Airmar H2183 Owner's Manual & Installation Instructions
Airmar H2183 Owner's Manual & Installation Instructions

Airmar H2183 Owner's Manual & Installation Instructions

Heading sensor

Advertisement

Owner's Guide & Installation Instructions
Smart
Sensor
Heading Sensor
H2183
Model
Patent http://www.airmar.com/patent.html
Record the serial number found on the underside of the sensor.
Serial No.____________ Date of Purchase_______________
17-472-01 rev.07
07/19/18
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H2183 and is the answer not in the manual?

Questions and answers

Summary of Contents for Airmar H2183

  • Page 1 Owner’s Guide & Installation Instructions Smart Sensor ™ Heading Sensor H2183 Model Patent http://www.airmar.com/patent.html Record the serial number found on the underside of the sensor. Serial No.____________ Date of Purchase_______________ 17-472-01 rev.07 07/19/18...
  • Page 2 Information in this manual is subject to change without notice. Airmar reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes.
  • Page 3: Table Of Contents

    Table of Contents Introduction................4 Safety Instructions..............5 Hardware, Tools & Materials........... 6 Where to Purchase Parts............6 Choosing the Mounting Location..........7 Installing................... 8 Mounting on a Vertical Surface..........8 Flush Mounting on a Horizontal Surface........11 Cable Routing & Connecting............12 Connecting to an NMEA 0183 Display........
  • Page 4: Introduction

    Introduction Thank you for purchasing an Airmar solid-state sensor. The compact housing is waterproof with a single removable cable. The H2183 is actually three sensors in a single unit—a three-axis magnetic compass, a three-axis accelerometer, and a three-axis rate gyro. Data is simultaneously output in digital NMEA 0183 and NMEA 2000 formats.
  • Page 5: Safety Instructions

    Always wear safety glasses, a dust mask, and ear protection when installing. WARNING: Steel Vehicle/Boat Do not install the sensor within a steel vehicle/boat because it is a ferrous (magnetic) material. Instead, use Airmar’s model GH2183, combination GPS and compass that can be mounted above the vehicle/boat. WARNING: Compass Safe Distance The sensor must be a minimum of 0.3m (1') from other standard and steering...
  • Page 6: Hardware, Tools & Materials

    Cable ties (some installations) Where to Purchase Parts Lost, broken, or worn parts should be replaced immediately. Obtain parts from your instrument manufacturer or marine dealer. Gemeco Tel: 803-693-0777 email: sales@gemeco.com Airmar EMEA Europe, Middle East, Africa Tel: +33.(0)2.23.52.06.48 email: sales@airmar-emea.com...
  • Page 7: Choosing The Mounting Location

    Choosing the Mounting Location For accurate readings, selecting the best location for the sensor is very important. It can be mounted on either a vertical or a horizontal surface. Choose a location that balances the requirements below. • Mount the sensor as close to the vehicle/boat’s center of gravity as possible. The lower it can be mounted, the more stable it will be, thus giving more accurate compass readings.
  • Page 8: Installing

    7. Fasten the remaining two stainless steel screws in the center holes to lock the bracket in place. level bracket vertical slot (2) stainless steel screw (4) Figure 1. Mounting the bracket Copyright © 2008 - 2009 Airmar Technology Corp.
  • Page 9 NOTE: The arrow on the gasket will face the same direction as the word ‘FORWARD’ on the sensor. sensor (part A) M5 stud (2) (a only) serial number sensor connector socket gasket (part B) arrow (points forward) Figure 2. Preparing the sensor Copyright © 2008 Airmar Technology Corp.
  • Page 10 (2) cable bracket set screw flat washer (2) lock washer (2) thumb nut (2) brass machine screw (2) Figure 3. Installing the sensor in the mounting bracket Copyright © 2008 - 2009 Airmar Technology Corp.
  • Page 11: Flush Mounting On A Horizontal Surface

    Hand-tighten only. Do not over tighten. sensor (part A) alignment M5 stud (2) serial number sensor connector socket gasket (part B) arrow mounting surface flat washer (2) lock washer (2) thumb nut (2) Figure 4. Flush mount Copyright © 2008 Airmar Technology Corp.
  • Page 12: Cable Routing & Connecting

    Depending on the equipment you will be using, route the sensor cable to an Airmar Converter or Combiner, an NMEA 0183 display, an NMEA 2000 network, a laptop, or other device. After reading the cautions below, go to the appropriate instructions.
  • Page 13 RS422 RS232 A /+ OUT TX OUT BARE A/+ IN RX IN B/- IN NO CONNECTION B/- OUT NO CONNECTION SHIELD SHIELD Figure 5. NMEA 0183 Sensor Cable Copyright © 2008 - 2014 Airmar Technology Corp.
  • Page 14: Connecting To An Nmea 2000 ® Network

    Figure 6. NMEA 2000 Sensor Cable [6m (20') shown] Copyright © 2008 - 2011 Airmar Technology Corp. NOTE: Sensor cables longer than 6m (20') have a termination resistor built into the sensor connector (Figure 7). termination resistor in connector locator 120Ω...
  • Page 15: Calibrating The Compass

    Calibrating the Compass WARNING: The internal compass may need to be calibrated after the sensor is installed for maximum accuracy. Perform the pretest below to determine if calibration is necessary. CAUTION: Boat—The Pretest and AutoCalibration Procedure must be done in calm seas in a 0.8 km (0.5 mile) open area away from other boats and ferrous objects such as structures and aids to navigation.
  • Page 16: Maintenance

    • Is the sensor mounted near the center of the vehicle/boat’s fore-aft axis? Firmware Revisions Airmar may release updated versions of the sensor’s firmware. Periodically, check Airmar’s website at www.airmar.com to down-load the latest revision, or contact Technical Support for a CD.

Table of Contents