Pax Technology PX5 Installation Manual

PAX TECHNOLOGY INC.
Product Description Product Description
Cable retention
cover plate
Communication
ports - located
Stylus pen under cover plate
Touch screen
and
Speakers
Contactless
reader area Regulatory label
Part number/
Magnetic
serial number label
stripe reader
Communication
module
MAC address label
Privacy shield
Keypad
Communication ports are labeled and color-coded:
Smart card
reader
White Red Yellow Black Blue
PAX TECHNOLOGY INC.
Communication Module Communication Module Power Connections Power Connections
3
x Power can be supplied via the power port or a single data cable
P terminals that include a default communication module come
that carries power. This power can be provided via a "powered
standard with one Ethernet port and RS232, USB, and PUSB
cable" where the connected POS terminal provides the power
network capabilities. However, if the default communication
(i.e. PUSB or Power over Ethernet) or by connecting a P power
module is replaced with an optional communication module,
supply directly to the data cable (i.e. RS232 or USB).
your choice of these additional network capabilities are
1) Power Port
available:
Insert the power connector into the green POWER port. Turn
the power connector, locking the tab behind the short plastic
• A second Et hernet port • Wi -Fi and Bl uetooth LE
wall. Dress the cable through the retention clips. A separate
• Po we r over Et hernet • Wi -Fi and Ce llular GS M
data cable is also required.
• An Et hernet hub
2) POS Cable
The commu nication mo dule is located on the underside of
Insert the cable connector into the appropriate port on the
the termi nal.
terminal. Dress the cable through the retention clips opposite
the port. Connect power supply to cable as required. The cash
register could also supply power to terminal.
3) Power over Ethernet (PoE)
Power is available over the red LAN1 port when the optional
PoE communication module is installed.
Cable Retention Cover Plate
After power and data cables are
Communication
connected and dressed through
module
retention clips, install the cable
retention cover plate and secure
with captive screw.
WARNING:
Power down and remove all power from the terminal before
Working Environment: Temperature -10°C～50°C (14°F～122°F)
Green removing or installing a communication module. A
communication module must be installed before power can be
Storage Environment: Temperature -20°C～60°C (-4°F～140°F)
applied to the terminal.
PAX TECHNOLOGY INC.
Stylus Holder and Pen Stylus Holder and Pen
4
1) Align stylus holder over
metal screw openings at left
side or top of terminal. Insert
tabs into indentations along
1)
x edge. Attach with captive
Mo unting
Locations
screws.
2) Insert connector end of
stylus pen into stylus port on
2)Stylus Port 3)
left side of terminal.
Re tention
Cl ips 3) Use enclosed plastic card to
press stylus cord into retention
clips on left side of terminal.
Privacy Shield Privacy Shield
5
Insert tabs and snap shield firmly in place
to left and right of keypad. Not designed to
be removable. Removing the shield breaks
the retention tabs and the ability to remotely
track the status of the shield is lost.
Screw
Decorative Plug – If a privacy shield is not
1Privacy Shield
installed, a non-removable decorative plug
may be installed in its place. This plug does
not provide any PIN entry privacy.
R.H.: 10%～93% (non-condensing) CAUTION: If the privacy shield is not installed,
you must use PCI-approved alternative methods
Decorative Plug
R.H.: 5%～95% (non-condensing) to secure the PIN pad.
PAX TECHNOLOGY INC.
Plugs Plugs
Reset Button and Audio Jack Reset Button and Audio Jack
6
7
1) Stylus Holder Plug
If required, restart the
If required, to prevent stylus pen from
terminal by pressing in
being inserted vertically into stylus
and holding the reset
holder, firmly insert plug into opening
1) Stylus button for 2-3 seconds
in holder, aligning with curve of stylus
Holder
Plug
holder.
If required, a visually disabled person can connect a
2) Smart Card Reader Plug
headphone to the terminal for audio prompting using the
If required, insert smart card reader
3.5mm output audio jack.
plug into smart card receptacle slot.
Cable Lock Cable Lock
To remove, if required, gently pry out
8
the plug using a small screwdriver in
the slit along top of plug.
3) Ethernet Plug If required, insert customer-provided
An Ethernet plug is included in case cable lock into K-Slot®. Loop cable
2) Smart Card Reader Plug
around permanent object to secure
you want to block an inactive LAN port.
Align plug so that it matches the shape in place.
of the port and gently push into opening.
To remove, if required, gently pry off
using a small screwdriver in the slit
along the top of the plug.
3) Ethernet
Note: LAN2 port is enabled only when
Plug
Ethernet hub or PoE and Ethernet hub
communication module is installed.
Stand Installation Stand Installation
9
If required, the P terminal may be x
Audio Jack
Reset mounted to a stand.
Button
Instructions may vary depending
Route
on stand specifications.
Stylus Port Cables
Carefully route the required cables
up through the stand pipe and out
the top. Connect the cables to the
P terminal ports. x
Insert the three mounting slots on
the underside of the terminal into
the three metal prongs on the stand
base.
Mounting
Slots
Slide the terminal firmly into position,
locking the terminal in place on the
stand. Secure with fastening screw
or locking device as required.