LockState RemoteLock LS-5i User Manual
  1. Manuals
  2. Brands
  3. LockState Manuals
  4. Locks
  5. RemoteLock LS-5i
  6. User manual

LockState RemoteLock LS-5i User Manual

Electronic deadbolt & lever lock
Hide thumbs

Advertisement

Table of Contents

ELECTRONIC DEADBOLT & LEVER LOCK
LS-5i USER MANUAL
1
6
Attention: Please do not use an "electronic screwdriver" for installation
®
3
2
4
5
8
7
9
0
3
2
4
1
5
8
7
9
6
0

Advertisement

Table of Contents
loading

Related Manuals for LockState RemoteLock LS-5i

Summary of Contents for LockState RemoteLock LS-5i

  • Page 1 ® ELECTRONIC DEADBOLT & LEVER LOCK LS-5i USER MANUAL Attention: Please do not use an “electronic screwdriver” for installation...

  • Page 2: Installations Instructions

    INsTALLATIONs INsTRuCTIONs 1. CONfIguRE LATCh BACKsET the BACKSet is the distance between the center of cross bore and edge bore of the door. Adjustable latch fits both BACKSET of 2-3/8” (60mm) and 2-3/4” (70mm). Please follow the steps shown below for BACKSET adjustment.

  • Page 3: Install Latch

    2. IDENTIfy DOOR hANDINg Face the door from outside, the door is left-handed if the hinge is on the left-hand side of the door, whereas the door is right-handed if the hinge is on the right-hand side of the door. inteRioR DooR HinGe...
  • Page 4 5. INsTALL KEyPAD AssEMBLy DEADBOLT KEYPAD ASSEMBLY ensure the latch bolt is retracted. Please refer to diagram B for cylinder installation. Place deadbolt against keypad with tailpiece in horizontal position inserted through hub of iC wiRe the latch. Pass the iC wire under the CYLIndER latch to the interior side of the door.

  • Page 5: Battery Cover

    7. INsTALL RECEIVER MODuLE DEADBOLT RECEIVER INSTALL Adjust turn piece as shown in diagram A. Remove the battery cover (push it up and pull it out). Connect the IC wire then attach receiver module to the door with screws. It’s optional to use the included wood screw (wood screw only for wood doors).

  • Page 6: Install Batteries

    8. INsTALL BATTERIEs BAtteRY Insert 4 AA Alkaline or Lithium batteries CovER and put the battery cover back on the receiver module. do not use rechargeable (niCd, niHm, LiPo, etc.) batteries or batteries with a voltage rating of under/over 1.5v * Please note: deadbolt model will not function until door handing is programmed on the lock (pg.8)

  • Page 7: Battery Holder

    LOCK OVERVIEW LoCKSTATE BuTTon The LockState Button is utilized for entering codes and setting functions. It’s also a lock button. nUmBeR BUttonS Input buttons for codes and function programming. CYLIndER Lock/unlock the lockset from exterior. GASKet Prevent water permeating into lockset.

  • Page 8: Specifications/Functions

    The lockset will become unlocked by key, by entering a user/local code followed by LockState on the keypad, or by interior turn knob. Locking the door The lockset will become locked by key, by pressing the LockState button twice, or by interior turn knob.

  • Page 9: Function Programming

    Programming Code (default: 123456) Local Code fuNCTION PROgRAMMINg Remote Button SET DOOR HANDING (Deadbolt only) noTE: Place deadbolt in the “unlocked” position for this step. The lock will not operate until this setting has been programmed during initial setup or after factory reset. Enter PC Lock the Door Unlock the Door...

  • Page 10: Install Lock

    THE LoCK Unlocking the door The lockset will become unlocked by entering a user/ local code on the keypad followed by LockState, by key, or by interior turn knob. Locking the door The lockset will become locked by pressing the Lock- State button twice, by key, or by interior turn knob.

Table of Contents