GE Druck DPI611 Quick Start Manuals
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Test Equipment
  5. Druck DPI611
  6. Quick start manuals

GE Druck DPI611 Quick Start Manuals

Portable pressure calibrator
Hide thumbs Also See for Druck DPI611:

Advertisement

Table of Contents

See also: User Manual
GE
Measurement & Control
Druck DPI611
Portable Pressure Calibrator
Safety and Quick Start Guide – K0565
DPI611: Pressure Calibrator (Figure 1)
Maximum Operating Pressure: As stated on Range
Label at the back side of Calibrator.
Over pressure limited to 1.5 × MWP
Note: MWP is based on Unit pressure range
Operating Temperature Range:
-10 °C to +50 °C (+14 °F to +122 °F)
+10 °C to +30 °C (optimized calibration specification)
0 °C – 40 °C with optional mains power supply
Storage Temperature: -20 °C to +70 °C (-4 °F to +158 °F)
Humidity: 0 to 90 % Relative Humidity (RH)
Non-condensing
Power Supply: 100 – 260 V +/-10 %, 50 / 60 Hz AC,
Output DC V=5 A, 1.6 A, CATII of IEC60364-4-443
Pressure Ranges:
+/-1 barg (-14.5 to 15 psig)
-1 to 2 barg (-14.5 to 30 psig)
-1 to 7 barg (-14.5 to 100 psig)
-1 to 10 barg (-14.5 to 150 psig)
-1 to 20 barg (-14.5 to 300 psig)
Accuracy 10 °C to 30 °C, 1 yr. 0.025 % FS
Add 0.001 % FS/°C outside 10 °C to 30 °C
Altitude: Up to 2000 m
Pollution Level: Degree 2
Batteries (Primary): 8 × AA Alkaline
*Caution: To prevent damage to the DPI611, only use
it within the specified pressure limit on the label.
© 2014 General Electric Company. All rights reserved.
Trademarks
All product names are trademarks of their respective companies.

Advertisement

Table of Contents
loading

Related Manuals for GE Druck DPI611

Summary of Contents for GE Druck DPI611

  • Page 1 Measurement & Control DPI611: Pressure Calibrator (Figure 1) Maximum Operating Pressure: As stated on Range Druck DPI611 Label at the back side of Calibrator. Over pressure limited to 1.5 × MWP Note: MWP is based on Unit pressure range Portable Pressure Calibrator Operating Temperature Range: -10 °C to +50 °C (+14 °F to +122 °F)
  • Page 2 Figure 1 International Language Index: ..................NGLISH Customer service ..................RENCH ..................Visit our web site: www.ge-mcs.com ERMAN .................... TALIAN ..................PANISH ................. ORTUGUESE ..................USSIAN ..................HINESE ..................... REEK .................... ZECH ..................ANISH .................. UNGARIAN ................... ITHUANIAN ..................ATVIAN ..................

  • Page 3: Parts List

    ARTS LIST Item Description ON or OFF button; See “Quick Reference”. Pump mechanism. Pneumatic volume adjuster. Test port: To attach the device under test; See Figure 2. Pneumatic pressure release valve to release pressure in the system. CH1 connectors for: Voltage (V); Current (mA+, mA-); Switch operation.

  • Page 4: Quick Reference

    DPI611 P RESSURE DATA Table 2: Pressure Data Range +/-1 barg (-14.5 to 15 psig) -1 to 2 barg (-14.5 to 30 psig) -1 to 7 barg (-14.5 to 100 psig) -1 to 10 barg (-14.5 to 150 psig) -1 to 20 barg (-14.5 to 300 psig) Pressure Leak rates: 7 bar and above = 10 mbar/min Vacuum Leak rates:...
  • Page 5 ELECTRICAL WARNINGS  To prevent electrical shocks or damage to the instrument, do not connect more than 30 V between the terminals, or between the terminals and the ground (earth).  This instrument uses standard AA size batteries. To prevent an explosion or fire, do not short circuit.

  • Page 6: Standard Equipment

    CAUTIONS  To prevent damage to the display, do not use sharp objects on the touch-screen.  Removal of power without appropriately shutting down the DPI611 can lead to loss of date and time; if it happens re-set the date and time upon re-start.

  • Page 7: Installation

    Do not dispose of this product as household waste. Use an approved organization that collects and/or recycles waste electrical and electronic equipment. For more information, contact:  Our customer service department: (Contact us at www.ge-mcs.com). [EN] English –K0565 Issue 1 Safety and Quick start guide 5...
  • Page 8 5. DPI611 P RESSURE ALIBRATOR TART PERATIONS Install the Battery (See Figure 4) 1. Remove the battery cover by unscrewing the Retaining screw (B) and lifting the cover upwards. 2. Remove old batteries and dispose off in accordance with local instructions.

  • Page 9: Basic Modes

    6. B ASIC ODES Power ON From OFF – momentarily press the power button until the GE logo appears. Power ON/OFF Figure 5 Power OFF Press and Release the Power Button: Select SWITCH OFF from the POWERDOWN OPTIONS window displayed.

  • Page 10: Dashboard Navigation

    7. D ASHBOARD AVIGATION The application DASHBOARD allows quick selection of the appropriate function without menus or special keys. The DASHBOARD displays icons representing functional applications of the DPI611, for example, the CALIBRATOR application. Touch the appropriate icon to start the application. When more choices are available than shown on the display, for example, menu lists, swipe a finger up or down, left or right to scroll.
  • Page 11 SETTINGS >> THEME 7.3 Druck DPI611 Manual Select the Help icon on the Dashboard to access the manual. All the information required to operate the Druck DPI611 is in the Help section of the Dashboard which is accessed by selecting: DASHBOARD >>...
  • Page 12 8. R ELEASE THE RESSURE TTACH THE EVICE NDER Step Procedure Release the pressure. Use the applicable adaptor to attach the device; See Figure 9. Figure 9 9. V ACUUM OR RESSURE PERATIONS Figure 10 Step Procedure (Vacuum) Step Procedure (Pressure) Set to vacuum operation Set to pressure operation (-).

  • Page 13: Specification

    Marks and symbols on the instrument Warning – Complies with refer to the European Union manual directives USB ports: Type A; Read the manual Mini-type B connector Ground (Earth) ON / OFF Do not dispose of this product as household waste. See “Maintenance”...
  • Page 14 Safety and Quick start guide 12 [EN] English –K0565 Issue 1...

Table of Contents