Download  Print this page

Siemens CSI Host Driver Installation Instructions

For pxc modular.
Hide thumbs
   

Advertisement

CSI Host Driver for PXC Modular
These installation instructions cover the connection of
the CSI Host Driver to the CSI System. For hardware
installation of the PXC Modular, see document
number 553-638.

Product Description

The CSI Host Driver enables communication
®
between the APOGEE
CSI system.
Product Numbers
PXC00-PE96.A
PXC00-E96.A
PXC100-PE96.A
PXC100-E96.A
PXX-485.3
LSM-INT-CSIHOST
Accessories
538-670
Trunk Interface II, 115V
538-675
Trunk Interface II, 230V
536-004
Modem Cable, DB-9 Female/DB-25
Male, Serial
Item Number: 565-718, Rev. AA
Automation System and the
PXC Modular RS-485 or Ethernet
ALN, 96 FLN nodes
PXC Modular with BACnet/IP
ALN and BACnet MS/TP ALN, 96
FLN nodes
PXC Modular RS-485 or Ethernet
ALN, TX-I/O Support, 96 FLN
nodes
PXC Modular BACnet/IP ALN
and BACnet MS/TP ALN, TX-I/O
Support, 96 FLN nodes
Expansion Module, three RS-485
FLN connections
License for CSI Host PXC
Modular Driver
Installation Instructions
Warning/Caution Notations
WARNING:
Personal injury/loss of life may occur if you
do not follow the procedures as specified.
CAUTION:
Equipment damage or loss of data may
occur if you do not follow the procedures
as specified.
Expected Installation Times
The expected installation time is 30 minutes.
Required Tools and Materials
Flat-blade screwdriver (1/8-inch blade width).
Wire strippers.
Cabling and connectors. See the Connecting
the CSI Host Driver to the CSI System section.
CAUTION:
Always wear an electro-static discharge
wrist strap and discharge accumulated
static before touching field panel
components.
Prerequisites
Driver hardware is installed according to its
respective installation instructions.
FLN Termination blocks installed, if any.
Depending on the type of installation, other
prerequisites may have to be completed.
Document No. 565-718
December 15, 2009
Page 1 of 4

Advertisement

   Related Manuals for Siemens CSI Host Driver

   Summary of Contents for Siemens CSI Host Driver

  • Page 1: Product Description

    December 15, 2009 CSI Host Driver for PXC Modular Warning/Caution Notations These installation instructions cover the connection of the CSI Host Driver to the CSI System. For hardware installation of the PXC Modular, see document WARNING: number 553-638. Personal injury/loss of life may occur if you do not follow the procedures as specified.
  • Page 2 Figure 1 or Figure 2. the CSI System 3. Connect cables per diagram in Figure 1 or Follow these steps to connect the CSI Host Driver Figure 2. to the CSI system: 4. Plug in the power supply for the Trunk Interface II per diagram in Figure 1 or Figure 2.
  • Page 3 9-PIN (MALE) TO 9-PIN (MALE) 9-PIN RIBBON CABLE CSI PART #CBL004 PORT A PORT B 78010 (HOST) TAP TO CSI Figure 2. Connecting the Driver to the CSI System via 78010 (Host) Tap. Page 3 of 4 Siemens Industry, Inc.
  • Page 4 Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners. © 2009 Siemens Industry, Inc. Siemens Industry, Inc.

Comments to this Manuals

Symbols: 0
Latest comments: