Altinex MT105-8X8 User Manual

MT105- - - - 120/121/8X8, MT105 MT105 MT105 120/121/8X8, 120/121/8X8, 120/121/8X8, 8X4 Video
Welcome!
We greatly appreciate your purchase of the MT105-120/121 8X8/8X4 Video -
Matrix Switcher (15-Pin HD In/Out). We are sure you will find it reliable
and simple to use. Superior performance for the right price, backed by solid
technical and customer support is what ALTINEX has to offer.
We are committed to providing our customers with
Signal Management Solutions ® to the most demanding audiovisual
installations at very competitive pricing and we welcome you to join the
ranks of our many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your MT105-120. Keep this
manual handy for future reference. These safety instructions are to ensure
the long life of your MT105-120 and to prevent fire and shock hazards.
Please read them carefully and heed all warnings.
1.1 General
•
Qualified ALTINEX service personnel or their authorized
representatives must perform all service.
1.2 Installation Precautions
•
To prevent fire or shock, do not expose this unit to water or moisture.
Do not place the MT105-120/121 in direct sunlight, near heaters or heat
radiating appliances, or near any liquid. Exposure to direct sunlight,
smoke, or steam can harm internal components.
•
Handle the MT105-120/121 carefully. Dropping or jarring can damage
the card.
•
Do not pull the cables that are attached to the MT105-120/121.
•
Insert the card carefully into the slots of the MultiTasker without
bending any edges.
2. Installation Procedures
Step 1. Turn off power to the MultiTasker system and disconnect from AC power.
Step 2. Remove a slot cover (MT200-101) from one of the unused slots. Identify the slot number and note that it is for RS 232 control.
Step 3. Slide the MT105-120/121 into the slot in the MultiTasker enclosure in order to connect to the bus. Make sure that the MT105-120/121 card fits into
place.
Step 4. Secure the card to the MultiTasker by tightening the retainer screws located on the top and bottom of the MT105-120/121.
Step 5. Connect a VGA-type cable from the video source to the input connector of the MT105-120/121.
Step 6. Connect the output connectors of the MT105-120/121 to the display devices through a VGA type cable.
Step 7. Restore power to the MultiTasker system.
3. Limited Warranty/Return policies
Please see the ALTINEX website at www.altinex.com for details on warranty and return policies.
400-0362-005
8X4 Video- - - - M M M M atrix Switcher 8X4 Video 8X4 Video
1.3 Cleaning
•
Clean only the connector area with a dry cloth. Never use strong
detergents or solvents, such as alcohol or thinner. Do not use a wet
cloth or water to clean the card. Do not clean or touch any component
or PCB.
1.4 FCC Notice
•
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
•
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
Any changes or modifications to the unit not expressly approved by
ALTINEX, Inc. could void the user's authority to operate the
equipment.
1
atrix Switcher atrix Switcher atrix Switcher
User's Guide