Uncompressed
Long-Range
Wireless HD Video
The Bolt Pro 300 is a zero
delay wireless video trans�
mission system designed
for the most demanding
cinema, broadcast, and
UAV applications. At less
than 1ms latency, Bolt Pro
can transmit 1080p60 4:2:2
video at up to 300ft line of
sight over the unlicensed
5GHz band.
O
A
B
C
E
D
F
Bolt Pro 300 TX
A:
Video Status
E:
Mini USB Port
B:
Link Status
F:
HDMI Input
C:
Power Status
G:
Power Switch
D:
Fault LED
H:
7-28V DC Input
O
G
G
E
H
H
I
K
J
I
Bolt Pro 300 RX
I:
3G-SDI Output
M:
Menu Joystick
J:
3G-SDI Input
N:
USB 3.0 Port
K:
HDMI Output
O:
Internal Antennas
L:
Link Quality Indicator
ON SCREEN DISPLAY OPERATION
-
Status Screens
Activate the status OSD by depressing the 'Menu Joystick' button (M), and cycle through
screens by pressing these buttons up or down. Hide the status screen by pressing left.
Main Status Screen - This screen displays the status of the wireless receiver, along with the current video
•
resolution, frequency, link quality (if connected).
Time Code Screen - Displays the current time code if received from the transmitter.
•
Temperature Status Screen - Displays the current internal temperature of the unit.
•
300
Menu Operation
-
Launch the menu by pressing right while the OSD is active. Exit from the menu by
pressing left.
HDMI/SDI Out Format - Select the video output format. You can choose to match the video source resolution
•
by selecting 'Same as Input,' or choose from the resolutions listed.
600
Test pattern - Select a video output format from this menu to output a test pattern over HDMI and SDI. Return
•
to the previous video by pressing left on the 'Menu' joystick.
Pairing - Select Pairing to link your receiver with another transmitter. Once pairing is activated on the
•
receiver, turn on the transmitter and use a paper clip to hold the reset button (between the DC input
and power switch) for 1 seconds and release. The red warning LED and link LEDs will blink to
indicate that pairing is active.
OSD Settings - Choose when to display the OSD. By default, the OSD is displayed when the link is down.
•
"Hidden by default" hides the OSD until it is activated by the joystick. If "Always show OSD" is
selected, the OSD will be displayed unless deactivated by the joystick.
Reset All Settings - Use this to reset all configurable options to their factory defaults.
•
Device Info - Displays the model and serial number.
•
CONNECT AND POWER YOUR DEVICE
Connect the output from your video source to the SDI/HDMI input
1
transmitter. Connect either the SDI or HDMI output from the Bolt receiver to the
video input on your monitor.
B
A
Connect power to your Bolt transmitter using the included P-Tap to Lemo cable.
2
Power the Bolt receiver with the included A/C adapter or battery plate accessory. If
L
using the battery plate, connect a compatible battery (AB Gold mount or V-Lock) to
the plate, and connect the short cable from the plate to the receiver's DC input (H).
M
N
Move the power switches on both the transmitter and receiver
3
Video appears within a few seconds.
NEED MORE HELP?
1. Support forum: http://support.teradek.com → Contains tips, information and all the latest firmware & software updates.
2. Training videos: http://www.teradek.com/trainin
TERADEK SUPPORT STAFF:
support@teradek.com or call 888−941−2111 ext2 (Mon−Fri 7am to 6pm PST)
(F)
on the Bolt
(G)
to the ON position.
g
HDMI
SDI
AC adapter
P-Tap to Lemo
Need help?
Do you have a question about the Bolt Pro 300 and is the answer not in the manual?
Questions and answers