Related Manuals for Stanley WS10
Summary of Contents for Stanley WS10
- Page 1 WS10 HYDRAULIC WELD SHEAR USER MANUAL Safety, Operation and Maintenance © 2014 STANLEY Black & Decker, Inc. New Britain, CT 06053 U.S.A. 28860 11/2018 Ver. 18...
- Page 2 Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a STANLEY Infrastructure, Milwaukie, Oregon USA...
-
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest certified dealer, call STANLEY Infrastructure at (503) 659-5660 and ask for a Customer Service Representative. WS10 User Manual ◄ 3... -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and maintenance personnel. 4 ► WS10 User Manual... -
Page 5: Safety Precautions
OFF position when coupling or uncoupling the tool. space provided in this manual. Wipe all couplers clean before connecting. Failure The model WS10 Hydraulic Weld Shear will provide to do so may result in damage to the quick couplers safe and dependable service if operated in accordance and cause overheating. -
Page 6: Tool Stickers & Tags
TOOL OPERATOR. TOOL OPERATOR. removal. We suggest you retain this tag and SEE OTHER SIDE SEE OTHER SIDE attach it to the tool when not in use. SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► WS10 User Manual... -
Page 7: Hose Types
This hose is not certifi ed non-conductive and must never be used near electrical conductors. HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from STANLEY. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► WS10 User Manual... -
Page 9: Htma / Ehtma Requirements
2000 psi 2000 psi (At the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) Note: These are general hydraulic system requirements. See tool specifi cation page for tool specifi c requirements. WS10 User Manual ◄ 9... -
Page 10: Operation
It 2. Pour the weld. is a good practice to connect the return hose first 3. As soon as permitted by the mold manufacturer's 10 ► WS10 User Manual... - Page 11 Power unit models should use normally recommended fluids with fluid temperature at or above 50° F/10° C (400 ssu/82 centistokes) before use. Hand pump models may be warmed by placing them in a heated compartment. WS10 User Manual ◄ 11...
-
Page 12: Equipment Protection & Care
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by STANLEY. Supply hoses must have a minimum working pressure rating of 2500 psi/172 bar. 12 ► WS10 User Manual... -
Page 13: Troubleshooting
Weld Shear does not operate. Power unit models, hydraulic lines not connected. Connect lines. Hand pump models, hydraulic pump failure. Locate and remove restriction. Cylinder seal failure. Have inspected and repaired at an authorized Stanley service center. WS10 User Manual ◄ 13... -
Page 14: Specifications
3 dBA Measured A-weighted sound pressure level, Lpa (ref. 20 µPa) at operator’s position, in decibels 66.9 dBA Uncertainty, Kpa, in decibels 3 dBA Values determined according to noise test code given in EN ISO 3744 14 ► WS10 User Manual... -
Page 15: Parts Illustration
PARTS ILLUSTRATION WS10321A, WS1032101A, WS10321AB & WS10321AS WS10 User Manual ◄ 15... -
Page 16: Parts List
Not Pictured, part of valve block assy 29188 GPM Sticker 35294 “NO” Hammer Sticker 35295 Roller Adjustment Sticker 67094 Roller Pivot 67107 Handle Assembly 67116 Elbow 67117 67124 Flow Control Valve Flow Control Valve WS10321AS ONLY 72759 16 ► WS10 User Manual... - Page 17 PARTS ILLUSTRATION WS1022001A, WS102200A WS10 User Manual ◄ 17...
- Page 18 (105-155 lbs / yd (47-70 kg / m Rail)* P/N-27948 68291 Cylinder Shear Blade Set B 70792 Frame Weldment (60-130 lbs / yd (41-60 kg / m) Rail)* P/N-27989 68297 Slide Weldment * Rail Type & Size Determins The Correct Blade Size 18 ► WS10 User Manual...
- Page 20 STANLEY Infrastructure 6430 SE Lake Road Portland, Oregon 97222 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyinfrastructure.com 28860 1/2014 Ver 10...