Scag Power Equipment STWC Operator's Manual page 43

Section 8
Ref. Part
No. No. Description
1 461651 Cutter Deck Advantage
2 43063 Spacer
3 04019-04 Nut, 3/8-16 Serrated Flange
4 481625-01 Wing Nut, 3/8-16
5 481632 Anti-Scalp Wheel
6 04003-26 Bolt, Carriage 3/8-16 x 4"
7 422478 Bracket, Anti-Scalp Wheel
8 04017-27 Bolt, Serrated Flange 3/8-16 x 1"
9 04043-06 Flatwasher, 5/8" Hardened
10 04021-05 Locknut, 3/8-16 Center Lock
11 461295 Discharge Chute
12 04001-11 Bolt, Hex Head 5/16-18 x 1-1/2", Rear
04001-12 Bolt, Hex Head 5/16-18 x 1-3/4", Front
13 04021-10 Nut, Elastic Stop 5/16-18
14 04020-09 Nut, 5/8-11 UNC
15 45944 Shaft, Roller
16 04001-41 Bolt, Hex Head 5/8-11 x 9-1/2"
17 48038 Roller, Rear
18 04001-154 Bolt, Hex Head 5/16-18 x 4-3/4"
19 04063-08 Key, 1/4 x 1/4 x 2"
20 482797 Spring, Idler
21 04043-04 Flatwasher, 3/8"
22 04001-176 Bolt, Hex Head 5/16-18 x 1-3/4" Grade 8
23 04019-03 Nut, Serrated Flange 5/16-18
24 04001-51 Bolt, Hex Head 3/8-16 x 3-3/4"
25 48100-15 Bushing, .376 ID Oilite
26 04030-03 Lockwasher 5/16"
27 04040-15 Flatwasher 5/16"
28 04001-136 Bolt, 3/8-16 x 1-1/2" Grade 8
29 04021-09 Nut, Elastic Stop 3/8-16
30 04001-31 Bolt, Hex Head 3/8-16 x 2-1/2"
31 04001-62 Bolt, Hex Head 3/8-16 x 3.25"
32 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Grade 8
33 04110-03 U-Nut, 3/8-16
34 461663 Spindle Assembly
35 43589 Shaft, Spindle
36 481024 Seal Upper
52A" CUTTER DECK
Ref. Part
No. No.
37 481022
38 48114-04
39 48677
40 43644
41 43312
42 43296
43 481025
44 43297
45 481035
46 43590
47 482878
48 482783
49 48224
50 461632
51 43503
52 423606
423607
53 48926
54 482416
55 04001-172 Bolt, Hex Head 1/4-20 x 1" Grade 8
56 482647
57 423956
58 451240
59 461516
60 04020-16
61 04021-13
62 48763
63 04001-79
64 48114-04
65 482530
66 04001-09
67 482245
68 423803
69 04003-23
70 04021-22
71 04041-07
39
Description
Bearing Assembly
Grease Fitting
Valve, Grease Relief
Housing, Spindle
Spacer, Outside
Spacer, Inside
Seal, Lower
Bushing, Bottom
Nut, Special 1-1/16 - 18
Spacer, Spindle
Cutter Blade 18"
Pulley, Idler 5" Dia
Bearing
Idler Arm Assy.
Idler Pivot
Belt Cover LH (52A)
Belt Cover RH (52A)
Hub, Tapered 1-1/8" Bore
Pulley, Idler 5.0"
Pulley 5.35"
Turbo Baffle Bolt On
Push Arm Shaft
Push Arm (Includes 64,60,62)
Nut, 5/8-18 UNF
Nut, Elastic Stop 5/8-11
Rod End, 5/8 Male RH Thread
Bolt, Hex Head 5/8-11 x 4-1/2"
Grease Fitting, 90 Degree
Belt, Cutter Deck Drive (52A")
Bolt, Hex Head 5/16-18 x 1"
Spring, Discharge Chute
Baffle Weldment, 52A
Bolt, Carriage 3/8-16 x 1"
Nut, Elastic Stop 5/16-18 Grade 8
Flatwasher, 3/8-.391 x .938 x .105