Download Print this page

One for All URC 7880 Simple Setup Manual page 2

Hide thumbs Also See for URC 7880:

Advertisement

LEARNING
LEARNING
Your One For All remote control can learn any function from any other working remote
TO DELETE A LEARNED FUNCTION, THE PROCEDURE IS:
control. This can be useful if you are missing one or more functions from your original
remote control and would like to add them to the Smart Control. You can learn onto any
1.
key except Magic, Devices or Activity.
You can also learn a complete device if you can't fi nd a code.
2.
To learn, fi rstly make sure you have all your original remote controls to hand, and that they
have working batteries in. To learn functions, the original remote should be
approximately 3cm from the OFA remote, pointing towards it as shown below:
3.
4.
Press the key to delete twice – the LED will blink twice.
2 - 5 CM
Repeat the above procedure for each key you want to delete.
INPUT
1.
Hold down MAGIC until the LED under the device blinks twice. The LED
under the current mode key will stay lit.
ACTIVITIES
2.
Using the DEVICES key, make sure the LED for the device you want to learn
functions on is lit.
An Activity is a grouping of two or more devices into a single mode based upon what
you're doing while using your remote - for example TV and Set Top Box can be combined
3.
Press 975 – the LED will blink twice.
together into a Watch TV mode. In this mode keys will control only the relevant device, so
GUIDE
in this example the Volume keys would control the TV, but the channel keys would control
4.
Press and release the key you want to learn a function onto (for example
the Set Top Box.
the A key) – The Watch TV, Listen To Music and Custom LEDs will light up.
The OFA Smart Control features 5 Activity Modes; Watch TV, Watch Movie, Listen To Music,
Play Game and Custom. Each of these modes has a choice of devices to combine.
5.
Press and release the key on the original remote.
These are:
6.
WATCH TV
The LED will blink twice to indicate the key has been learned correctly.
Combination 1:
7.
Repeat steps 4 and 5 for each key you want to learn – remember you can learn from multiple
Combination 2:
remotes, but only one function per key.
Combination 3:
Combination 4:
8.
When you learned all the functions you require, press and hold the MAGIC
Combination 5:
key until the LED blinks twice and turns off .
WATCH MOVIE
Combination 1:
Hints
Combination 2:
If the LEDs shows one long blink at step 6, the function was not learned correctly, please try again
Combination 3:
from step 4.
Combination 4:
If you fi nd one or more keys don't work properly after set up, you can re-enter the learning mode
Combination 5:
at any time by repeating the procedure from step 1.
Combination 6:
LISTEN TO MUSIC
Combination 1:
Combination 2:
Combination 3:
Combination 4:
Combination 5:
Smart 8 USA_UK QSG.indd 2
ACTIVITIES
PLAY GAME
Combination 1:
TV + GAME (Default)
TV + GAME + AUD
Hold down MAGIC until the LED under the device blinks twice.
Combination 2:
The LED under the current mode key will stay lit.
Combination 3:
TV + GAME + S.BAR
Using the DEVICES key, make sure the LED for the device you want
CUSTOM
to delete functions from is lit.
Combination 1:
TV + MEDIA (Default)
Press 976 – the LED will blink twice.
Combination 2:
TV + MEDIA + AUD
Combination 3:
TV + MEDIA + S.BAR
Combination 4:
TV + GAME
Combination 5:
TV + GAME + AUD
Combination 6:
TV + GAME + S.BAR
If you set up the default devices for any Activity on the remote (for example a TV and STB
for Watch TV) that Activity will be set up automatically on the remote. If you would like to
change to a diff erent combination, the procedure is as follows:
1.
Hold down MAGIC until the LED under the device blinks twice.
The LED under the current mode key will stay lit.
2.
Use the ACTIVITY key to scroll through the Activities until the
one you want to set is fl ashing.
3.
Press the number of the combination you want to set – e.g 2
for TV + STB + AUD in Watch TV.
TV + STB (Default)
4.
TV + STB + AUD
The LED will blink twice and go out.
TV + AUD
TV + S.BAR
To access the Activities, simply press the ACTIVITY key to scroll through until the desired
TV + STB + S.BAR
one is lit. You can return to controlling by device by using the DEVICES key.
INPUT Shift
TV + BLU (Default)
As the INPUT key is intended to select the input on your TV and most TVs use a menu to
TV + BLU + AUD
select from a list of inputs, when the INPUT key is pressed in an Activity, the Menu Up,
TV + DVD
Down, Left, Right and OK keys temporarily control the TV. If the OK key is pressed, or no
TV + DVD + AUD
key is pressed for ten seconds, these keys will revert to controlling the relevant device for
TV + BLU + S.BAR
the Activity (e.g. STB in Watch TV Mode).
TV + DVD + S.BAR
Power Macro
If you hold down the Power key for 2 seconds in any Activity, the remote will send the
TV + AUD + MEDIA (Default)
Power function for each device contained within that Activity. So for example, holding
TV + S.BAR + MEDIA
Power in the default setting for Watch TV will turn both the TV and Set Top Box on or off .
TV + AUD + BLU
AUD only
S.BAR only
MACROS
MACROS
PROGRAM A MACRO
MACROS ON ACTIVITIES
You can program any key on your OFA remote (except MAGIC, DEVICES and the three App
Another handy feature of the Smart Control is to put Macros on Activities; you could for
Shortcut keys) to send multiple commands on a single press –a Macro. This can be useful
example program the Watch TV Activity to send a Macro to turn on the TV and Set Top
for controlling multiple devices to put them in a certain state – for instance you could put
Box when selected. To do this, simply use the Activity key to select the Activity in step 3 of
your TV on HDMI 1 and press Play on the Blu-ray player to start watching a movie. A key
the procedure "Program a Macro". Next time you use the Activity, the Macro will be sent 3
programmed with a Macro will send the same Macro regardless of the device mode, so it
seconds after you select it using the Activity key.
is best to select a key you don't use, or use one of the spare A, B or C keys.
To program a macro, the procedure is as follows:
If you want to delete a Macro from the Activity, select it during step 3 of "To Delete a
Macro".
1.
Hold down MAGIC until the LED under the device blinks twice.
The LED under the current mode key will stay lit.
VOLUME LOCK
2.
Press 995 – the LED will blink twice.
If you always use one device to control volume, for example your TV or an AV Receiver, you
3.
Next select the key you want to program the Macro on.
can set up the Smart Control to always control that device, regardless of which device your
remote is controlling.
4.
Now use the DEVICES key to select the device you want the fi rst
To do this:
function of the Macro to come from, for example TV.
1.
Hold down MAGIC until the LED under the device blinks twice. The LED under the
5.
Next, press the key you want to include in the Macro, for example
current mode key will stay lit.
INPUT
2.
the INPUT key.
Press 993 – the LED will blink twice.
3.
Use the DEVICES key to select the Device you want to lock the Volume to.
6.
4.
Repeat steps 4 (if necessary), and 5 to add more keys to the Macro. You can include up
Press MAGIC once – the LED will blink twice and volume is now locked.
to 15 key presses.
If there is one particular device you would like to exclude from the Volume Lock (and
7.
To store the Macro, hold down the MAGIC key until the LED blinks
control its own volume), you can do this by the following:
twice.
1.
Hold down MAGIC until the LED under the device blinks twice. The LED under the
* Remember to press the keys in the same order you would using your original remotes – so if you pressed AV on the TV
current mode key will stay lit.
remote and then Play on the Blu-ray remote to watch a movie, do it in the same order on the Smart Control.
2.
Press 993 – the LED will blink twice.
* If the LED shows a long blink when you press a key in steps 3 or 4, you have entered too many keys, please try again.
3.
Use the DEVICES key to select the Device you remove from Volume Lock.
4.
Press VOLUME DOWN – the LED will blink four times and device is now removed.
TO DELETE A MACRO
If you want to remove a macro from a key, please perform the following:
To unlock the volume and set every device back to controlling its own volume, the
procedure is:
1.
Hold down MAGIC until the LED under the device blinks twice.
1.
The LED under the current mode key will stay lit.
Hold down MAGIC until the LED under the device blinks twice.
The LED under the current mode key will stay lit.
2.
2.
Press 995 – the LED will blink twice.
Press 993 – the LED will blink twice.
3.
Press VOLUME UP – the LED will blink four times and Volume is now unlocked.
3.
Press the key the macro is programmed on.
Please note that Volume Lock only applies in Device Mode – Activities are unaff ected.
4.
Now hold down the MAGIC key until the LED blinks twice –
the Macro is deleted.
INPUT
APP SHORTCUT FEATURE
The Smart Control features 3 App Shortcut keys for viewing digital TV, streamed over the
internet. If your original remote control already had a key for this - for example many newer
TVs have a Netfl ix key - then this key will perform exactly the same as the key on your
original remote. However if you did not have a key like this, but still had the ability to watch
a streaming service, you can use this key as a shortcut by programming a macro on it. Most
AV devices which are connected to the internet, such as Smart TVs or streaming Set Top
Boxes have one or more applications they can run to access TV viewing via the internet.
INPUT
Examples of these would be Netfl ix, YouTube, Amazon Prime, BBC iPlayer or similar.
To program the macro, you fi rst need to know the device you use to access the service, and
then the sequence of keys you need to press to always bring up the service you prefer, For
example, some Panasonic TVs will start Netfl ix by pressing the Apps key, then Menu Down
Twice, and fi nally the OK key. Or on an Apple TV, the sequence is Menu, Menu Down and OK.
Once you have determined the sequence for your device, follow these steps:
1.
Sit in front of your device with It switched on (not on standby)
2.
Hold down the App Shortcut key until the LED blinks twice and stays lit
3.
Use the DEVICES key to select the device you want to use for the
App Shortcut macro (e.g. TV)
4.
Now perform the sequence of keys exactly as would normally.
The remote will operate your device and the macro is recorded in
real time - so if it normally takes a few seconds for your device to
react don't worry.
5.
One you have fi nished the sequence - and the Streaming Service
has started on your device - hold down the App Shortcut key until
the LED blinks twice and goes out. The macro is now stored.
Tips
Make sure the Smart Control Is operating the device in question before programming
If you fi nd the Macro doesn't work as expected, you can just repeat the same
sequence to reprogram
When programming, wait for your device to respond fi rst, the remote will remember
the timing
The App Shortcut macro is tied to one device, remember to make sure you are
watching the correct device.
Customer Support: 855-716-2573 (toll free)
OFA warranty/terms & conditions: 855-569-6595 (toll free)
www.oneforall.com
Imported into the US by:
Universal Electronics Inc.
UEI Technical Support Services,
Suite 301
26250 Euclid Ave.
Euclid, OH 44132
711753
One For All is a registered trademark of UEI
RDN 1250618
Made in China, Hecho en China
25-06-18 09:57

Advertisement

loading