Advertisement
Quick Links
Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your
local building permit office to determine the correct hardware in your area.
If you plan to paint or stain your Pergola before assembly, be sure to scribe or mark the
top edge of Joist where Stub Joists and Ladder Blockings are pre-marked. Painting or
staining may cover up markings, making it more difficult to align components later.
Customers agree to hold Outdoor Living Today and any Authorized Dealers free of any
liability for improper installation, maintenance and repair of any Outdoor Living Today
products.
In the event of a missing or broken piece, simply call the Outdoor Living Today
Customer Support Line @ 1-888-658-1658 within 30 days of the delivery of your
purchase. It is our commitment to you to courier replacement parts, free of charge,
within 10 business days of this notification. Replacement parts will not be
provided free of charge after the 30 day grace period.
Toll Free 1-888-658-1658
10ft X 16ft Breeze Pergola
Assembly Manual
Outdoor Living Today
www.outdoorlivingtoday.com
Page 1
Revision #10
March 16th, 2018
sales@outdoorlivingtoday.com
Advertisement
Related Manuals for OLT 10ft X 16ft Breeze Pergola
Summary of Contents for OLT 10ft X 16ft Breeze Pergola
- Page 1 10ft X 16ft Breeze Pergola Assembly Manual Outdoor Living Today Revision #10 March 16th, 2018 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building permit office to determine the correct hardware in your area.
- Page 2 10X16 BREEZE PERGOLA 6 LADDER SECTIONS Thank you for purchasing one of our Breeze Pergola's. Please take the time to identify all the parts prior to assembly. Parts Lists: Thickness Width Length Qty. Specifications: A - Posts 5 1/2” 5 1/2” 108”...
-
Page 3: Hardware Kit
10x16 BREEZE PERGOLA HARDWARE PACKAGE Hardware Kit (Provided) Note: screws and nails shown actual size. 4” 2 1/2” 2 1/2” SS Finishing Nail 2” Square Drive Bit 2” Stainless Wooden Dowel (8) Lag Screw and Washer (24 each) Tools Required (Not Provided) Wood Clamp Hammer... - Page 4 Important - Western Red Cedar Lumber and Timbers will Laying out your Footprint have surface splitting that occurs as lumber seasons To determine the proper placement of your and drys to the moisture content in your area. Splitting 5 1/2” x 5 1/2” Posts, see the exploded view or “checking”, as it is referred to, can be 1/8”...
- Page 5 Important: you will need the Girders to outside help of 2-3 people while lifting and positioning the completed Post/Side Girder Sections into place. Lift up a completed Post/Girder Section slowly and carefully. Make sure B-Girders are facing outward. If Post Mount Hardware is installed, position bottom of Posts in Hardware.
- Page 6 Carefully slide C-Girder down into notch of B-Girders. Be careful not to twist the Girders Girder when pushing up into place. Lag flush on top. Screw with Washers (2) the C-Girder to Post when both pieces are flush with each other.
- Page 7 Complete the remaining 7 Stub Joists aligning and attaching as per Step 8. There are two Joist / Stub Joist Assembly’s, complete both now. Completed Joist/ Stub Joist connections. Carefully lift up completed Joist/Stub Joist Assembly and fit notches onto Girder. 1 - 4”...
- Page 8 On a flat surface, position Ladder Blocking (F) where marked on Main Joist (D) and screw with 2 - 2 1/2” screws per piece. Blocking should be flush with top and bottom of Main Joist with all notches facing down. 2 - 2 1/2”...
- Page 9 Notch slides onto Girder Carefully slide Joist notches of Ladder Section onto Girder. Try to align notches so they fall into place all at once. With notches of Ladder Section all sitting correctly on Girder, slide Section approximately 7” from Post.
- Page 10 (H) Right Side There are 6 Left (G) and 6 Right Sided Bracket Brackets (H). Corner Bracket Post Mounts (I) must be attached to the bottom end of each Corner Bracket before attaching to Posts. Wooden Dowel (I) Corner Bracket Post Mounts Hole...
- Page 11 4” screws countersunk 1/2” below surface. Bracket Left Sided Bracket Spacer flush with bottom of Girder. Important: Posts may need to be aligned so they are true and square to mount Corner Brackets correctly. Use a Level to determine correct Post position. Lift completed Left Sided Bracket up and align bottom of Bracket Spacer flush with bottom of Girder.
- Page 12 Complete both the left and right Brackets on each remaining center post. Once again, make sure both brackets are centered on post and are the same height as the outside corner brackets. 10 x16 Breeze with all Brackets attached. Toll Free 1-888-658-1658 www.outdoorlivingtoday.com sales@outdoorlivingtoday.com Page 12...
- Page 13 Post Post Skirtings with dado cuts - (K) Dado cut skirting(K) Skirting Caps (L) Skirting with Cleat (J) Post Skirtings with Cleat (J) Post mount bolts Locate all Post Skirting pieces. Position 2 post skirtings around the base of post as shown above. Use 1 Post Skirting with Cleat - 1 1/2”...
- Page 14 Congratulations on building your 10X16 Breeze Pergola Note: Our Pergola's are shipped as an unfinished product. If exposed to the elements, the Western Red Cedar lumber will weather to a silvery-gray color. If you prefer to keep the cedar lumber looking closer to the original color, we suggest that you treat the wood with a good oil based wood stain.