Novatek-electro RS-485 Operating Manual page 14

Sunset time, s
Time of day, ms
Current IP-address of
GSM**
Unused parameter
GSM signal level, %**
Unused parameter
SIM card account status** The account status received on the last USSD request (sent
Time for receiving the SIM
card account value**
User parameters of status User parameters of status after starting take a value of 0. They can be
User parameters of
statistics
Not es:
* – IP-address of device in GSM network can be allocated dynamically. For the access to the device via GSM using
its IP-address, please contact the
** – content of registers is available only in the setting mode.
Table 5.8 – Setting parameters
Range of
Parameter
values
Ethernet network
Static IP-
address IP-address
Subnetwork
IP-mask
mask
Gateway
IP-address
Switch on the
dy-namic
0 – 1
addressing with
a help of DHCP
Switch on the
filter of IP-ad-
0 – 1
dress of DHCP-
server
Switch on the
use of server
0 – 1
gateway DNS
IP-address of
DNS server
IP-address 8.8.8.8
IP-address of
ad-ditional DNS IP-address 0.0.0.0
server
Enable MAC
0 – 1
address
override
Table 5.8 Continued
EM-481
-1: Sunset is not observed on this day;
0–86399: Number of seconds from midnight to sunset;
Number of milliseconds from midnight of the current day
IP-address obtained from GPRS* provider
The parameter is reserved for compatibility
Signal level and quality of radio communication with GSM provider
The parameter is reserved for compatibility
automatically once a day). As an account, the first number in the
operator's response is taken.
-2147483648 – the account status is unknown
The number of seconds from January 1 of the specified year (see reg.
172).
0 – account status was not accepted
used for storage and transmission to the server of values to be
measured and calculated in the values files.
They store the value for the operating time of the built-in battery for
the clock. They can be used in the task files for statistics gathering or
saving state
GSM operator
;
Factory
setting
If the dynamic addressing is switched off or not available, IP-
192.168.0.
address of the device in Ethernet network is equal to this
111
value
255.255.2
It is used only with static IP-address
55.0
It is used only together with static IP-address for
192.168.
communication with other networks, or as an address of
0.1
DNS/DHCP servers
0 - for addressing in Ethernet, the specified values of the IP
address, mask and gateway are used;
1
1 - If DHCP server is available in the network, then IP
address, mask and gateway are received from the server.
It is used for dynamic addressing.
0 - the addressing data from the first responding DHCP
0 server is received;
1 – the device receives addressing data only from DHCP-
server with IP-address of the gateway
It is used if DHCP is not available (switched off):
0: DNS of gateway is not used;
1
1: The gateway DNS is used to determine the IP addresses
of other servers, if they are specified by host names.
It is used if DHCP is not available (switched off);
When the server of DNS gateway is used, it sets IP-address
of additional DNS server
It is used if DHCP is not available (switched off);
0.0.0.0 – it is not used.
0 - unique value for each device is used as MAC address;
0 1 - is used of manually set MAC address.
14
- -
Description
234 – 235
236 – 237
900 – 903
904 – 914
915
916 – 931
932 – 933
934 – 935
5000 –
5219
5220 –
5249
Address
300 – 303
304 – 307
308 – 311
312
313
314
315 –318
319 – 322
323
NOVATEK-ELECTRO