Table of Contents
Advertisement
Quick Links
Installation Instructions
PowerBoard
Automatic Retracting Running Board
Installation Tips
Read and follow, precisely, all installation instructions provided when
installing this product. Failure to do so may result in a poor fit, and could
place occupants of the vehicle in a potentially dangerous situation.
WARNING
The manufacturer strongly recommends that this product be
professionally installed.
WARNING
Failure to carefully follow the electrical installation steps
could result in severe electrical shock which could harm the installer and/or damage
the vehicle.
WARNING
This product is designed primarily to enhance the appearance
and comfort of the vehicle. Do not rely in any way on the components of this product
to protect the occupants within the vehicle, or to protect against injury or death in
the event of an accident. Never operate the vehicle in excess of manufacturer's
specifications.
WEAR SEAT BELTS AT ALL TIMES
Tools
5mm Allen Wrench
Safety Glasses
1/8" Drill
Drill- Driver
3/8" Drill
P1 - 75152 Rev. C 0416
®
10mm Wrench
Installation Instructions - PowerBoard
Installation Time
4 Hours
Skill Level
4 - Difficult
®
Vehicle Application:
Jeep Wrangler Unlimited
Part Number 75152-15
Support
We're here to help!
Gto to
http://www.Bestop.com
and click "Ask a Question"
© 2016 Bestop, Inc.
2007- 2016
Advertisement
Table of Contents
Summary of Contents for Bestop PowerBoard 75152-15
- Page 1 Gto to http://www.Bestop.com 5mm Allen Wrench Safety Glasses 10mm Wrench and click “Ask a Question” Skill Level 1/8” Drill Drill- Driver 3/8” Drill 4 - Difficult P1 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
-
Page 2: Parts List
Part # 470.03 Qty. 4 Torsion Bar Left- Driver 11” Cable Tie Part # 525.22 Part #470.02 Light Qty.1 Qty. 2 Part #470.15 Qty. 4 P2 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®... -
Page 3: Miscellaneous Hardware
Socket Cap Screw Part # 470.00 Qty. 8 Miscellaneous Hardware Torsion Bar Collar Drill Template Part # 517.95 Part # 523.18 Qty. 4 Qty. 1 P3 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®... - Page 4 6. Now tighten linkages to the Jeep body and Welded Body Flange. Torque all fasteners to the following specifications: 5-7 ft-lbs (6.79-9.40 NM / 60-84 in-lbs) Do not exceed 7 ft-lbs. P4 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 5 Failure to do so could result in severe electrical shock which could harm the installer and/or damage the vehicle. P5 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 6 Secure the harness to the firewall and frame using the #460.99 7” cable ties. P6 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 7 Slit the rubber grommet in the floor. Passenger side shown. Thread the trigger wires through the grommet and into the passenger compartment. P7 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 8 You will need to install the motor and test each wire until you find the wire that functions properly. P8 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 9 Only tighten the screws Repeat on the Right (Passenger) side of the vehicle. holding the Idler Linkages to the vehicle finger tight at this time. P9 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 10 Mark the position of the middle hole in the template on the welded body flange. Driver side shown. P10 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 11 Nut through the hole in each collar. Tighten the WARNING Only tighten screws holding screw before tightening the Nylon Lock Nut. the Motor Linkage to the vehicle finger tight at this time. P11 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 12 Secure loose wires with the 7” Cable Ties as necessary. Driver side shown. Repeat on passenger side of the vehicle. P12 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
- Page 13 Close the doors to retract the linkages. Refer to Page 4 of this guide for instructions on the order of tightening fasteners and torque specifications. P13 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®...
-
Page 14: Powerboard® Troubleshooting
You can also shut the door latch with the door open by pushing on the latch catch with a screwdriver. P14 - 75152 Rev. C 0416 © 2016 Bestop, Inc. Installation Instructions - PowerBoard ®... -
Page 15: Care And Maintenance
For further information or request for warranty work, please contact: Bestop Inc., Customer Service Toll-Free: (800) 845-3567 Main: (303) 465-1755 E-mail: csbestop@Bestop.com Website: www.Bestop.com P15 - 75152 Rev.