SCS TB-9031 User Manual

Workstation monitor checker

Advertisement

Quick Links

USER GUIDE TB-9031
Workstation Monitor Checker
Installation, Operation and Maintenance
Figure 1. SCS CTE701 Workstation Monitor Checker

Description

The SCS CTE701 Workstation Monitor Checker
verifies the proper operation of the SCS
Workstation
Monitor, SCS
Ground
Monitor, SCS
Monitor
and SCS
Ground Man Plus Ground Monitor.
The Workstation Monitor Checker simulates resistance,
impedance and voltage signals so that you can see
whether the response of your monitors complies with
your specifications. It meets the ANSI/ESD S20.20
requirements for compliance verification of continuous
monitors.
The Workstation Monitor Checker presents certain
loads and signals to the monitor that simulate specific
parameters of ground connections and wrist straps.
The Workstation Monitor Checker is available in one
model:
Item
Description
CTE701
Workstation Monitor Checker,
with 9V Alkaline Battery

Packaging

1 Workstation Monitor Checker
1 9V Alkaline Battery
1 Ground Cable (banana to alligator clip)
1 3.5 mm Male to Male cable
TB-9031 Page 1 of 4
August 2015
WS Aware
Ground Master Equipment
Iron Man Plus Workstation
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website:

Features and Components

Figure 2. Workstation Monitor Checker features and
components
The Workstation Monitor Checker uses a 9V alkaline
battery. Make sure that a fresh battery is installed prior
to performing any test. If you are not planning to use
your Workstation Monitor Checker for a long time, please
remove the battery from the device.

Basics

For all tests make sure that:
• Monitor under test is properly grounded and is
operational.
• Disconnect all wires from the monitor under test that go
to the monitored grounds. Leave ground connection of
the monitor connected to a known good ground.
StaticControl.com
Made in the
United States of America
© 2015 DESCO INDUSTRIES, INC.
Employee Owned

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TB-9031 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SCS TB-9031

  • Page 1 • Disconnect all wires from the monitor under test that go to the monitored grounds. Leave ground connection of the monitor connected to a known good ground. SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com TB-9031 Page 1 of 4 August 2015 ©...
  • Page 2 10 ohms should pass at 9 ohms and fail at 11 ohms. SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com TB-9031 Page 2 of 4 ©...
  • Page 3 • After release of “Soft Ground” button the ground monitor shall indicate failure. Allow up to 30 seconds for alarm to trigger for some monitors. SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com TB-9031 Page 3 of 4 ©...
  • Page 4 Meets CE (European Confomity) requirements. Battery Disposal Dispose of batteries in accordance with state and local requirements. SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com TB-9031 Page 4 of 4 © 2015 DESCO INDUSTRIES, INC.
  • Page 5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: CTE701...

Table of Contents