PPA FACILITY CONNECT Technical Manual

WARNING: If the type of end-of-stroke used is the digital
one, after programming the "Default Factory Settings", the
path acquiring is necessary. Otherwise, the ECU will operate
with a minimum path distance of 100 pulses.
FACILITY
TECHNICAL
CONNECT
MANUAL IMPORTANTE
After installing the ECU on the operator, a path acquiring is
ECU
necessary for a proper operation.
If the type of end-of-stroke is the digital one, whenever
the ECU is activated (first command after a power cut), the
motor will be activated (Torque control mode) for opening
until it reaches the mechanical opening stop plate. Once it
has been done, the operation will be normal.
If the type of end-of-stroke is the digital one, whenever
it is necessary to reverse the rotation of the motor, (black
and red wires), the ECU must be turned off. After the
first command, following the reactivation, the operation
procedure will be identical to the previous one. It is not
necessary to reverse the encoder position, since the ECU
corrects its position automatically.
It is necessary to reverse the direction of the motor rotation
in order to adequate the ECU operation to the gate position.
Failure to observe this item can result in inappropriate
operation, since the operation logic for commands and
photocell may be reversed.
WARNING
When using the digital end-of-stroke, while acquiring the
Do not use the equipment
path close to the end-of-stroke, the motor is operating in
without referring to this manual
torque control mode, i.e., the motor keeps continuously
first.
switching on and off.
COMFORT AND SECURITY
Maximum pause time interval is 4 minutes.
P05639 - Rev. 3
P05628 - Rev.3
When using the digital end-of-stroke, if an equipment has
low strength when acquiring the path, one should interrupt
the process and enter the programming mode to increase
the acquiring torque control strength (simultaneously press
the two buttons of the remote control 8 times).

IMPORTANT SAFETY INFORMATION

In order to perform any step when programming the ECU,
Please, closely read and follow all the instructions herein
there is no need to add the two buttons of the remote
in order to use the product properly as well as to ensure an
control. By adding only one button of the remote control,
appropriate installation. All data contained herein are merely
we are able to access all functions regarding the electronics.
informative. We reserve the right to change our products,
When the PROG jumper is open, the GRV button functions
as well as specifications and features, at our sole discretion
without prior notice. as a command for opening / closing the gate.
3. ADDING REMOTE CONTROLS

QUICK REFERENCE GUIDE FOR THE PROGRAMMING

INDEX THROUGH A REMOTE CONTROL

The ECU allows one to add up to 160 remote controls,
Simultaneously press the two buttons of the remote control independently from the fact that either one button or two buttons
(the number of times specified below). It is necessary that at per remote control have been added.
least one of the buttons have been added:
In order to add remote controls:
Once: ECU automatic programming (complete cycle).
1. The gate must be still and must not be counting the pause time
Twice: ECU automatic programming starting by the pause
for automatically closing.
adjustment.
2. Close the PROG jumper. The green SN LED will be dimly lit.
3 times: Erasing all remote controls from the memory.
3. Press and hold the button of the remote control. The green SN
4 times: Default factory settings (Reset).
LED must keep flashing.
5 times: Torque control adjustment (opening/closing).
4. Press and release the GRV button; check the SN LED:
6 times: End-of-stroke position adjustment (opening/closing).
- If the SN LED flashes once: The button of the remote
control has been added.
7 times: End-of-stroke limit adjustment (opening/closing).
8 times: Torque control adjustment when acquiring (opening/ - If the SN LED flashes twice: The button of the remote
control is already added.
closing).
- If the SN LED flashes 3 times: The memory is full.
9 times: Brake activation time adjustment.
10 times: Selecting type of remote control code (fixed/rolling). 5. Release the button of the remote control.
11 times: Selecting type of relay module (electromagnetic 6. In order to add other buttons of other remote controls, go back
lock, courtesy light or traffic light). to step 3.
7. In order to finish the process, open the PROG jumper.

1. MAIN FEATURES

WARNING: In user mode (PROG jumper open), the
Digital / Analog end-of-stroke system. commands of the remote control are only for opening / closing
the gate. In this mode, the ECU will not accept any command
RF 433.92 Mhz Receiver Module.
when the two buttons of the remote control are simultaneously
Rolling Code / Fixed code up to 160 different and button-
pressed.
independent remote controls.
Automatic path acquiring.
4. CHOOSING THE DIGITAL OR ANALOG END-OF-
STROKE
Selection of automatic / semiautomatic mode through remote
control, external program switch and bluetooth.
1. The gate must be still and must not be counting the pause time
for automatically closing.
Programming of the pause time interval for automatic closing
through remote control, external program switch and bluetooth
2. Keep the PROG jumper open.
(maximum time = 4.0 minutes).
3. Choose the end-of-stroke option through the FC jumper:
Electronic clutch (strength) adjustment through remote control,
FC open: Analog end-of-stroke.
external program switch and bluetooth.
FC closed: Digital end-of-stroke.
A command to erase all remote controls through remote control,
external program switch and bluetooth. 4. After choosing the end-of-stroke system, an automatic path
acquiring is necessary. Otherwise, if the digital end-of-stroke
A command to set the ECU (Default factory settings) through
system is chosen, the ECU will operate with a minimum path of
remote control, external program switch and bluetooth.
100 pulses or, if the analog end-of-stroke is chosen, the opening
Output for Courtesy light, Traffic light and Electromagnetic lock
/ closing time will be 120 seconds.
relay module.
Input for an external program switch as a programming device
5. AUTOMATIC PROGRAMMING OF THE ECU
or bluetooth for accessing and programming.
(COMPLETE CYCLE)
Input for photocell.
1. The gate must be open.
Input for loose RF receiver.
2. Close the PROG jumper. The green SN LED will be dimly lit.
Input for pushbutton.
3. Simultaneously press and release the two buttons of the
(added) remote control only once. The SN LED will flash
Delay time interval for opening with a traffic light on.
whenever the buttons are released. After 5 seconds, the ECU
will enter automatic programming mode.
2. DEFAULT FACTORY SETTINGS
4. The gate will close after reaching the FCF (Closing end-of-
Strength = maximum.
stroke) mechanical stop plate or if the two buttons of the
Closing = Semiautomatic mode (Push-to-close). remote control are simultaneously pressed. After one second,
the gate will open, acquiring the path until it reaches the FCA
Strength of torque control when opening = Level 8.
(Opening end-of-stroke) mechanical stop plate or if the two
Strength of torque control when closing = Level 5.
buttons of the remote control are simultaneously pressed.
Strength of torque control when opening (path acquiring) = Level 11.
Strength of torque control when closing (path acquiring) = Level 7.
WARNING: When using the digital end-of-stroke, while
acquiring the path, the motor is operating in torque control
End-of-stroke system = It depends on the FC jumper setting:
mode.
- If the FC jumper is open = Analog end-of-stroke, then:
*Brake time (opening / closing) = 200 milliseconds.
5. The SN LED starts flashing in 'clock mode' (it flashes every
*Opening / Closing time = 60 seconds
second); it will wait for the programming either to automatic or
- If the FC jumper is closed = Digital end-of-stroke, then:
to semiautomatic mode.
*Brake time (opening / closing) = Off.
*Path = 0. WARNING: If the two buttons of the remote control are
simultaneously pressed, the pause adjustment will be cancelled
End-of-stroke limit = Path/16
and it will go forward to the next step; the last adjustment is
Opening End-of-stroke setback = 0 pulse.
kept.
Closing End-of-stroke setback = 0 pulse.
Relay module output = Electromagnetic lock
Automatic mode: In this mode, after opening, the gate
will automatically close after a programmed pause time.
WARNING: When the electromagnetic lock is enabled, the In order to set the pause time interval, one must press and
courtesy light and traffic light are disabled. hold the right button of the remote control, and count the
seconds either by using a watch or by using the SN LED
in 'clock mode'. After counting the pause time, one must
In order to reset the settings for the default factory ones:
release the button of the remote control.
1. The gate must be still and must not be counting the pause time
Semiautomatic mode: In this mode, after opening the
for automatically closing.
gate, a new command for closing is necessary.
2. With the FC jumper, chose the type of end-of-stroke: Analog
In order to set it, one must press and release the left
(open FC jumper) or Digital (closed FC jumper).
button of the remote control.
3. Close the PROG jumper. The green SN LED will be dimly lit.
6. The gate will enter a continuous closing and opening cycle;
4. Simultaneously press and release the two buttons of the (added) then, it will wait for Motor Strength (Electronic clutch)
programming. Such strength must be checked by trying to
remote control 4 times. The SN LED will flash whenever the
manually hold the gate. In order to increase or decrease the
buttons are released. Wait 5 seconds.
strength exerted by the motor, proceed as follows:
5. The SN LED will flash 4 times confirming that the ECU has been
Decreasing the strength: Hold and release the left
reset.
button of the remote control and check the strength again.
6. Open the PROG jumper.
If necessary, one can pausingly press and release the left
button a few times until the desired adjustment.
Increasing the strength: Hold and release the right 8. Adjusting the end-of-stroke position (adjustment up to 10 pulses):
button of the remote control and check the strength again.
Make the end-of-stroke position go back one pulse:
If necessary, one can pausingly press and release the right
Press the left button of the remote control until one
button a few times until the desired adjustment.
reaches the desired adjustment.
Make the end-of-stroke position go forth one pulse:
WARNING: At this stage, the gate will not reach the Press the right button of the remote control until one
mechanical (opening / closing) stop plate; instead, it will reach reaches the desired adjustment.
the point on the path where the speed changes from high to
low. This transition point can be set (See 'Adjustment of the
In order to go back and choose a new adjustment (step 6):
end-of-stroke limit').
Simultaneously press and release the two buttons of the remote
control.
7. When the desired strength level is chosen, one must
In order to finish the programming: Simultaneously press and
simultaneously press and release the two buttons of the
release the two buttons of the remote control or open the PROG
remote control; then, the motor will be switched off and the
jumper.
chosen strength level will be saved in the memory.
WARNING: At this stage, if the PROG jumper is open, the
motor will be switched off and it will not save the strength
adjustment, keeping the previous setting.
8. In order to finish the Automatic Programming (Complete
Cycle), one must open the jumper PROG.
WARNING: the Automatic Programming (Complete Cycle)
can be finished at any moment during the setting cycle of the
ECU, by only opening the PROG jumper.
During the programming process, only a remote control
added to the memory and which has started the programming
is able to interfere or change the setting parameters. In order
to change the ECU programming with another added remote
control, one must restart the entire programming process.
10. ADJUSTMENT OF THE INDEPENDENT OPENING /
CLOSING END-OF-STROKE LIMIT
6. AUTOMATIC PROGRAMMING OF THE ECU (FROM
The end-of-stroke limit is the distance remaining to reach the
PAUSE ADJUSTMENT ON)
mechanical stop plate. The ECU keeps continuously monitoring the
1. Close the PROG jumper. The green SN LED will be dimly lit. gate position and when it reaches the aforementioned limit, the
torque control mode is activated in order to decrease the speed and
2. Simultaneously press and release the two buttons of the
softly reach the stopper.
(added) remote control twice. The SN LED will flash whenever
the buttons are released. After 5 seconds, the ECU will enter 1. The gate must be still and must not be counting the pause time
automatic programming mode (see item 5 from the previous
for automatically closing.
topic – Automatic programming of the ECU (Complete Cycle)).
2. Digital end-of-stroke chosen (FC jumper closed).
3. The gate path must have been previously acquired. Otherwise,
7. ERASING ALL REMOTE CONTROLS FROM THE
the function will be cancelled.
MEMORY
4. Close the PROG jumper. The green SN LED will be dimly lit.
1. The gate must be still and must not be counting the pause time
5. Simultaneously press and release the two buttons of the
for automatically closing.
(added) remote control 7 times. The SN LED will flash whenever
2. Close the PROG jumper. The green SN LED will be dimly lit.
the buttons are released. Wait 5 seconds.
3. Simultaneously press and release the two buttons of the
6. Afterwards, the SN LED will go off and the ECU will wait the
(added) remote control 3 times. The SN LED will flash whenever
programming of the end-of-stroke limit.
the buttons are released. Wait 5 seconds.
7. Adjust the limit and check the SN LED. The function has up to
4. Afterwards, the SN LED will stay lit waiting for either a
7 adjustment levels.
confirmation of the erasing of the remote controls or the
cancellation of the process. 8. In order to set the closing end-of-stroke position, one must
press and release the GRV button. The SN LED will flash once .
In order to cancel the operation: Press and release the
left button of the remote control. The SN LED will again
be dimly lit.
WARNING: If the GRV button is not pressed, the adjustment
Erasing all remote controls: Press and release the right of the torque control strength will be specifically for the
opening cycle.
button of the remote control. The SN LED will flash three
times, indicating that all remote controls have been erased.
5. Open the PROG jumper.
Decrease the end-of-stroke distance: Press the left button of
the remote control until one reaches the desired adjustment.
8. ADJUSTMENT OF THE INDEPENDENT TORQUE
Increase the end-of-stroke distance: Press the right button of
CONTROL STRENGTH FOR OPENING AND CLOSING the remote control until one reaches the desired adjustment.
The ECU will keep 'pulsating' the motor, i.e., it will rapidly keep
In order to finish the programming: Simultaneously press
switching it on and off, so that it has strength even with a low
and release the two buttons of the remote control or open PROG
rotation.
jumper.
The torque control must be adjusted according to the gate weight,
in order to properly open and close it.
When the SN LED:
1. The gate must be still and must not be counting the pause time
for automatically closing.
Intermediate strength limit.
2. Digital end-of-stroke chosen (FC jumper closed).
3. The gate path must have been previously acquired. Otherwise,
the function will be cancelled.
4. Close the PROG jumper. The green SN LED will be dimly lit. Divider Adjustment Index (7 levels):
5. Simultaneously press and release the two buttons of the 04, 08, 16, 32, 64, 128 e 256
(added) remote control 5 times. The SN LED will flash whenever
Example:
the buttons are released. Wait 5 seconds.
Path acquired by the ECU = 1000 pulses.
6. Afterwards, the SN LED will go off and the ECU will wait the
Chosen end-of-stroke limit = Divider 04.
programming of the adjustment of the torque control strength.
Calculation: 1000 pulses/04 = 250 remaining pulses.
7. In order to adjust the torque control in the closing cycle, one
must press and release the GRV button. The SN LED will blink
So, when there are 250 remaining pulses for the gate to reach
once. the mechanical stop plate, the ECU will decrease the speed
in torque control mode, so that the gate softly reaches the
stopper.
WARNING: If the GRV button is not pressed, the adjustment
of the torque control strength will be specifically for the
opening cycle. WARNING: The larger the divider, the lesser the distance for
decreasing the speed, i.e., the gate will be closer to the end-of-
stroke mechanical stop plate.
8. Adjust the strength and check the SN LED. This function has up
to 36 adjustment levels:
11. ADJUSTMENT OF THE INDEPENDENT TORQUE
Decrease the torque control strength: Press the left
CONTROL STRENGTH FOR OPENING AND CLOSING
button of the remote control until one reaches the desired
WHEN ACQUIRING THE PATH
adjustment.
This type of adjustment is identical to the "Adjustment of the
Increase the torque control strength: Press the right
independent Torque Control Strength for Opening and Closing"
button of the remote control until one reaches the desired
but is valid only for path acquiring.
adjustment.
In order to adjust it, one must simultaneously press and release the
two buttons of the (added) remote control 8 times.
When the SN LED:
Blinks slowly once (for two seconds): Minimum
WARNING: This adjustment is only available for the digital
strength level.
end-of-stroke system.
Rapidly blinks: Intermediate strength level.
Blinks slowly once (for two seconds): Maximum 12. INDEPENDENT BRAKE ACTIVATION TIME FOR
strength level.
OPENING AND CLOSING
This type of adjustment allows one to either turn the brake off or
count the time to activate it.
In order to go back and choose a new adjustment (step 6):
Simultaneously press and release the two buttons of the remote 1. The gate must be still and must not be counting the pause time
control. for automatically closing.
In order to finish the programming: Simultaneously press and 2. Close the PROG jumper. The green SN LED will be dimly lit.
release the two buttons of the remote control or open the PROG
3. Simultaneously press and release the two buttons of the
jumper.
(added) remote control 9 times. The SN LED will flash whenever
the buttons are released. Wait 5 seconds.
9. ADJUSTMENT OF THE OPENING / CLOSING END-
4. Afterwards, the SN LED will go off and the ECU will wait the
OF-STROKE POSITION
programming of the end-of-stroke position.
This type of adjustment allows one to move gradually the end-of-
5. In order to choose the closing brake adjustment, one must
stroke back and forth, independently for the opening and closing
press and release the GRV button. The SN LED will flash once .
stoppers.
1. The gate must be still and must not be counting the pause time
WARNING: If the GRV button is not pressed, the adjustment
for automatically closing.
of the brake will be specifically for the opening cycle.
2. Digital end-of-stroke chosen (FC jumper closed).
3. The gate path must have been previously acquired. Otherwise,
6. Adjusting the brake time. The function has up to 11 adjustment
the function will be cancelled.
levels:
4. Close the PROG jumper. The green SN LED will be dimly lit.
Decrease the brake time (SN LED flashes rapidly)
5. Simultaneously press and release the two buttons of the
or turn it off (SN LED flashes slowly): Press the
(added) remote control 6 times. The SN LED will flash whenever
left button of the remote control until one reaches the
the buttons are released. Wait 5 seconds.
desired adjustment.
6. Afterwards, the SN LED will go off and the ECU will wait the
Increase the brake time (SN LED flashes rapidly):
programming of the end-of-stroke position.
Press the right button of the remote control until one
7. In order to set the closing end-of-stroke position, one must reaches the desired adjustment.
press and release the GRV button. The SN LED will flash once.
In order to go back and choose a new adjustment (step 4):
Simultaneously press and release the two buttons of the remote
control.
WARNING: If the GRV button is not pressed, the adjustment
of the torque control strength will be specifically for the In order to finish the programming: Open PROG jumper.
opening cycle.
13. CHOOSING THE TYPE OF REMOTE CONTROL (FIXED
CODE / ROLLING CODE)
1. The gate must be still and must not be counting the pause time
for automatically closing.
2. Close the PROG jumper. The green SN LED will be dimly lit.
3. Simultaneously press and release the two buttons of the
(added) remote control 10 times. The SN LED will flash
whenever the buttons are released. Wait 5 seconds.
4. Afterwards, the SN LED will go off and the ECU will wait the
adjustment of the type of remote control.
For fixed code remote control: Press and release the
left button of the remote control.
For rolling code remote control: Press and release the
right button of the remote control.
5. Open the PROG jumper.
In order to finish the programming: Simultaneously press and
release the two buttons of the remote control or open the PROG
GO FORWARD
jumper. After choosing the type of remote control, the memory is
erased.
14. CHOOSING THE FUNCTION OF THE RELAY
MODULE
1. The gate must be still and must not be counting the pause time
for automatically closing.
2. Close the PROG jumper. The green SN LED will be dimly lit.
3. Simultaneously press and release the two buttons of the
(added) remote control 11 times. The SN LED will flash whenever
the buttons are released. Wait 5 seconds.
4. Afterwards, the SN LED starts flashing in 'clock mode' (one GO BACK
flashing per second) and the ECU will wait for the adjustment
of the relay module function.
For electromagnetic lock: Simultaneously press and release
the two buttons of the remote control.
Operation: When the gate is totally closed and the relay
module is connected to the electronic board, when receiving
a command, the electromagnetic lock will be activated; after
two seconds, the motor will be activated for the opening
cycle; three seconds later, the electromagnetic lock will be
deactivated.
For traffic light: Press and release the left button of the
remote control.
INCREASE THE VALUE OF THE FUNCTION
Operation: The traffic light is switched on whenever the
gate either is opening / closing or is open, waiting for a new
command; then it is switched off when the gate is totally closed.
For courtesy light: Press and hold the right button of the
remote control and count the number of times the LED flashes.
Each time the LED flashes amounts to 10 seconds for the
courtesy light. The adjustment goes from 0 up to 240 seconds.
Operation: The courtesy light stays on whenever the gate either
is opening / closing or is open, waiting for a new command,
and it will be switched off when the gate totally closes or after
reaching the programmed LG time limit.
For an opening delay with traffic light on: Press and hold
the left button of the remote control and count the number of
DECREASE THE VALUE OF THE FUNCTION
times the LED flashes. Each time the LED flashes amounts to 2
seconds for the opening delay with the traffic light on.
WARNING: When the LED flashes more than 8 times, the
delay time will be 15 seconds.
Operation: Whenever the gate is totally closing and whenever
it receives a command for the opening cycle, the traffic light
will be activated and will remain so for the programmed time
interval; then the motor will be activated. The traffic light
will be switched off after the gate finishes its closing cycle or
whenever it receives a new command through the remote
control when the ECU is counting the time for the delay.
COMMAND FOR OPENING OR CLOSING THE GATE
Minimum limit.
Simultaneously and pausingly press and release the two buttons
WARNING: Whenever one changes the relay module
of the remote control in order to activate the motor and check the
programming, the operator will automatically enter torque
Maximum limit.
control mode and it will search the opening stopper gate status.
(poweronreset).
5. Open the PROG jumper
Motor
Motor start
capacitor
Yellow
Black / Red
Red / Black
WARNING: The command for opening or closing the gate
Pushbutton
can be triggered from any screen, either the home screen or
a specific function screen. The adjustment is automatically
Loose
saved, it is not necessary to exit the functions menu to activate it.
receiver
127 or 220 V
(50 / 60 Hz)
INFORMATION SCREEN
It shows the gate status information, sensors and position of the
remote control that has allowed the access through the gate.
End-of-stroke
selection
Analog FCF
jumper
end-of
-stroke
FCA
Courtesy light,
Photocell
Traffic light,
electromagnetic
lock optional
module
Input for
external
program switch
or bluetooth
Button used for adding
Reed (Gate
module remote controls, perform
433.92 MHz RF
position) Status,
adjustments and some
Receiver
open or closed.
Programming functions through a remote
jumper control; it is also used for
opening and closing the
gate.
REMOTE CONTROL
15. EXTERNAL PROGRAM SWITCH
It is used for programming the internal functions in a quicker and
independent way.
Function of the buttons:
= Go forward;
= Go back;
= Increase the value of the function.
= Decrease the value of the function.
= The two buttons simultaneously pressed to activate
the motor.
WARNING: When attempting to program the type of
remote control with the gate moving, the function will be
cancelled and an audible alarm will go off.
When switching the ECU on, the external program switch will
show the messages from pictures 1, 2 and 3 in a row.
ADDING REMOTE CONTROLS
1. It is not necessary to close the ECU's PROG jumper.
2. Press and hold the button of the remote control.
3. The 's' indicator on the screen will show the presence of a The indicator on the screen will show the presence of a indicator on the screen will show the presence of a
remote control. remote control. remote control. remote control.
4. Pausingly press and release the (+) button; the Pausingly press and release the (+) button; the Pausingly press and release the (+) button; the Pausingly press and release the (+) button; the Pausingly press and release the (+) button; the 'g' indicator on indicator on
the screen will show that the remote control has been added. the screen will show that the remote control has been added. the screen will show that the remote control has been added. the screen will show that the remote control has been added. the screen will show that the remote control has been added.
5. The 'n:' addded remote controls counter on the screen is 'n:' addded remote controls counter on the screen is addded remote controls counter on the screen is addded remote controls counter on the screen is addded remote controls counter on the screen is addded remote controls counter on the screen is
updated. updated.
6. Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the 's' indicator will Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the Release the button of the remote control; the indicator will indicator will
disappear from the screen. disappear from the screen. disappear from the screen. disappear from the screen. disappear from the screen. disappear from the screen.
7. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2. In order to add other buttons, go back to item 2.
remote controls
(+) button used
for adding
new remote
controls
ACQUIRING PATH
The ECU enters the closing cycle until it reaches the end-of-
stroke; one second later, it starts the opening cycle, acquiring
the time or pulses of the encoder until the gate reaches the
opening end-of-stroke.
(+) button
used for
starting the
automatic path
acquiring.
WARNING: This function applies for both analog end-of-
stroke and digital end-of-stroke.
CLOSING RAMP
Decrease Increase
distance distance
WARNING: When attempting to program the closing
ramp with the gate moving, the function will be cancelled
and an audible alarm will go off.
OPENING RAMP
Decrease Increase
distance distance
WARNING: When attempting to program the opening ramp
with the gate moving, the function will be cancelled and an
audible alarm will go off.
RAMP TORQUE WHEN CLOSING
Remaining seconds counter for
automatic closing when the ECU
is set for automatic mode.
Decrease Increase
torque 1 level
torque 1 level
at a time
at a time
RAMP TORQUE WHEN OPENING
Decrease Increase
torque 1 level torque 1 level
at a time at a time
ACQUIRING TORQUE WHEN CLOSING
Fixed Rolling
Decrease Increase
code code
torque 1 level torque 1 level
at a time at a time
ACQUIRING TORQUE WHEN OPENING
Decrease Increase
torque 1 level torque 1 level
at a time at a time
STRENGTH
Adjustment of the electronic clutch with the gate either moving or
still; up to 14 levels.
Counter for
added to the
memory
Decrease level Increase level
PAUSE
Adjustment of the automatic closing time when the gate reaches the
FCA opening end-of-stroke sensor.
Decrease time Increase time every
every 10 seconds 10 seconds
ELECTROMAGNETIC LOCK
In a command for opening cycle, if the electromagnetic lock
[S] is enabled and the module connected to the ECU, it will be
activated after one second. The ECU will activate the motor and
two seconds later, the electromagnetic lock will be deactivated.
Deactivate Activate
electromagnetic electromagnetic
lock lock
COURTESY LIGHT / TRAFFIC LIGHT / DELAY TIME
For courtesy light, set the time in xxx seconds; when the ECU
reaches the FCF closing end-of-stroke sensor, it will count the
time for switching it off.
For traffic light, set the time for 000 seconds, when the ECU
reaches the FCF closing end-of-stroke sensor, it will switch it off.
For delay time, set the time between 001 and 015 seconds, and
when this time is reset, the gate will start the opening cycle.
WARNING: In order to activate the courrtesy light or
traffic light functions, deactivate the electromagnetic lock
module [N].
Decrease
Increase time
time every 10 every 10 seconds
seconds
BRAKE TIME WHEN OPENING
Decrease time Increase time
every 100 every 100
milliseconds
milliseconds
BRAKE TIME WHEN OPENING
Decrease time Decrease time
every 100
every 100
milliseconds
milliseconds
RESTORING THE DEFAULT FACTORY SETTINGS
(+) button used
for restoring the
default factory
settings
WARNING: When attempting to program the default
factory settings with the gate moving, the function will be
cancelled and an audible alarm (long beep) will go off.
WARNING: Whenever the (+) button is pressed, the
audible alarm (two short beeps) will be activated indicating
that the action has been performed.
ERASE A REMOTE CONTROL
(+) button
used for
erasing and
starting the
memory
WARNING: When attempting to erase the remote controls
memory with the gate moving, the function will be
cancelled and an audible alarm will go off.
WARNING: Whenever the (+) button is pressed, the audible
alarm (two short beeps) will be activated indicating that the
action has been performed.