Fa-Th16X100A31; Fa-Th16X200A31 - FA goods FA-TH16X100A31 User Manual

3-2. FA-TH16X100A31

Item
Number of I/O points, Input device numbers
Insulation method
Rated input voltage/current *1
Operating voltage range
Maximum number of contacts
simultaneously ON
ON voltage/ON current
OFF voltage/OFF current
Inrush current
Input impedance
OFF→ON
Response time
ON→OFF
Wiring method for common
External power supply
Current consumption
Withstand voltage, insulation resistance
Noise immunity
Operation indication
Terminal block
screw
Terminal block
Applicable wire
Screw
Installation method
DIN rail
Weight
*1: Use a power supply which can be supplied from the secondary side which is isolated by a transformer or converter, etc.

3-3. FA-TH16X200A31

Item
Number of I/O points, Input device numbers
Insulation method
*1
Rated input voltage/current
Operating voltage range
Maximum number of contacts
simultaneously ON
ON voltage/ON current
OFF voltage/OFF current
Inrush current
Input impedance
OFF→ON
Response time
ON→OFF
Wiring method for common
External power supply
Current consumption
Withstand voltage, insulation resistance
Noise immunity
Operation indication
Terminal block
screw
Terminal block
Applicable wire
Screw
Installation method
DIN rail
Weight
*1: Use a power supply which can be supplied from the secondary side which is isolated by a transformer or converter, etc.
Model
Current: Approx. 8mA (100VAC 60Hz), Approx. 7mA (100VAC 50Hz)
85 to 132VAC (50/60Hz ± 3Hz (distortion factor within 5%))
15ms or less (excluding programmable controller response time)
35ms or less (excluding programmable controller response time)
Approx. 25mA when 24VDC (not including current consumption of programmable controller)
(based on noise simulator with noise frequency of 25 to 60Hz)
M3 screw, Number of terminals:36P, 7.62mm pitch, Spring-up screw with finger protection cover
Tightening torque range: 58.8 to 88.2N·cm (6 to 9kgf·cm, 5.22 to 7.5lbf·in),
UL standard conformity tightening torque: 59N·cm, 5.22 lbf·in
22 to 14 AWG: 0.3 to 2.0mm
Tightening torque range: 78 to 118N·cm (8 to 12kgf·cm, 7 to 10lbf·in)
Applicable DIN rail: TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Model
Current: Approx. 7.5mA (200VAC 60Hz), Approx. 6mA (200VAC 50Hz)
170 to 264VAC (50/60Hz ± 3Hz (distortion factor within 5%))
15ms or less (200VAC 60Hz) (excluding programmable controller response time)
35ms or less (200VAC 50Hz) (excluding programmable controller response time)
Approx. 25mA when 24VDC (not including current consumption of programmable controller)
(based on noise simulator with noise frequency of 25 to 60Hz)
M3 screw, Number of terminals:36P, 7.62mm pitch, Spring-up screw with finger protection cover
Tightening torque range: 58.8 to 88.2N·cm (6 to 9kgf·cm, 5.22 to 7.5lbf·in),
UL standard conformity tightening torque: 59N·cm, 5.22 lbf·in
22 to 14 AWG: 0.3 to 2.0mm
Tightening torque range: 78 to 118N·cm (8 to 12kgf·cm, 7 to 10lbf·in)
Applicable DIN rail: TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
FA-TH16X100A31
16 points, X0 to XF
Photocoupler
Voltage: 100 to 110VAC (50/60 Hz),
100% (5-directional attachment)
80VAC or higher / 5mA or higher (50Hz, 60Hz)
30VAC or lower / 1.7mA or lower (50Hz, 60Hz)
Within max. 200mA 1ms (132VAC)
Approx. 12kΩ(60Hz), Approx. 15kΩ(50Hz)
16 points/common (2-wire type, WET method)
24VDC ±10% (ripple ratio: within 5%, CLASS 2)
1780Vrms AC / 3 cycles (altitude: 2000m), 10MΩ or higher
Simulator noise 1500Vp-p, noise width 1μs
LED on with power supply ON and input ON
2 (when solderless terminals are used)
M4 × 35mm or more
Approx. 310g
FA-TH16X200A31
16 points, X0 to XF
Photocoupler
Voltage: 200 to 220VAC (50/60 Hz),
100% (5-directional attachment)
160VAC or higher / 4.8mA or higher (50Hz, 60Hz)
60VAC or lower / 2.3mA or lower (50Hz, 60Hz)
Within max. 500mA 1ms (264VAC)
Approx. 27kΩ(60Hz), Approx. 32kΩ(50Hz)
16 points/common (2-wire type, WET method)
24VDC ±10% (ripple ratio: within 5%, CLASS 2)
2830Vrms AC / 3 cycles (altitude: 2000m), 10MΩ or higher
Simulator noise 1500Vp-p, noise width 1μs
LED on with power supply ON and input ON
2 (when solderless terminals are used)
M4 × 35mm or more
Approx. 320g
10