Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Joy-it RB-LCD10
Summary of Contents for Joy-it RB-LCD10
- Page 1 10.1“ HDMI LCD...
-
Page 2: Table Of Contents
4.1.2 Rotating the display with touch function Device Connection 5. Usage with a BeagleBone Black Device Connection Installation 6. Usage with a Banana Pi Raspbian OS Device Connection Loading the WiFi-Drivers 7. Support 8. EU-Declaration-of-Conformity Published: 13.06.2018 Copyright by Joy-IT... -
Page 3: Introduction
10.1“ HDMI LCD 1. Introduction Dear customer, thank you for choosing our product. If you encounter any unexpected problems during use, please do not hesitate to contact us. Published: 13.06.2018 Copyright by Joy-IT... -
Page 4: Bracket Mounting
10.1“ HDMI LCD 2. Bracket Mounting Simply follow the illustrated step-by-step instructions below for quick and easy mounting of the bracket. http://anleitung.joy-it.net/wp-content/uploads/2016/12/10.1inch-LCD-Aufbau.jpg Published: 13.06.2018 Copyright by Joy-IT... -
Page 5: Device Connection
(You can also adjust the backlighting of the screen with the "backlight adjustment button", please note the 1 in the following picture.) Published: 13.06.2018 Copyright by Joy-IT... -
Page 6: Usage With A Raspberry Pi
1280 800 60 6 0 0 0 Note: The memory size of your micro SD card should be more than 4GB. In this operation you will also need a micro SD card reader which must be purchased separately. Published: 13.06.2018 Copyright by Joy-IT... - Page 7 /etc/X11/xorg.conf.d Now you have to copy a file in this folder: sudo cp /usr/share/X11/xorg.conf.d/40-libinput.conf /etc/X11/xorg.conf.d When the file has been copied, you must now edit the file for the touch function: sudo nano /etc/X11/xorg.conf.d/40-libinput.conf Published: 13.06.2018 Copyright by Joy-IT...
- Page 8 If you want to have the initial state, you must remove this command again. If you finshed that configuration, the Raspberry Pi needs to be restarted, then the Raspberry Pi should be started with the settings you have set. sudo reboot Published: 13.06.2018 Copyright by Joy-IT...
-
Page 9: Device Connection
4. Insert a micro SD card into the card socket of the Raspberry Pi and then turn on the Pi. After a waiting time you should see the following interface. (Now you can adjust the backlight of the LCD with the "backlight adjustment button". See marker 1 in the following figure. Published: 13.06.2018 Copyright by Joy-IT... -
Page 10: Usage With A Beaglebone Black
Note: If the eMMC of the BeagleBone Black has an operating system installed, you should start the BeagleBone Black from the micro SD card. Do not release the start button until the "User LEDs" start flashing. Published: 13.06.2018 Copyright by Joy-IT... -
Page 11: Usage With A Banana Pi
Compared to the Banana Pi, the BananaPi Pro has an additional WiFi model built in. If you have a BananaPi Pro, you can use SSH as a method to connect it. The following command can be used to load the WiFi drivers: sudo modprobe ap6210 Published: 13.06.2018 Copyright by Joy-IT... -
Page 12: Support
If there are any question left or if you encounter any problems please feel free to contact us by mail, phone or by our ticket-support-system on our website. E-Mail: service@joy-it.net Ticket-System: http://support.joy-it.net Phone: +49 (0)2845 98469 – 66 (11- 18 Uhr) Please visit our website for more informations: www.joy-it.net Published: 13.06.2018 Copyright by Joy-IT... -
Page 13: Eu-Declaration-Of-Conformity
10.1“ HDMI LCD 8. EU-Declaration-of-Conformity Manufacturer: JOY-iT Europe GmbH Pascalstr. 8 47506 Neukirchen-Vluyn Article Name: RB-LCD10 Description Display für Raspberry Pi und andere SBC Purpose of use: Einsatz für Prototyping / Versuchsaufbauten Declares that the product is in compliance with the essential requirements of the following directives when used as intended: 2014/30/EU (EMC) &...
Need help?
Do you have a question about the RB-LCD10 and is the answer not in the manual?
Questions and answers