Table of Contents
Advertisement
OPERATING THE RECEIVER
1.1 LNB Setting
You can select the satellite and LNB setting conditions to
execute channel search and you can alter the settings for
22KHz tone. The parameters set in this menu are needed for
programming the channels for the "Auto scanning" and
"Manual scanning".
The necessary information can be found at your antenna and
LNB brochures, or you can ask your dealer.
Select LNB power supply "On".
Select the desired satellite name.
Select the LNB type (frequency).
Select the DiSEqC Mode
(Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B)
Select the switch 0/12V ("0V" or "12V")
If you are using a Positioner, select Positioner DiSEqC1.2 ("Yes" or "No")
22KHz: In case you are using a dual LNB or two antennas connected to a 22KHz tone
switch box, with the 22 KHz tone switch ("On", "Off" or "Auto") you can switch
between both LNB or antennas.
0/12V:
When you use two LNBs or antennas is switched to 0/12V, select what LNB and
antenna are used enable or disable. 0/12V terminal is located on the rear of STB.
1.2 Positioner Setting
If you have a DiSEqC 1.2 motorized system which is fully
compatible with DiSEqC1.2, then you can take advantage
of the DiSEqC 1.2 functions available.
Select Satellite.
Select any transponder from above satellites and
check out the Frequency, Symbol Rate, FEC and Polarity.
In case problems arise, ask your dealer.
Sometimes this transponder may not exist due to broadcasting.
It is better to select main transponder among them for the
desired satellite.
Select from Menu Mode:
"User" mode :
Enables control of basic positioner function
recommended for beginners. General user uses "User" mode.
"Installer" mode : This is used to search for the position of a satellite manually.
20
D
I
G
I
T
A
L
S
1.2.1 User Mode
Select Driving Mode:
You have an option to choose the positioner's movement type:
Continuous, Step or Time.
Select Positioner Slot:
When a Satellite position is set with the positioner which
doesn't have enough slots and the default slot number in
this menu is bigger than a number of slots in a positioner,
Positioner slot in menu can be changed and fit to the number
of slot in a positioner for a Satellite.
Position the antenna with north, south, east and west and
use the
/
/
/
key drives to east,
to south.
If you finished driving of motor, select "Store current Position."
and press
OK
key, to reset new driving motor.
N N o o t t e e
:
The level indicated in the "Signal Status" is only for
reference. The signal quality may be adequate even
though the level indicated is not maximum.
Go to Stored Position.
When the stored position is reached then screen displays "Stop", you can now continue
with the further operations.
Select the Calculate Sat Positions to recalculate the satellite position and
1.2.2 Installer Mode
After checking the positioner's state, installer should use this menu.
He should set the "Disable Limits" before using User mode.
Select the Drive Motor
to drive motor.
key drives to west and
Select "Enable Limit", in order to enable "Set Limit".
Select "Disable Limit", in order to disable "Set Limit".
Select "Reset Positioner" and OK key to reset positioner.
A
T
E
L
L
I
T
E
R
E
C
E
OPERATING THE RECEIVER
key to drive motor.
key drives to west,
key drives to north and
key drives
West/East and use the
/
keys
key drives to east.
21
I
V
E
R
OK
key.
Advertisement
Table of Contents
