Advertisement
Basic operation - Baby unit
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off your baby unit.
8
9
10
Overview - Parent unit
Zoom /
Back
LCD ON/OFF
Microphone
11
LED lights
Arrow keys
12
MENU/SELECT
On/off
TALK
VOL -
VOL +
Speaker
Power jack
Stand
Overview - Baby unit
Light sensor
1
Speaker
5
Camera
2
Antenna
6
ON/OFF
Infrared LEDs
3
LED light
8
Temperature
7
Microphone
4
sensor
ON/OFF
9
switch
Power Jack
10
11
Threaded socket
PAIR
12
5
6
7
Sound activation
When the baby unit detects no sound, the parent
unit screen stays off to save power. Once a sound is
detected, the parent unit screen turns on automatically.
It will then turn off again after 50 seconds of no sound
detection.
Night vision
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare
on your parent unit screen as the baby unit
is adapting to the dark environment.
• When the infrared LEDs are on, the images
are in black and white. This is normal.
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
colors and backgrounds, the display
resolution may vary. Adjust the baby unit's
angle or place the baby unit at a higher
level to prevent glare and blurry display.
Mount the baby unit (optional)
Note
NOTES
NOTE
If you drill the holes into a stud, go to step 3.
-OR-
• Check for reception strength and camera
If you drill the holes into an object other than a
angle before drilling the holes.
stud, insert the wall anchors into the holes. Tap
Use a pencil to mark two holes in parallel.
gently on the ends with a hammer until the wall
Make sure they are the same distance apart
anchors are flush with the wall.
as the wall mount holes on the baby unit.
Insert the screws into the holes and tighten
Align the wall mount bracket and screws with
the screws until only 1/4 inch of the screws are
the holes in the wall as shown. Tighten the
exposed.
screw in the middle hole first, so that the wall
mount bracket position is fixed. You can tighten
the other screw in the top hole.
Place the baby unit on the wall mount bracket.
Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket at
Tighten the screw into the threaded socket at the
the bottom to secure the baby unit.
bottom to secure the baby unit. Align the holes
on the wall mount bracket with the screws on the
wall, and slide the wall mount bracket down until
it locks into place.
You can maximize your baby unit's viewing angles by tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the
wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint and secure the angle.
For VM3261-2 only
Status check - Two baby units
If you are viewing baby unit
, the POWER LED light of baby unit
turns on.
As baby unit
is not being viewed, its POWER LED light flashes.
NOTE
Note
NOTES
• If you power on only one baby unit, your parent unit may display
and the LINK LED light flashes.
Press
to switch to the baby unit you have powered on.
Change different views - Patrol
Press MENU when the parent unit is idle. Press
or
to choose
, then press SELECT or .
Press
or
to choose
, then press SELECT to confirm your selection.
10s
Change different views - Single-cam
Press
to switch to another camera in SINGLE-CAM mode.
Press
.
Advertisement
