Advertisement
OWNER'S MANUAL
CONTENTS:
Page 1 Specifications
2 Safety Information and Warranty Information
5
6-7
Winch Kit Parts List and Winch Installation Instructions
8
PRESS SPECIFICATIONS
Sunex Model No. A
5740EP
76.25"
32"
5750EP
74"
35"
A - Total Height
B - Inside Width
C - Press Feet Length
D - Bed Width
E - Stroke (Ram Travel Distance From Fully Retracted Position To Fully Extended Position)
F - Pin Diameter
5740EP, 5750EP
B
C
D
E
29.75"
12"
8.25"
29.75"
13"
8"
5740EP - 40 Ton Electric/Hydraulic Shop Press
5750EP - 50 Ton Electric/Hydraulic Shop Press
F
G
1.25"
1 HP Pendant Remote
9.5´/14 AWG
1.25"
2 HP Pendant Remote
9.5´/14 AWG
H
I
Emerson 115V/13.2 AMPS
Emerson 115V/13.2 AMPS
G - Motor Control
H - Power Cord (Length/Type)
I - Mfr/Volts/Amps (Electric Motor)
J - Pb Winch
K - Sliding Head
L - Press Plates Included
© Copyright 2014, Sunex Tools ®
J
K
L
N
N
Y(2)
Y
N
Y(2)
rev. 09/29/14
Advertisement
Related Manuals for Sunex Tools 5740EP
Summary of Contents for Sunex Tools 5740EP
-
Page 1: Table Of Contents
5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press OWNER'S MANUAL CONTENTS: Page 1 Specifications 2 Safety Information and Warranty Information 3 Parts List 4 Ram Assembly Instructions Pump Assembly Instructions Winch Kit Parts List and Winch Installation Instructions... - Page 2 OWNER/USER RESPONSIBILITY If you have any questions about warranty service, please write to Sunex Tools ® The owner and/or user must have an understanding of the manufacturer's This warranty gives you specific legal rights and you may also have other rights...
-
Page 3: Parts List
5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press PARTS LIST ESTIMATED ASSEMBLY TIME: 45 MINUTES 1/2"-13 x 1-1/8" Hex Head Bolts - 2 Press Frame - 1 For Pump Assembly 1/2" Nuts - 2 For Pump Assembly 1/2"-13 x 3/4"... -
Page 4: Ram Assembly Instructions
5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press RAM ASSEMBLY INSTRUCTIONS Forklift located behind press The press must be on a hard, flat surface, bolted to the floor if WARNING necessary in the position in which it will remain for the life of the equipment. -
Page 5: Pump Assembly Instructions
Use adjustable wrench to remove silver filler plug. Install air breather cap in its place. MODEL 5740EP: Follow instructions for installing winch BEFORE attempting to operate press. MODEL 5750EP: Follow instructions for installing winch BEFORE attempting to operate press. - Page 6 5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press WINCH KIT PARTS LIST 5250EP ONLY Cable Clamp - 1 Winch - 1 1/2"-13 x 1-1/2" Hex Head Bolts - 2 Long Cable - 1 1/2" Nuts - 2...
- Page 7 5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press Note: Refer to manual from winch manufacturer for detailed instructions on winch assembly and cable threading procedure. WINCH INSTALLATION INSTRUCTIONS CONTINUED LONG CABLE top view of press...
-
Page 8: Ram Operating Instructions
5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press RAM OPERATING INSTRUCTIONS 1. Check to ensure all connections are secure and all bolts and nuts are tightened. 2. Place press plates DIRECTLY under ram, on press bed. ALWAYS center load and press blocks. -
Page 9: Replacement Parts List
5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press REPLACEMENT PARTS LIST Short Cable Long Cable ITEM NO. SUNEX PART NO. DESCRIPTION QTY. ITEM NO. SUNEX PART NO. DESCRIPTION QTY. Press Bed RS4050WCH Winch Press Frame... -
Page 10: Notes
5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press NOTES 5740EP, 5750EP rev. 09/29/14... - Page 11 5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press NOTES 5740EP, 5750EP rev. 09/29/14...
- Page 12 5740EP - 40 Ton Electric/Hydraulic Shop Press 5750EP - 50 Ton Electric/Hydraulic Shop Press NOTES 5740EP, 5750EP rev. 09/29/14...