Configuration; Field Settings - Daikin FBA35A2VEB9 Installation Manual

6 Configuration

a
a a
b
b b
c
c c
1 2 3 L N 1 2 3 L N
1 2 3 L N 1 2 3
P P
1 2
P P
d 1 2
a Power supply
b Main switch
c Fuse
d User interface
▪ Master unit: Be sure to connect the wiring when combining with a
simultaneously operating multi-type in group control.
▪ Use a separate power only in case of following combination:
1×FBA35A + RXS35L or RXM35M
2×FBA60A + RR100/125B or RQ100/125B
2×FBA71A + RR100/125B or RQ100/125B
4×FBA50A + RZQ200C
3×FBA60A + RZQ200C
3×FBA71A + RZQ200C
2×FBA100A + RZQ200C
4×FBA60A + RZQ200C
2×FBA125A + RZQ200C
▪ EN/IEC 61000‑3‑12 provided that the short-circuit power S
greater than or equal to the minimum S
point between the user's supply and the public system.
▪ EN/IEC 61000‑3‑12 =
Standard setting the limits for harmonic currents produced by
equipment connected to public low-voltage systems with input
current >16 A and ≤75 A per phase.
▪ It is the responsibility of the installer or user of the equipment to
ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply
with a short-circuit power S
minimum S value.
sc
▪ Ensure that equipment is connected only to a supply with a short-
circuit power S greater than or equal to S
sc
Combination FBA35A
RZAG71M 2 (—)
RZQG71L
RZAG100M 3 (2.31)
RZQG100L
RZAG125M 4 (3.33)
RZQG125L
RZAG140M 4 (3.33)
RZQG140L
RZASG71M 2 (1.10)
RZQSG71L
RZASG100M 2 (1.65)
RZQSG100L
RZASG125M 4 (3.33)
RZQSG125L
Installation manual
12
a a a
b
b b
c c c
1 2 3 L N
L N L N
1 2 3
P P P P
1 2 1 2
value at the interface
sc
European/International Technical
greater than or equal to the
sc
in table below.
sc
FBA50A FBA60A FBA71A
— — 1 (—)
2 (1.30) — —
3 (2.32) 2 (2.05) —
3 (2.32) — 2 (2.05)
— — 1 (1.22)
2 (—) — —
3 (2.32) 2 (2.05) —
Combination FBA35A
RZASG140M 4 (3.33)
RZQSG140L
Combination
RZAG71M
RZQG71L
RZAG100M
RZQG100L
RZAG125M
RZQG125L
RZAG140M
RZQG140L
RZASG71M
RZQSG71L
RZASG100M
RZQSG100L
RZASG125M
RZQSG125L
RZASG140M
RZQSG140L
INFORMATION
In case of group control it is not necessary to assign an
address to the indoor unit. The address is automatically set
when the power is activated.
6 Configuration
is
sc
6.1

Field settings

Make the following field settings so that they correspond with the
actual installation setup and with the needs of the user:
▪ External static pressure setting using:
▪ Airflow automatic adjustment setting
▪ User interface
▪ Time to clean air filter
To set airflow automatic adjustment
▪ When the air conditioning unit is running in fan operation mode:
1 Stop the air conditioning unit.
2 Set second code number to 03.
FBA35~140A2VEB9+FBA35~71A2VEB9+ADEA35~125A2VEB
FBA50A FBA60A
3 (2.32) —
FBA100A FBA125A FBA140A
— — —
1 (0.73) — —
— 1 (0.74) —
— — 1 (0.74)
— — —
1 (—) — —
— 1 (0.74) —
— — 1 (0.74)
Split system air conditioners
4P456962-1D – 2018.08
FBA71A
2 (2.05)