Menu - PRESIDENT Richard ASC Owner's Manual

SCAN
(long press)
Press press for ± 7 seconds or until a beep sounds to
function. The dot between the two channel digits flashes to indicate that
the function is active.
The scanning stops as soon as a signal is detected. The scanning automatically
starts 3 seconds after the end of the transmission and if no key is activated
during 3 seconds. In SCANNING
press the UP/DN buttons (18) on the microphone to change scan direction.
Press PTT switch (17) to exit Scan. The dot between the two channel digits
disappears from the display.
A) DC-POWER TERMINAL (13,8 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
D) JACK FOR PA OPTIONAL SPEAKER (Public Address) (8 Ω,
Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (8 Ω,Ø 2.5 mm)
C) MENU
The order of 14 functions is as described in this manual. However, the func-
tion displayed by entering the MENU will be the last function modified by
user.
The procedure is the same whatever the function is:
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the function to set.
2. Press PUSH knob (6) to validate.
on the display.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to modify the value of the parameter.
4. New press on PUSH knob (6) to
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5. If no key is pressed, the unit exits MENU after 10 seconds.
the display.
Note: UP/DN buttons (18) on the microphone have the same effect as the
rotation of the rotary PUSH knob (6). PTT switch (17)
exists

MENU.

and disappears.
activate the SCAN
mode, turn the PUSH rotary knob (6) or
enter MENU.
is displayed.
The parameter of the chosen function blinks
validate the chosen value. The parameter
disappears from
validates the last setting
1) COLOR
choose
This function allows to
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the COLOR function.
2. Press PUSH knob (6) to validate.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (11) on the microphone
select
to the color. 7 available colors are displayed over and over :
4. New press on PUSH knob (6) to
blinking. a) Go back to point 1 to
PTT switch (17) to validate
5. If no key is pressed, the unit
the display.
Default COLOR is (red).
2) KEY BEEP
When the function is activated, a beep
changing the channel etc. "BP" appears on the display when the function
is active.
Press PUSH knob (6) for 3 seconds to
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the KEyBEEP function.
2. Press PUSH knob (6) to validate.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to activate On / deactivate
4. New press on PUSH knob (6) to validate. The parameter stops blinking. a)
Go back to point 1 to adjust
validate exit MENU.
to and
5. If no key is pressed, the unit
the display.
Default KEY BEEP is On.
3) ROGER BEEP
When the function is active, the icon
The Roger Beep sounds when the PTT switch (17) on the microphone is re-
leased in order to let your correspondent speak. Historically as transceiver
is a "simplex" communication mode, it is not possible to speak and to listen
at the same time (as it is the case with a telephone). Once someone had
25
the backlight color of the display.
enter MENU.
is displayed.
The current color blinks on the display.
validate the chosen color. The color stops
adjust another function or b) Press the
exit MENU.
and disappears on the display.
exits MENU after 10 seconds, disappears on
sounds
when a key is pressed, by
enter MENU. is displayed.
The current status blinks on the display.
Of the function.
another function or b) Press the PTT switch (17)
disappears.
exits MENU after 10 seconds, disappears on
appears on the display.