Amana MBVC Series Installation Instructions Manual

MBVC
BLOWER CABINET
INSTALLATION INSTRUCTIONS
C
ONTENTS
I .............................................................................. 1
NTRODUCTION
E D (ESD) P
LECTROSTATIC ISCHARGE
C P R ........................................................... 2
HECKING RODUCT ECEIVED
R P ...................................................................... 2
EPLACEMENT ARTS
O P .......................................................................... 2
RDERING ARTS
I S I
MPORTANT AFETY NSTRUCTIONS
R S S , W
ECOGNIZE AFETY YMBOLS
G I ................................................................... 3
ENERAL NFORMATION
F .................................................................................... 3
EATURES
A L A L : .......................................................... 3
CHIEVING ESS IR EAKAGE
C A A ......................................................... 3
LEARANCES ND CCESSIBILITY
I ................................................................................. 3
NSULATION
I I .............................................................. 3
NSTALLATION NSTRUCTIONS
B C E
LOWER WITH ASED VAPORATOR
U I .................................................................... 3
PFLOW NSTALLATION
C I ............................................................. 4
OUNTERFLOW NSTALLATION
H I ............................................................... 4
ORIZONTAL NSTALLATION
E C ................................................................ 5
LECTRICAL ONNECTIONS
208/230 V L C
OLT INE ONNECTIONS
L V W ................................................................... 5
OW OLTAGE IRING
O 208 V S
PERATION ON OLT UPPLY
24 V "L " T
OLT EGACY HERMOSTAT
A A S ............................................................... 6
UXILIARY LARM WITCH
C B ...................................................................... 6
IRCULATOR LOWER
T ....................................................................... 10
ROUBLESHOOTING
E D (ESD) P
LECTROSTATIC ISCHARGE
D C ...................................................................... 10
IAGNOSTIC HART
C N ™ S ............................................................... 10
OMFORT ET YSTEM
O ................................................................................ 10
VERVIEW
A C ............................................................... 10
IRFLOW ONSIDERATION
C W ....................................................................... 11
ONTROL IRING
C N ™ S A
OMFORT ET YSTEM DVANCED
D ............................................................................. 13
IAGNOSTICS
N .......................................................... 13
ETWORK TROUBLESHOOTING
S T ............................................................. 13
YSTEM ROUBLESHOOTING
T I
ROUBLESHOOTING NFORMATION
W D ....................................................................... 19
IRING IAGRAM
NOTICE
I "E "
F AN C ERROR IS ENCOUNTERED ON STARTUP
DIP
ELECTRIC HEATER SWITCHES HAVE BEEN SET TO THE APPROPRIATE
. S 7
HEATER SIZE EE PAGES AND
DIP
DELIVERY AND SWITCH SETTINGS
THIS PRODUCT CONTAINS ELECTRONIC COMPONENTS WHICH REQUIRE A DEFINITE
GROUND. PROVISIONS ARE MADE FOR CONNECTION OF THE GROUND. A DEDI-
CATED GROUND FROM THE MAIN POWER SUPPLY OR AN EARTH GROUND MUST
BE PROVIDED.
..................................... 1
RECAUTIONS
....................................................... 2
, L ................................. 2
ORDS AND ABELS
C I .............................. 3
OIL NSTALLATION
.................................................... 5
...................................................... 5
W ............................................ 5
IRING
................................... 10
RECAUTIONS
F ..................................... 11
EATURES
: A H D C
IR ANDLER IAGNOSTIC ODES
,
VERIFY THAT THE
8
FOR THE HEATER KIT AIRFLOW
.
is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
© 2013, 2015-2017 Goodman Manufacturing Company, L.P.
5151 San Felipe, Suite 500, Houston, TX 77056
www.daikincomfort.com - www.goodmanmfg.com - www.amana-hac.com
P/N: IO-438E Date: December 2017
I
NTRODUCTION
This booklet contains the installation and operating instructions
for your modular blower cabinet. All warnings and precautions
within this booklet must be observed. Improper installation can
result in problems ranging from noisy operation to property or
equipment damages, dangerous conditions that could result in
injury or personal property damage and that are not covered by
the warranty. Read this booklet and any instructions packaged
with accessories prior to installation. Give this booklet to the user
and explain its provisions. The user should retain this booklet for
future reference.
NOTE: Upon start up in communicating mode the circuit board
may display an "Ec" error. This is an indication that the dip switches
on the control board need to be configured in accordance with
the Electric Heating Airflow Table in this manual. Configuring the
dip switches and resetting power to the unit will clear the error
code.
E
LECTROSTATIC
NOTE: Discharge body's static electricity before touching unit. An
electrostatic discharge can adversely affect electrical components.
Use the following precautions during modular blower installation
and servicing to protect the integrated control module from dam-
age. By putting the modular blower, the control, and the person
at the same electrostatic potential, these steps will help avoid ex-
posing the integrated control module to electrostatic discharge.
This procedure is applicable to both installed and uninstalled (un-
grounded) blowers.
1. Disconnect all power to the blower. Do not touch the
integrated control module or any wire connected to the
control prior to discharging your body's electrostatic charge
........... 14
to ground.
2. Firmly touch a clean, unpainted, metal surface of the
modular blower near the control. Any tools held in a
person's hand during grounding will be discharged.
3. Service integrated control module or connecting wiring
following the discharge process in step 2. Use caution not
to recharge your body with static electricity; (i.e., do not
move or shuffle your feet, do not touch ungrounded
objects, etc.). If you come in contact with an ungrounded
object, repeat step 2 before touching control or wires.
4. Discharge your body to ground before removing a new
control from its container. Follow steps 1 through 3 if
installing the control on a blower. Return any old or new
controls to their containers before touching any
ungrounded object.
D (ESD) P
ISCHARGE RECAUTIONS