Table of Contents
Advertisement
Quick Links
CLIQ.mini Installation and Setup Guide
Last modified: 04/06/18
Description
The Clare Controls CLIQ.mini controller provides all device
management services, supports all Clare user interface
services, and acts as the gateway to the ClareCloud for system
updates. The controller comes complete with the ClareOS
preloaded. The controller also comes equipped with
Z-Wave Plus™ for controlling your Z-Wave devices, such as
integrated lighting, thermostats, sensors, and door locks.
Note:
Models are subject to change without notice.
WARNING:
Any changes or modifications made to this product
not expressly authorized by the manufacturer could void the
user's right to operate this device.
Unpacking the CLIQ.mini
Remove all contents from the CLIQ.mini packaging and ensure
you have the following items.
•
1 × CLIQ.mini device (p/n CLIQ-MOSM-10)
•
1 × wall mounting kit (p/n 950-5002-0)
o
1 × wall mounting bracket (p/n 200-1838-0)
2 × long screws (8-32 × 5/16") (p/n 100-1834-0)
o
2 × short screws (6-32 × 3/4") (p/n 100-1849-0)
o
•
1 × PoE (Power over Ethernet) injector with power supply
(p/n 500-1825-0)
•
1 × paper clip (p/n 999-1852-0)
•
1 × Cat6 Ethernet cable (p/n 300-I894-0)
•
1 × CLIQ.mini Quick Start Guide (CC-DOC-1284)
•
1 × Additional Tips Insert (CC-DOC-1285)
•
5 × UUID/Mac identification labels (CC-DOC-1318)
WARNING:
Do not apply power to the CLIQ.mini until
installation is complete. Failure to do so may result in bodily
injury and/or damage to the equipment.
© Clare Controls, LLC.
Installation
We recommend placing the CLIQ.mini in an open centrally
located area within the home, using the included wall mount to
attach the CLIQ.mini to a standard single gang box.
The CLIQ.mini should not be mounted in a structured
enclosure, panel, or closet. If the CLIQ.mini is placed in a
closed off area, the wireless signal strength may be
compromised.
Note:
To prevent radio frequency (RF) interference, we
recommend that you place the CLIQ.mini away from devices
that may cause interference and away from grounded metals.
Figure 1: CLIQ.mini rear connections
(1) Recessed push button
(2) 2 USB ports
(3) Wire routing channel
1 / 7
Figure 1
(4) Wall mount slots
(5) Micros USB port
(6) Ethernet port
Doc ID – 1263 • REV 08
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Clare Controls CLIQ.mini
Summary of Contents for Clare Controls CLIQ.mini
- Page 1 CLIQ.mini to a standard single gang box. The CLIQ.mini should not be mounted in a structured enclosure, panel, or closet. If the CLIQ.mini is placed in a closed off area, the wireless signal strength may be compromised.
- Page 2 PoE or the included 5v micro USB adapter. WARNING: You must follow the instructions below to power your CLIQ.mini. Failure to do so may result in bodily injury and/or damage to the equipment. Connecting power to the CLIQ.mini To connect power to the CLIQ.mini using PoE using LAN:...
- Page 3 To connect power to the CLIQ.mini using PoE using Wi-Fi: Figure 3: CLIQ.mini PoE Wi-Fi connection Note: PoE with Wi-Fi connection requires an Ethernet cable and an existing Wi-Fi source. Plug an Ethernet cable (#1) into the Ethernet port on your CLIQ.mini.
- Page 4 Connect the power supply’s plug end into a wall outlet. See Figure 4, items 2 and 3. CLIQ.mini ClareHome setup Check the LED on the top edge of the CLIQ.mini. It After the CLIQ.mini’s installation, setup the connection. flashes red until Wi-Fi is configured. See Figure 7, item 1.
- Page 5 (3) Wall mount (6) CLIQ.mini Understanding LED colors and the CLIQ.mini status The CLIQ.mini has LED indicators that change colors based on the CLIQ.mini’s status. Once powered on, observe the CLIQ.mini’s LED status. Figure 7 identifies the LEDs on the CLIQ.mini.
- Page 6 Remove the paper clip and observe the LED behavior. The CLIQ.mini’s LED indicators alternate red and blue signifying it has entered the reboot state. Once the CLIQ.mini boots and the LED flashes red in .5 second intervals, it is in AP mode. Continue with installation and setup.
- Page 7 Warranty information Clare Controls offers a three (3) year limited warranty on original Clare Controls components, from the date of shipment from Clare Controls. To view complete limited warranty details, including limitations and exclusions, www.clarecontrols.com/warranty.
Need help?
Do you have a question about the CLIQ.mini and is the answer not in the manual?
Questions and answers