Denon AVR-X1200W Service Manual page 58

Error
USB Update Error Display
Code
15
U p d a t e C h e c k N G
16
U p d a t i n g
20
C o n n e c t i o n F a i l 2 0
21
F i l e s N o t F o u n d
22
N o t M a t c h F i r m
23
C o n n e c t i o n F a i l 2 3
24
C o n n e c t i o n F a i l 2 4
25
C o n n e c t i o n F a i l 2 5
26
D o w n l o a d
27
C o n n e c t i o n f a i l 2 7
36
C o n n e c t i o n F a i l 3 6
37
F i l e s N o t F o u n d
38
N o t M a t c h F i r m
39
C o n n e c t i o n F a i l 3 9
3A
C o n n e c t i o n F a i l 3 A
3B
F i l e s N o t F o u n d
Error in Verify after rewriting Main
1 5
(Check Sum Error).
Setup failure of the XModem
f a i l 1 6
transfer method.
Unable to detect USB after SBL
Mode.
No Firmware File in USB after SBL
2 1
Mode.
After SBL Mode, the Firmware File
in the USB does not support your
2 2
model and area.
Failed to obtain the entire Firm-
ware information after SBL Mode.
Time Out while obtaining the
entire Firmware information after
SBL Mode.
Failed to transit to SBL Mode.
Time Out in Download (writing to
f a i l 2 6
SDRAM) for Firmware Download.
Failed to write to EEPROM after
SBL Mode.
Unable to detect USB.
No Firmware File in USB.
3 7
The Firmware File in the USB does
3 8
not support your model and area.
Time Out in USB Check.
Unable to detect USB for Firm-
ware Download.
No Firmware File for Firmware
3 B
Download.
58
Details of Error code Remedies
This unit automatically retries the
request several times. Wait until the
Display stops. If the Display stops at the
Error display, press and hold the "Power
operation" button for 5 seconds.
This unit automatically retries the
request several times. Wait until the
Display stops. If the Display stops at the
Error display, press and hold the "Power
operation" button for 5 seconds.
Disconnect and reconnect the USB
memory.
Make sure that the Firmware File is in
the USB memory.
Make sure that the model name and
area are supported by the Firmware
File.
Start the USB Update again.
This unit automatically retries the
request several times. Wait until the
Display stops. If the Display stops at the
Error display, press and hold the "Power
operation" button for 5 seconds.
This unit automatically retries the
request several times. Wait until the
Display stops. If the Display stops at the
Error display, press and hold the "Power
operation" button for 5 seconds.
This unit automatically retries the
request several times. Wait until the
Display stops. If the Display stops at the
Error display, press and hold the "Power
operation" button for 5 seconds.
This unit automatically retries the
request several times. Wait until the
Display stops. If the Display stops at the
Error display, press and hold the "Power
operation" button for 5 seconds.
Disconnect and reconnect the USB
memory.
Make sure that the Firmware File is in
the USB memory.
Make sure that the model name and
area are supported by the Firmware
File.
This unit automatically retries the
request several times. Wait until the
Display stops. If the Display stops at the
Error display, press and hold the "Power
operation" button for 5 seconds.
Disconnect and reconnect the USB
memory.
Make sure that the Firmware File is in
the USB memory.