Table of Contents
Advertisement
Quick Links
Installation and operating instructions:
Radio-control combined sensor
Type: DALI LS/PD ADVANCED
Customer Service Center (KSC) Germany
OSRAM GmbH
Hellabrunner Str. 1
D-81536 Munich
Tel.: +49 (0) 89 6213 – 0
Fax: +49 (0) 89 6213 – 2020
Albert-Schweitzer-Str. 64
D-81735 Munich
Tel.: +49 (0) 1803 677 – 200
Fax: +49 (0) 1803 677 – 202
www.osram.com
Advertisement
Table of Contents
Related Manuals for Osram DALI LS/PD ADVANCED
Summary of Contents for Osram DALI LS/PD ADVANCED
- Page 1 Installation and operating instructions: Radio-control combined sensor Type: DALI LS/PD ADVANCED OSRAM GmbH Hellabrunner Str. 1 D-81536 Munich Tel.: +49 (0) 89 6213 – 0 Fax: +49 (0) 89 6213 – 2020 Customer Service Center (KSC) Germany Albert-Schweitzer-Str. 64 D-81735 Munich Tel.: +49 (0) 1803 677 –...
- Page 2 Page 2 Installation instructions: Combined Sensor DALI LS/PD ADVANCED...
-
Page 3: Table Of Contents
5. Detection area and shield ..........Page 8 6. Adjustment of the sensor ..........Page 9 7. Lighting control/setpoint adjustment ......Page 9 8. Notes on radio operation ..........Page 11 9. Technical data ..............Page 12 Installation instructions: Combined Sensor DALI LS/PD ADVANCED Page 3... -
Page 4: Function Overview
Sensitivity of the motion detector Delay for switching off the system sens time Abb. B if no movement is detected ot used here. 2 min (The setpoint value is assigned via the manual programming unit) Page 4 Installation instructions: Combined Sensor DALI LS/PD ADVANCED... -
Page 5: Activating The Sensor/Inserting The Batteries
Keep batteries away from children. If a battery is swallowed, seek medical attention immediately. Replace the batteries with ones of the same type. Old batteries should be removed immediately and disposed of properly. Installation instructions: Combined Sensor DALI LS/PD ADVANCED Page 5... -
Page 6: Programming In The Dali Advanced Central Unit
Deleting the device in the DALI ADVANCED central unit: Programmed devices can be deleted via the MPU see the operating instructions for the manual programming unit. Page 6 Installation instructions: Combined Sensor DALI LS/PD ADVANCED... -
Page 7: Installation
Important: Do not attach the combined sensor to the base plate until you have inserted the batteries and programmed the sensor in the central unit. Installation instructions: Combined Sensor DALI LS/PD ADVANCED Page 7... -
Page 8: Detection Area And Shield
Abb. G ∅ approx. 2.20 m Complete shield, area I: ∅ approx. 4.00 m Area II trimmed: ∅ approx. 6.00 m Areas II and III trimmed: ∅ approx. 8.00 m No shield: Page 8 Installation instructions: Combined Sensor DALI LS/PD ADVANCED... -
Page 9: Adjustment Of The Sensor
Activate lighting control by switching the "Regulation" option to "ON". Note: As long as there is a radio link between the central unit and the manual programming unit, lighting regulation will not be carried out. Installation instructions: Combined Sensor DALI LS/PD ADVANCED Page 9... - Page 10 In this case, use one of the suitably programmed channel buttons to switch the lighting system off manually when you leave the room. Page 10 Installation instructions: Combined Sensor DALI LS/PD ADVANCED...
-
Page 11: Notes On Radio Operation
- If used as specified, this device complies with the requirements of the R&TTE directive (1999/5/EU). A complete conformity declaration can be found on the internet at: www.osram.com The combined sensor may be operated in all EU and EFTA states. -
Page 12: Technical Data
42 mm Digital Addressable Lighting Interface The international digital interface standard for the lighting industry Date 13.09.02 / Combined Sensor ADVANCED Version 1.0 Subject to change without notice. Errors and omission excepted. Page 12 Installation instructions: Combined Sensor DALI LS/PD ADVANCED...