Advertisement
V5852A, V5853A, V5862A, V5863A CARTRIDGE GLOBE VALVES
1/4
V5852/V5862
(7)
B
A
1/4
V5853/V5863
(7)
B
B
A
Fig. 2. Dimensions of Series 1000 and 2000 V5852A, V5853A, V5862A and V5863A Valves in in. (mm).
Fig. 3. Removing protective cover from valve.
OPERATION
The valves are supplied with a threaded plastic protective
cover/manual handle to protect the stem and to allow for
manual operation. Use the protective cover/manual
handle to fill the system during initial installation.
Turning the protective cover/manual handle:
— Clockwise: pushes the center stem of the valve down,
compressing the valve spring and closing the valve.
— Counterclockwise: allows the spring to expand,
pushing the center stem up and opening the valve.
NOTES:
—
You can also use the protective cover/handle
for heating/cooling with neither a controller
nor actuator during building construction.
—
Retain the protective cover. It can be needed
for future manual operation.
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
FLOW DIAGRAM
STROKE
1-3/16 (30)
23/32
(18)
INLET
C
B
D
FLOW DIAGRAM
STROKE
1-3/16 (30)
23/32
(18)
PORT A
D
E
B
C
M8228A
By using this Honeywell literature, you agree that Honeywell will have no liability for any
damages arising out of your use or modification to, the literature. You will defend and
indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or
damages, including attorneys' fees, arising out of, or resulting from, any modification to the
literature by you.
VALVE
SIZE
1/2 (13)
2-1/3 (60)
3/4 (19)
3-2/9 (82)
OUTLET
V5853 (SWEAT)
VALVE
SIZE
1/2 (13)
2-1/2 (63)
PORT AB
3/4 (19)
3-2/9 (82)
V5863 (NPT)
VALVE
PORT B
SIZE
1/2 (13)
2-5/7 (69)
3/4 (19)
3-2/9 (82)
NOTE: SOLDER ENDS CONFORM TO ANSI B16-18.
Two-Way Valve Flow
In the two-way valves, the direction of flow is always from
inlet port to outlet port as indicated by the arrows on the
valve body (see Fig. 4).
OUTLET
Fig. 4. Two-way valve operation block diagram.
Three-Way Valve Flow
Three-way valves are designed as mixing valves. This
means that port AB is total flow outlet; port A is controlled
flow inlet; and port B is bypass inlet (see Fig. 5).
AB
Fig. 5. Three-way valve operation block diagram.
® U.S. Registered Trademark
© 2013 Honeywell International Inc.
62-0202—02
M.S. Rev. 02-13
Printed in United States
B
C
A
(NPT)
1-1/3 (34)
1/2 NPT
3/4 NPT
1-1/4 (32)
B
A
C
NPT
1-1/6 (30)
1-1/3 (34)
5/6 (21)
1-4/7 (40)
1-2/7 (33)
1 (27)
B
A
C
NPT
1-1/4 (32)
1-1/3 (34)
1/2 NPT
1-3/5 (41)
1-2/7 (33)
3/4 NPT
INLET
+
–
+
–
AB
A
B
D
D
(NPT)
(SWEAT)
1/2 NPT
5/8 (16)
3/4 NPT
7/8 (22)
E
D
(SWEAT)
5/8 (16)
7/8 (22)
E
D
(NPT)
1/2 NPT
3/4 NPT
M34543
INLET
+
–
OUTLET
M5357A
+
–
A
B
M5358
Advertisement
