Signal Connections; Analog Rf Antenna Connection; Digital (Dtv) Antenna Connection; Setting Up The Tv - Sanyo HT27744 Owner's Manual

Signal Connection

Analog RF Antenna Connection

Connecting Analog Cable service, RF antenna,
or Satellite Receiver to the TV Analog
(UHF/VHF/CATV) 75 ohm terminal.
CABLE
SATELLITE RECEIVER
CATV IN
CH3
CH4
OUT TO TV S-VIDEO
Note: If you do not
have a VCR connect
signal directly to the TV
75 ohm terminal.
TV BACK
COMPONENT VIDEO INPUT
ANALOG
AUDIO
Y
OUTPUT
L
P
b
R P
r
COMPO 3 COMPO 2
To connect a High-Definition cable or satellite set-top box, go to page 8.

Setting Up the TV

NOTE: When the television is powered on for the first time, it automatically checks to make sure an RF
input signal is connected. After you have made all necessary connections, continue as follows...
1. Press the CHANNEL UP key to automatically search and scan for available channels: Digital (DTV) and
Analog (NTSC). The Channel Search contains two processes that are executed simultaneously for digital and
analog channels, therefore, this will take a few minutes.
NOTES:
The on-screen message for digital search will appear with the channel number, a progress bar, and
percentile number displayed across the bottom of the screen (to indicate activity) as the search process
continues. This may take some time, so please be patient.
Channel information found during the channel search is stored in the Channel Scan Memory database.
The HD television will be tuned to the lowest Digital channel or lowest Analog channel if no digital
channels are found.
2. To change the initial analog tuning system setup (from antenna to cable or cable to antenna), use the on-screen
menu. See "Antenna Selection" on page 17.
3. After channel search is complete, the TV will begin Auto Clock setting. This feature searches for a local PBS
station that is broadcasting an extended data service signal. This signal is used to automatically set the clock/day.
(This may take several seconds.)
To cancel auto clock setting, press the CHANNEL UP key. (To set the clock manually, see page 20.)
RF ANTENNA
TV BACK
VIDEO L- AUDIO -R IN FROM
SAT.
VIDEO L- AUDIO -R
ANALOG
SIGNAL
SPLITTER
IN VCR
FROM ANT.
OUT
OUT TO TV
S-VIDEO
AUDIO 3
VIDEO
UHF/VHF/CATV
L
(MONO)
AUDIO
R
VIDEO 2 VIDEO 1

Digital (DTV) Antenna Connection

Connect RF antenna to the splitter, then to
the TV Digital Antenna In Terminal.
Note: RF Antenna can be
connected directly to the 75
ohm terminal. In fringe recep-
tion areas, it may be better to
DIGITAL
connect separate RF antennas.
SIGNAL
HDMI
INPUT
CATV FRANCHISE NOTE:
Cable companies, like public
utilities, are franchised by
DIGITAL
local government authorities.
AUDIO
To receive cable programs,
OUTPUT
even with equipment which
DIGITAL
is capable of receiving cable
ANTENNA IN
channels,
must subscribe to the cable
company's service.
SERVICE
Signal Connection : Digital/Analog / Setting Up the TV
QuickTips
The TV will auto-
■
matically select an
Antenna mode for the
type of Analog RF
signal you connect.
Use "Antenna Selec-
tion" in the Setup
menu to change
Antenna mode.
TV will switch off
■
automatically after
15 minutes if there is
no signal reception
(cable out or station
not broadcasting).
Exception—When a Video
mode is selected, the
TV will not automati-
cally switch off when
signal reception
has stopped for 15
minutes.
If you move the TV to
■
a new location, press
the consumer
the RESET key twice
after connecting the
signal and turning on
the TV.
Need help?
Visit our Web site at
www.sanyoctv.com
or Call 1-800-877-5032
First First
Please connect all signals Please connect all signals
and antennas to jacks and and antennas to jacks and
the terminals on the back. the terminals on the back.
Then press the Channel UP key. Then press the Channel UP key.
Please wait,
while your TV searches
for available channels.
Digital Antenna 35
Please wait, Please wait,
Automatic clock setting. Automatic clock setting.
Press Channel UP Key to cancel. Press Channel UP Key to cancel.
50%
7