Long Term Storage; Ordering Replacement Parts - Land Pride RC5020 Series Operator's Manual

Section 5: Maintenance & Lubrication
Inspection
Inspect all parts for excessive wear and condition. Clean
all parts that do not require replacement.The original
friction disk thickness is 1/8" (3.2mm) and should be
replaced if thickness falls below 3/64" (1.1mm). If
clutches have been slipped to the point of "smoking" , the
friction disks may be damaged and should be replaced.
Heat build-up may also affect the yoke joints.
Assembly
Reassemble each friction disk (#4) next to the metal plate
it was separated from. Install bolts (#3) through the end
plates and intermediate plates as shown. Place springs
(#2) over the bolts and secure with nuts (#1).
Refer to Figure 5-16:
Progressively tighten each spring retainer bolt until
correct spring height "A" is reached.
Driveline Driveline
Take-Off
No. Location
826-819C Wing 540/1000
826-820C Center 540/1000
Clutch Adjustment
Figure 5-16
Long-Term Storage
Clean, inspect, service, and make necessary repairs to
the cutter when storing it for long periods and when
storing it at the end of a working season. This will help
ensure the cutter is ready for field use the next time you
hook-up to it.
!
DANGER
To avoid serious injury or death:
• Always disconnect driveline from the tractor before
servicing the drivetrain and components powered by the
drivetrain. A person can become entangled in the drivetrain
if the tractor is started and the power take-off is engaged.
• Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
11/13/18
Table of Contents
Power
Cat. A"
No. Spring Height
Speed
5 1.32" (3.4 cm)
5 1.32" (3.4 cm)
1. Clean off any dirt and grease that may have
accumulated on the cutter and moving parts. Scrape
off compacted dirt from the bottom of deck and then
wash surface thoroughly with a garden hose. A
coating of oil may also be applied to the lower deck
area to minimize oxidation.
2. See "Cutter Blades" on page 43. Check blades and
blade bolts for wear and replace if necessary.
3. Inspect for loose, damaged, or worn parts and adjust
or replace as needed.
4. Repaint parts where paint is worn or scratched to
prevent rust. Ask your Land Pride dealer for aerosol
touch-up paint. Paint is also available in touch-up
bottles with brush, quarts, and gallon sizes by adding
TU, QT, or GL to the end of the aerosol part number.
Land Pride Touch-up Paint
Part No. Part Description
821-011C PAINT LP BEIGE SPRAY CAN
821-054C PAINT MEDIUM RED SPRAY CAN
821-058C PAINT GREEN SPRAY CAN
821-066C PAINT ORANGE SPRAY CAN
821-070C PAINT GP GLOSS BLACK SPRAY CAN
5. Replace all damaged or missing guarding & decals.
24600
6. Lubricate as noted in "Lubrication Points" starting
on page 50.
7. Store cutter on a level surface in a clean, dry place.
Inside storage will reduce maintenance and make for
a longer cutter life.
8. Follow all unhooking instructions on page 25 when
disconnecting tractor from cutter.

Ordering Replacement Parts

Land Pride offers equipment in factory standard Beige
with black highlights. This implement may also be
purchased in Orange, Green, or Red.
When ordering an optional color, the suffix number
corresponding to the color must be added at the end of
the part number. Parts ordered without the suffix number
will be supplied in factory standard colors.
81 . . . . . . . Green
82 . . . . . . . Orange
83 . . . . . . . Red
For example, if you are ordering a replacement part with
part number 555-555C and the existing part is orange,
then add the suffix 82 to the end of the number to make
the part number read 555-555C82.
RC(M)5020 Series 2 (S/N 1316082+) Rotary Cutter 334-437M
85 . . . . . . . Black
86 . . . . . . . Yellow
49