Special Mode Setting Button (For Avr-S710W) - Denon AVR-X1200W Service Manual

Special mode setting button (for AVR-S710W)

No. 1 - 6, 9 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power.
b
No. 7, 8 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds .
b
No. 10 : While holding down buttons "A" and "B" simultaneously, insert the AC plug into the wall outlet to turn on the power.
b
No. Mode
Version Display
1
(u-COM / DSP Error Display)
2
Selecting the Mode for Service-related
2-1
Protection history display mode
2-2
Check the Video/Audio path Mode
2-3
Remote ID Setup Mode
2-4
TUNER STEP Mode
2-5
Operation Info Mode
3
User Initialization Mode
4
Factory Initialization Mode
5
PANEL / REMOTE LOCK Selection Mode
6
Protection Pass Mode
7
CY920 Reboot Mode
8
CY920 Initialization Mode
9
USB Update Mode
10
Forced USB All Device Write Mode
SOURCE SELECT
Button A Button B Button C
DIMMER STATUS
TUNER
PRESET CH TUNE -
+
↑ -
↑ -
↑ -
↑ -
↑ -
TUNER TUNER
PRESET CH PRESET CH
- +
TUNER
PRESET CH TUNE -
+
TUNER
ZONE2
PRESET CH
SOURCE
+
TUNER
ZONE2
PRESET CH
SOURCE
+
TUNER TUNER
PRESET CH PRESET CH
- +
TUNER
PRESET CH TUNE -
+
ZONE2
TUNE +
SOURCE
ZONE2
TUNE +
SOURCE
TUNER
ZONE 2 ON/OFF ZONE 2 SOURCE
PRESET CH
1 CBL/SAT 2 DVD/Blu-ray
PHONES
MOVIE MUSIC GAME
SOUND MODE
ZONE2 TUNER
X
SOURCE PRESET CH +
TUNER
PRESET CH －
Displays the version of firmware such as the main firmware or DSP.
- Errors that have occurred are displayed.
(See page 21)
This is a display for turning on each service-related mode.
TUNE +
Service-related modes: No. 2-1 - No. 2-5
Displays the protection occurrence history.
-
(See page 44)
This is a special mode for service confirmation used during repair
work to simplify the confirmation work for the Audio channel /
-
video channel.
(See page 27)
If there are multiple DENON AV receivers in the same area, this
mode prevents other AV receivers from being operated concur-
-
rently with this device.
(See page 48)
Enables reception STEP of the ANALOG TUNER to be changed.
-
(See page 47)
Displays the accumulated operating time of the unit, the number
of times the power was switched on, and the number of occurrenc-
-
es of each protection.
(See page 46)
Initializes backup data.
-
(Settings for the Installer Setup are not initialized.)
Initializes backup data.
-
(The settings for the Installer Setup is also initialized.)
Start this unit in the PANEL/REMOTE LOCK selection mode so that
PANEL LOCK and Remote Lock can be switched between ON and
-
OFF.
(See page 25)
Enables the power to be turned on when protection detection is
TUNE + disabled.
(See page 49)
- The CY920 is restarted after CY920 hang up.
Enter this mode only after replacing Flash for CX870 / CY920 and
-
rewriting the firmware.
- Switches this unit to USB Update mode.
Mode used when this unit cannot be recovered.
- Forcibly switches this unit to USB update mode.
(See page 56)
TUNE BAND MODE DIMMER STATUS
3 GAME 4 ONLINE
QUICK SELECT
AUX - HDMI SETUP MIC
PURE
5V/1A
TUNE + STATUS
TUNE － DIMMER
20
Descriptions
MASTER VOLUME