving only a light grip.
6.
Push the shoe levers "N" and "L" against the
brake wheel "B" and check to insure shoes fit
evenly across the wheel face.
MADE IN U.S.A
INSTRUCTION SHEET
For Type GH505 23" DC Magnetic Shoe Brake
DESCRIPTION OF OPERATION
PROCEDURE FOR INSTALLATION AND OPERATION
(Refer To Dimension Drawing For Mounting Dimensions)
PUBLICATION NO.
7.
Bump the base into the best position to get the
most favorable fit of the shoes against the wheel
"B". C/L of the wheel must be aligned with the
punch mark of base to obtain proper horizontal
positioning of the brake, and with C/L of shoe
pivot sockets to obtain the proper vertical
positioning of the brake.
8.
If the mounting surface is not flat or is not parallel
to the shaft axis, shimming may be necessary.
Tighten the holding bolts to hold the base firmly in
place.
17228
0210
PAGE 1
Advertisement
Table of Contents
Related Manuals for Eaton GH505
Summary of Contents for Eaton GH505
- Page 1 PUBLICATION NO. 0210 INSTRUCTION SHEET For Type GH505 23” DC Magnetic Shoe Brake DESCRIPTION OF OPERATION On this brake, the magnet coil is a separately enclosed unit mounted between an inner and outer armature. When the coil is properly energized, the armatures are attracted to each other until their outer poles seal. The action of the armatures moves the shoes away from the wheel.
- Page 2 17228 PUBLICATION NO. PROCEDURE FOR INSTALLATION AND OPERATION – (Continued) Be sure there is some spring pressure tending to 13. With the brake set, tighten screws “K” on the shoes. separate the two armatures “D” and “F”. This can 14. Note that when the brake is correctly adjusted for proper be tested by turning nut “G”...
- Page 3 17228 PUBLICATION NO. RENEWAL PARTS (Refer to Fig. 2, Page 2) Item Item Description Of Part Part No. Description Of Part Part No. Req. Req. Angle Bracket ……………………... 79-15572-5 Locknut 1½ - 6 ……………………. 15-673 5/8-11 X 1.25 Hex Head Bolt ..11-3558 Spring ………………………………...
- Page 4 17228 PUBLICATION NO. PROCEDURE FOR REMOVAL OF A SHOE LEVER (Refer to Fig. 1, Page 1) If removal of the outer shoe lever “N” is To remove the inner shoe lever “L”, loosen required, loosen locknut “U” and back off nut locknut “T”...
Need help?
Do you have a question about the GH505 and is the answer not in the manual?
Questions and answers
How i can get this spare part
You can obtain the Eaton GH505 spare part by contacting Kor-Pak. You can call them at (888) 256-7725 or submit a request through their contact form, providing your name, organization, email, phone number, title, and description of your request.
This answer is automatically generated