Table of Contents
Advertisement
3-4. FA-TH16X24D31
Item
Number of I/O points, Input device numbers
Insulation method
Rated input voltage/current
Operating voltage range
Maximum number of contacts
simultaneously ON
ON voltage/ON current
OFF voltage/OFF current
Input impedance
OFF→ON
Response time
ON→OFF
Wiring method for common
External power supply
Current consumption
Withstand voltage, insulation resistance
Noise immunity
Operation indication
Terminal block
screw
Terminal block
Applicable wire
Screw
Installation method
DIN rail
Weight
3-5. FA-TH16X100A31L
Item
Number of I/O points, Input device numbers
Insulation method
*1
Rated input voltage/current
Operating voltage range
Maximum number of contacts
simultaneously ON
ON voltage/ON current
OFF voltage/OFF current
Inrush current
Input impedance
OFF→ON
Response time
ON→OFF
Wiring method for common
External power supply
Current consumption
Withstand voltage, insulation resistance
Noise immunity
Operation indication
Terminal block
screw
Terminal block
Applicable wire
Screw
Installation method
DIN rail
Weight
*1: Use a power supply which can be supplied from the secondary side which is isolated by a transformer or converter, etc.
Model
Voltage: 24VDC (CLASS 2), Current: Approx. 10mA (24VDC)
21.6 to 26.4VDC (24VDC ±10% (ripple ratio: within 5%, CLASS 2))
10ms or less (excluding programmable controller response time)
10ms or less (excluding programmable controller response time)
Approx. 27mA when 24VDC (not including current consumption of programmable controller)
(based on noise simulator with noise frequency of 25 to 60Hz)
M3 screw, Number of terminals:36P, 7.62mm pitch, Spring-up screw with finger protection cover
Tightening torque range: 58.8 to 88.2N·cm (6 to 9kgf·cm, 5.22 to 7.5lbf·in),
UL standard conformity tightening torque: 59N·cm, 5.22 lbf·in
22 to 14 AWG: 0.3 to 2.0mm
Tightening torque range: 78 to 118N·cm (8 to 12kgf·cm, 7 to 10lbf·in)
Applicable DIN rail: TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Model
Current: Approx. 8mA (100VAC 60Hz), Approx. 7mA (100VAC 50Hz)
15ms or less(100VAC 60Hz) (excluding programmable controller response time)
35ms or less(100VAC 60Hz) (excluding programmable controller response time)
Approx. 25mA when 24VDC (not including current consumption of programmable controller)
(based on noise simulator with noise frequency of 25 to 60Hz)
Tightening torque range: 68 to 92N·cm(7 to 9kgf·cm, 6.1 to 8lbf·in),
UL standard conformity tightening torque : 80N·cm, 7.08 lbf·in
Tightening torque range: 78 to 118N·cm (8 to 12kgf·cm, 7 to 10lbf·in)
Applicable DIN rail: TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
FA-TH16X24D31
16 points, X0 to XF
Photocoupler
100% (5-directional attachment)
19VDC or higher / 7.9mA or higher
8VDC or lower / 3.3mA or lower
Approx. 2.2kΩ
16 points/common (2-wire type, WET method)
24VDC ±10% (ripple ratio: within 5%, CLASS 2)
560Vrms AC / 3 cycles (altitude: 2000m), 10MΩ or higher
Simulator noise 500Vp-p, noise width 1μs
LED on with power supply ON and input ON
2
(when solderless terminals are used)
M4 × 35mm or more
Approx. 310g
FA-TH16X100A31L
16 points, X0 to XF
Photocoupler
Voltage: 100 to 110VAC (50/60Hz),
85 to 132 VAC (50/60Hz ±3Hz (distortion factor within 5%))
100% (5-directional attachment)
80VAC or higher / 5mA or higher (50Hz, 60Hz)
30VAC or lower / 1.7mA or lower (50Hz, 60Hz)
Max. 200mA within 1ms (132VAC)
Approx. 12kΩ(60Hz), Approx. 15kΩ(50Hz)
16 points/common (2-wire type, WET method)
24VDC ±10% (ripple ratio: within 5%, CLASS 2)
1780Vrms AC / 3 cycles (altitude: 2000m), 10MΩ or higher
Simulator noise 1500Vp-p, noise width 1μs
LED on with power supply ON and input ON
M3.5 screw, Number of terminals:36P, 8mm pitch
20 to 14 AWG: 0.5 to 2.0mm
M4 × 35mm or more
Approx. 320g
11
2
Advertisement
Table of Contents
