Error Display And Diagnosis - Whirlpool LSA 1100 Service Manual

ERROR DISPLAY AND DIAGNOSIS

ERROR DISPLAY AND DIAGNOSIS
RID#1 .5 SUPERSOAK
1) Super soak option selection improves the Wash performance whenever the Super soak option selection improves the Wash performance whenever the Super soak option selection improves the Wash performance whenever the
dirt level in the Wash loads found to be higher. dirt level in the Wash loads found to be higher.
2) While selecting this Feature, Soak Duration will get increased While selecting this Feature, Soak Duration will get increased with respect
to Water level and program selected. to Water level and program selected.
RID#1 .6 SOFTENER FILL
1) Softener Valve fill will happen in the Last Rinse Phase of all programs except Softener Valve fill will happen in the Last Rinse Phase of all programs except Softener Valve fill will happen in the Last Rinse Phase of all programs except
P5(Wool), P7(Whites) and P10(Spin). P5(Wool), P7(Whites) and P10(Spin).
2) In Case of P8(Colors) Softener valve fill will Happen even in Was In Case of P8(Colors) Softener valve fill will Happen even in Was In Case of P8(Colors) Softener valve fill will Happen even in Wash Phase
RID#1 .7 DELAY END
1) Delay End key is used to set the "Delay End" time for the selected wash Delay End key is used to set the "Delay End" time for the selected wash Delay End key is used to set the "Delay End" time for the selected wash
program
2) Delay End option can be selected between 3 to 24 Hrs Delay End option can be selected between 3 to 24 Hrs
3) While selecting this feature, control will While selecting this feature, control will complete the selected cycle in the Specified
duration of Delay
RID#2 ERROR DISPLAY & ITS DIAGNOSIS ERROR DISPLAY & ITS DIAGNOSIS
RID#2.1 CHECK WATER ERROR .1 CHECK WATER ERROR
1) If desired water level did not attain within 10 mins during fill then Check Water Error If desired water level did not attain within 10 mins during fill then Check Water Error If desired water level did not attain within 10 mins during fill then Check Water Error
will be popped by means of turning ON the Check water LED. will be popped by means of turning ON the Check water LED.
2) Inlet valve will move to Inlet valve will move to OFF state after 5 mins from Check water error
detection & waits for start key press after checking the water inlet. detection & waits for start key press after checking the water inlet. detection & waits for start key press after checking the water inlet.
3) Need to check:
OFF state after 5 mins from Check water error
a) Ensure the Water supply at the inlet e the Water supply at the inlet
b) Check for the blockage at fill hose and at the Inlet valve filter. Check for the blockage at fill hose and at the Inlet valve filter. Check for the blockage at fill hose and at the Inlet valve filter.
c) Ensure that Inlet v Ensure that Inlet valve is turning ON during fill process and if not check for
inlet valve operation & its connections from PCB to Inlet valve. inlet valve operation & its connections from PCB to Inlet valve. inlet valve operation & its connections from PCB to Inlet valve.
d) Check for pressure sensor frequency response & kink or puncture at the Check for pressure sensor frequency response & kink or puncture at the Check for pressure sensor frequency response & kink or puncture at the
pressure hose. pressure hose.
e) Ensure that drain hose free end should be lef Ensure that drain hose free end should be left in atmosphere not in any other
medium.
f) Ensure that the Water head is >10ft from the Machine Inlet. Ensure that the Water head is >10ft from the Machine Inlet. Ensure that the Water head is >10ft from the Machine Inlet.
g) Check for functionality of both COLD & SOFTENER VALVE. Check for functionality of both COLD & SOFTENER VALVE. Check for functionality of both COLD & SOFTENER VALVE.
complete the selected cycle in the Specified
alve is turning ON during fill process and if not check for
SERVICE MANUAL
with respect
t in atmosphere not in any other
Page | 20