HIKVISION DS-PD2-T10AME-EH User Manual

DS-PD2-T10AME-EH
10m
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized
D i a g r a m R e f e r e n c e
References
technology to detect when one or both PIR detectors as well as the
Microwave module are Masked.
view of the PIR or MW sensors.
The masking area is adjustable between 0 to 1M.
detector, the obstacle must be removed and a walk test should be done.
terminal has to be connected to an output of the panel which is POSITIVE
when ARMED. To enable this feature also, switches 2 and 4 must be OFF.
Blocking:
or less and is used when the panel is disarmed. When the blocking feature is
To enable the feature, switches 3 and 4 must be OFF and the RI input
should be connected to an output on the control panel which gives a
NEGATIVE when DISARMED and a POSITIVE when ARMED.
Detectors technical characteris cs Detectors technical characteris cs
Automa c sensi vity yes 10m (13m with curtain lens)
Digital temperature compensa on yes
Volumetric coverage Yes
DEOL resistor on board yes
Curtain coverage Op onal
Tamper protec on Front and rear
Animal immunity 10kg
Intergrated walk test buzzer yes
Tri technology 2 infrared and 1 microwave
Separate LED indica on Microwave, infrared and alarm
Detec on speed 0.25 - 2.5m/s
3 microwave frequencies to avoid yes
Coverage angle 90 degree (142 degree with curtain lens)
Digital independent oa ng yes
Detec on zones 78 (24 with curtain lens)
An -sway analy cs yes
Detec on planes 5 (1 with curtain lens)
Adjustable sensi vity Auto or high
Adjustable an masking (an spray) Yes
Electrical & ba ery
Protec on Ultraviolet light lter
Opera ng voltage 9-16VDC
Lens 2 x Lens 5 volumetric lens (UV Compensated)
Quiescent current consump on mA
Op cs Sealed op cs
Relay outputs 3 x SELV limits, 60VDC 50mA (42.4VAC peak)
Detec on method 2 low noise dual element passive infrared
Tamper switch 12VDC 50mA both front and rear
An blocking technology Yes
Cer ca ons and warranty
Moun ng
Electrical conformity CE
Warranty 2 years Wall mounted Yes - addi onal wall and xed brackets
Environmental and opera ng features Op mum coverage height 2.4m
opera ng temperature -30 to +70
Physical dimensions (H x W x D) 188 x 84 x 77mm
Weight 300g
Adjustable Lens Masks
FIXEDBRACKET + Fixed Lens Mask
Warning
For electrical products sold within the European Community. At the end of
the electrical products life, it should not be disposed of with household
or retailer for recycling advice in your country.
Frequency
This product operates in a European non-harmonized frequency band.
Hereby, Pyronix, declares that this is in compliance with the
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
About this Manual
This manual is applicable to detector.
other r atest version in the company website
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
START
3EOL
3k
15k
12k
8k2
6k8
5k6
EOL EOL EOL R1 LED ALARM N/O EOL
4k7
TAMPER ALARM N/C MASK/FAULT TAMPER
2k2
1k
10k 10k
6k8 5k6
5k6 4k7
4k7 3k9
2k7
3k9
2k2
2k7
1k5
2k2
A A T T 1k
+12V 0V 1k5 +12V 0V
EOL INPUT 1 COM
1k
820R
1M
MAX
Max: 1M
30% Mask
1m
WALLBRACKET
FIXEDBRACKET
MASK/ALARM LINK
DEOL N/C
3k
15k
12k
8k2
6k8
5k6
EOL EOL R1 LED ALARM N/O EOL EOL EOL R1 LED
4k7
ALARM N/C MASK/FAULT TAMPER ALARM N/C MASK/FAULT
2k2
1k
10k 10k
6k8 5k6
5k6 4k7
4k7 3k9
2k7
3k9
2k2
2k7
1k5
2k2
A A T T 1k A A T T
1k5 +12V 0V
EOL INPUT 1 COM EOL INPUT 1 COM
1k
820R
30%
OFF
>1m
!
The Input voltage should meet both the SELV (Safety Extra Low Voltage) and
the Limited Power Source according to the IEC60950-1 standard. Please refer
to technical specifications for detailed information.
GENERAL WIRING
HIK
3k
15k
3k
12k
15k
8k2
12k
6k8
8k2
5k6
6k8
ALARM N/O
4k7
5k6
EOL EOL EOL R1 LED ALARM N/O
2k2 4k7
TAMPER ALARM N/C MASK/FAULT
2k2
1k
1k
10k 10k
10k
10k
6k8 5k6
6k8 5k6
5k6 4k7
4k7
5k6
4k7 3k9
4k7 3k9
2k7 2k7
3k9 3k9
2k2 2k7 2k2
2k7
2k2 1k5
1k5
2k2
Z1 COM Z2 Z3 1k
+12V 0V 1k5
1k
1k5
1k
HIK CONTROL PANEL
1k
820R
820R
EOL EOL EOL R1 LED ALARM N/O
TAMPER ALARM N/C MASK/FAULT
+12V 0V
PCX 46
PCX
ATE INPUTS
OFF
GENERAL
3k
15k
12k
8k2
6k8
5k6
EOL EOL EOL R1 LED
ALARM N/O
TAMPER ALARM N/C MASK/FAULT 4k7
2k2
1k
10k
10k
6k8 5k6
4k7
5k6
4k7 3k9
2k7
3k9
2k7 2k2
1k5
2k2
Z1 COM Z2 Z3
+12V 0V 1k5 1k
1k
GENERIC CONTROL PANEL
820R
3k
15k
12k
8k2
6k8
5k6
4k7
2k2
1k
10k
10k
5k6
6k8
5k6 4k7
4k7 3k9
2k7
3k9
2k2
2k7
1k5
2k2
1k5 1k
1k
820R
No resistors are required for
the Alarm N/O relay