Linear AP-5 Installation Instructions Manual page 2

– 1 – ADDING TRANSMITTERS
← ENTERS PROGRAM MODE
STEP 1: PRESS PROGRAM FOR 3 SECONDS
← READY FOR PROGRAMMING
DISPLAY: THEN:
← TRANSMITTER ADDING FUNCTION NUMBER
STEP 2: PRESS
← SINGLE TRANSMITTER ID #
STEP 3: PRESS OR STARTING TRANSMITTER
BLOCK ID # (FROM 1-65535)
← ENTERS ID #
STEP 4: PRESS
SKIP TO STEP 6 FOR SINGLE TRANSMITTERS
← ENDING TRANSMITTER
STEP 5: PRESS
BLOCK ID # (FROM 1-65535)
← COMPLETE ID # ENTRY
STEP 6: PRESS
← ENTER "1" FOR TIMED RELAY
STEP 7: PRESS OR
ENTER "0" TO TOGGLE RELAY
NOTE:
REPEAT STEPS 2-7 TO
IF THE TRANSMITTER ID # IS NOT LABELED ON
ADD MORE TRANSMITTERS
A TRANSMITTER, TRIGGER THE TRANSMITTER
TO VIEW THE ID # ON THE AP-5 DISPLAY. USE
← EXITS
THE STAR KEY TO REVIEW THE LAST RECEIVED
STEP 8: PRESS
PROGRAM
ID # (PRESS THE DISPLAY BUTTON TO VIEW
PROGRAM
THE LEFT THREE DIGITS OF THE ID #)
MODE
– 5 – SET TRANSMITTER BUTTONS
USE THESE STEPS TO CHANGE WHICH BUTTONS ON
MULTI-BUTTON TRANSMITTERS WILL ACTIVATE WHICH ACCESS RELAY
← ENTERS PROGRAM MODE
STEP 1: PRESS PROGRAM FOR 3 SECONDS
← READY FOR PROGRAMMING
DISPLAY: THEN:
← TRANSMITTER BUTTON FUNCTION NUMBER
STEP 2: PRESS
(ENTER 21-25: 21 = LEFT; 22 = RIGHT; 23 = TOP;
24 = LOWER LEFT; 25 = LOWER RIGHT)
← ENTER "1" ACTIVATES RELAY K1
STEP 3: PRESS OR
ENTER "2" ACTIVATES RELAY K2
← ENTER "1" TO ENABLE BUTTON
STEP 4: PRESS OR
ENTER "0" TO DISABLE BUTTON
← EXITS PROGRAM MODE
STEP 5: PRESS
PROGRAM
NOTES:
1. THE FACTORY DEFAULT SETTING ONLY ALLOWS THE LEFT TRANSMITTER
BUTTON TO ACTIVATE ACCESS RELAY K1
2. THE BUTTON SETTING WILL BE USED BY ALL TRANSMITTERS PROGRAMMED
3. REPEAT STEPS 2-4 TO PROGRAM OTHER BUTTONS
– 9 – SUSPENDING/ACTIVATING TRANSMITTERS
← ENTERS PROGRAM MODE
STEP 1: PRESS FOR 3 SECONDS
PROGRAM
← READY FOR PROGRAMMING
DISPLAY: THEN:
← TRANSMITTER STATUS FUNCTION NUMBER
STEP 2: PRESS
← TRANSMITTER ID #
STEP 3: PRESS
(FROM 1-65535)
← ENTER "0" TO SUSPEND XMTR
STEP 4: PRESS OR
ENTER "1" TO ACTIVATE XMTR
REPEAT STEPS 2-4 TO SUSPEND OR ACTIVATE ADDITIONAL TRANSMITTERS
← EXITS PROGRAM MODE
STEP 5: PRESS
PROGRAM
NOTES:
1. SUSPENDED TRANSMITTERS CAN NOT TRIGGER ANY ACCESS RELAY, THE
SUSPENDED INDICATOR WILL LIGHT INSTEAD
2. ACTIVATED TRANSMITTERS CAN TRIGGER ANY ACCESS RELAY
– 2 – ADDING AN MGT TRANSMITTER
← ENTERS PROGRAM MODE
STEP 1: PRESS PROGRAM FOR 3 SECONDS
← READY FOR PROGRAMMING
DISPLAY: THEN:
← MGT TRANSMITTER ADDING FUNCTION NUMBER
STEP 2: PRESS
← ENTER "2" FOR RELAY K2
STEP 3: PRESS OR
ENTER "3" FOR RELAY K3
← ENTER "1-6" FOR MGT MEMORY LOCATION NUMBER
STEP 4: PRESS
← MGT TRANSMITTER ID #
STEP 5: PRESS
(FROM 1-65535)
← ENTERS MGT ID #
STEP 6: PRESS
← EXITS PROGRAM MODE
STEP 7: PRESS
PROGRAM
NOTES:
1. IF THE TRANSMITTER ID # IS NOT LABELED ON THE TRANSMITTER, TRIGGER
THE TRANSMITTER TO VIEW THE ID # ON THE AP-5 DISPLAY. USE THE STAR KEY
TO REVIEW THE LAST RECEIVED ID # (PRESS THE DISPLAY BUTTON TO VIEW THE
LEFT THREE DIGITS OF THE ID #)
2. RELAY K1 CANNOT BE PROGRAMMED AS AN OBSTACLE RELAY
3. IF RELAY K2 IS CONFIGURED FOR OBSTACLE, IT CANNOT BE CHANGED BACK
TO ACCESS UNTIL THE ALL MGT TRANSMITTERS SET TO RELAY K2 ARE REMOVED
– 6 – SET FACILITY CODES
USE THESE STEPS ONLY IF TRANSMITTER BLOCKS HAVE BEEN
ORDERED WITH A PRE-SET FACILITY CODE
← ENTERS PROGRAM MODE
STEP 1: PRESS FOR 3 SECONDS
PROGRAM
← READY FOR PROGRAMMING
DISPLAY: THEN:
← FACILITY CODE FUNCTION NUMBER
STEP 2: PRESS
← RECEIVER FACILITY CODE LOCATION (FROM 1-4)
STEP 3: PRESS
← TRANSMITTER FACILITY CODE NUMBER
STEP 4: PRESS
(FROM 1-15; 0 = IGNORE FACILITY CODE)
← EXITS PROGRAM MODE
STEP 5: PRESS
PROGRAM
NOTES:
1. REPEAT STEPS 2-4, IF REQUIRED, FOR EACH OF THE FOUR RECEIVER FACILITY
CODE LOCATIONS
2. WHEN THE TRANSMITTER FACILITY CODE IS SET TO "0", THE RECEIVER WILL
ACCEPT ALL TRANSMITTERS REGARDLESS OF THEIR FACILITY CODE
– 10 – REMOVING ALL TRANSMITTERS
← ENTERS PROGRAM MODE
STEP 1: PRESS PROGRAM FOR 3 SECONDS
← READY FOR PROGRAMMING
DISPLAY: THEN:
← TRANSMITTER REMOVING FUNCTION NUMBER
STEP 2: PRESS
← REMOVE COMMAND
STEP 3: PRESS
← VERIFY REMOVE COMMAND
STEP 4: PRESS
← MEMORY CLEAR
DISPLAY: THEN:
NOTES:
← EXITS
1. WARNING! ALL TRANSMITTERS INCLUDING
STEP 5: PRESS
PROGRAM
THE MGT TRANSMITTER WILL BE REMOVED
PROGRAM
MODE (TRANSMITTERS CANNOT BE INDIVIDUALLY
REMOVED)
2. WARNING! ALL OTHER OPTIONS WILL BE
RESET TO THE FACTORY DEFAULTS
– 3 – ADDING MDKP OR MDTK KEYPADS
← ENTERS PROGRAM MODE
STEP 1: PRESS FOR 3 SECONDS
PROGRAM
← READY FOR PROGRAMMING
DISPLAY: THEN:
← ADDING KEYPAD FUNCTION NUMBER
STEP 2: PRESS
← ENTER "1" TO ACTIVATE RELAY K1
STEP 3: PRESS OR
ENTER "2" TO ACTIVATE RELAY K2
← ONE TO FIVE DIGIT
STEP 4: PRESS
KEYPAD TRANSMITTER
ID CODE FOR THE PIN
← ENTER "1" FOR TIMED RELAY
STEP 5: PRESS OR
ENTER "0" TO TOGGLE RELAY
REPEAT STEPS 2-5 FOR ADDITIONAL KEYPADS OR KEYPAD PIN CODES
← EXITS PROGRAM MODE
STEP 6: PRESS
PROGRAM
NOTES:
TO DETERMINE THE TRANSMITTER ID CODE SENT BY A KEYPAD WHEN A
PARTICULAR PIN CODE IS ENTERED AT THE KEYPAD, OBSERVE THE AP-5 DISPLAY.
1. ENTER A PIN AND SEND A SIGNAL FROM THE KEYPAD
2. PRESS STAR ON THE AP-5 TO VIEW THE LAST THREE DIGITS OF THE ID CODE
3. PRESS DISPLAY ON THE AP-5 TO VIEW THE FIRST THREE DIGITS OF THE ID CODE
– 7 – MGT TRANSMITTER SUPERVISION
IF THE AP-5 BEEPS EVERY 5 SECONDS,
ONE OR MORE MGT OBSTACLE TRANSMITTER HAS SENT A SUPERVISORY SIGNAL
NOTE: WHEN ANY MGT HAS A SUPERVISORY CONDITION, TRANSMITTERS
WILL HAVE TO BE TRIGGERED TWICE TO GAIN ACCESS
← UTILITY FUNCTION #1 THEN 1-6 TO DISPLAY
PRESS
STATUS FOR MGT TRANSMITTERS
IN MEMORY LOCATIONS 1-6
← INDICATES MGT TRANSMITTER LOW BATTERY
← INDICATES AN MGT TAMPER OR LOOP FAULT
← INDICATES THAT HOURLY STATUS REPORTS HAVE
NOT BEEN RECEIVED FROM THE MGT TRANSMITTER IN
THE PREVIOUS FOUR HOURS
← AFTER CLEARING, DASHES INDICATE THAT NO
SUPERVISORY CONDITIONS EXIST WITH THE MGT
TRANSMITTER
← CLEARS MGT STATUS FROM AP-5 MEMORY AND STOPS BEEPER
PRESS
CANCEL NOTE: PRESS CANCEL WITHOUT PRESSING #1 TO CLEAR MGT
SUPERVISORY INDICATIONS FROM ALL MGT TRANSMITTERS
– 11 – REMOVING MGT TRANSMITTERS
← ENTERS PROGRAM MODE
STEP 1: PRESS PROGRAM FOR 3 SECONDS
← READY FOR PROGRAMMING
DISPLAY: THEN:
← MGT TRANSMITTER FUNCTION NUMBER
STEP 2: PRESS
← ENTER "1-6" FOR MGT MEMORY LOCATION NUMBER
STEP 4: PRESS
← REMOVE COMMAND
STEP 3: PRESS
← MGT REMOVED
DISPLAY: THEN:
← EXITS PROGRAM MODE
STEP 4: PRESS
PROGRAM
– 12 – SYSTEM TESTING
THE RADIO AND ACCESS GRANTED
ACTIVATE A TRANSMITTER THAT HAS BEEN
INDICATORS SHOULD LIGHT AND
PROGRAMMED (AND IS NOT SUSPENDED)
THE ACCESS DEVICE SHOULD OPERATE
IF MGT OBSTACLE TRANSMITTERS ARE
VERIFY THAT THAT ACCESS DEVICE
PROGRAMMED, RUN THE ACCESS DEVICE
STOPS OR REVERSES
AND TRIGGER EACH OBSTACLE SENSOR
THE ACCESS GRANTED INDICATOR
IF OPEN REQUEST PUSHBUTTONS ARE
SHOULD LIGHT AND THE ACCESS
INSTALLED, PRESS EACH ONE
DEVICE SHOULD OPERATE
– 4 – RELAY ACTIVATION TIME
← ENTERS PROGRAM MODE
STEP 1: PRESS FOR 3 SECONDS
PROGRAM
← READY FOR PROGRAMMING
DISPLAY: THEN:
← RELAY ACTIVATION TIME FUNCTION NUMBER
STEP 2: PRESS
← ENTER "1" FOR RELAY K1
STEP 3: PRESS OR
ENTER "2" FOR RELAY K2
← ENTER "01" TO "120" SECONDS
STEP 4: PRESS
FOR THE RELAY ACTIVATION TIME
(TWO DIGITS REQUIRED)
REPEAT STEPS 2-4 IF PROGRAMMING THE OTHER RELAY
← EXITS PROGRAM MODE
STEP 5: PRESS
PROGRAM
NOTES:
1. THE FACTORY DEFAULT ACTIVATION TIME FOR ACCESS RELAYS IS TWO
SECONDS
2. OBSTACLE RELAYS ALWAYS ACTIVATE FOR TWO SECONDS AND CANNOT
BE PROGRAMMED DIFFERENTLY
– 8 – SUSPENDING/ACTIVATING MGT TXS
TO DISABLE MGT SUPERVISION ON A SPECIFIC TRANSMITTER AND PREVENT
THE AP-5 FROM SOUNDING THE 5-SECOND MGT SUPERVISORY BEEPS
← ENTERS PROGRAM MODE
STEP 1: PRESS FOR 3 SECONDS
PROGRAM
← READY FOR PROGRAMMING
DISPLAY: THEN:
← MGT TRANSMITTER FUNCTION NUMBER
STEP 2: PRESS
← ENTER "1-6" FOR MGT MEMORY LOCATION NUMBER
STEP 3: PRESS
← SUSPEND/ACTIVATE COMMAND
STEP 4: PRESS
← MGT SUPERVISION CHANGED
DISPLAY: THEN:
(SUSPEND INDICATOR LIGHTS FOR
2 SECONDS WHEN MGT
HAS BEEN SUPSENDED)
← EXITS PROGRAM MODE
STEP 5: PRESS
PROGRAM
NOTES:
1. USE THE SAME COMMAND TO ACTIVATE (UNSUSPEND) THE MGT TRANSMITTER
2. SUSPENDING AN MGT WITH A SUPERVISORY CONDITION WILL ALLOW
TRANSMITTERS TO GAIN ACCESS WITH ONE ACTIVATION INSTEAD OF TWO
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twenty-four
(24) months. This warranty extends only to wholesale customers who buy direct from
Linear or through Linear's normal distribution channels. Linear does not warrant this product
to consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer's warranty, if any. There are no obligations or liabilities on the part of Linear LLC
for consequential damages arising out of or in connection with use or performance of
this product or other indirect damages with respect to loss of property, revenue, or profi t,
or cost of removal, installation, or reinstallation. All implied warranties, including implied
warranties for merchantability and implied warranties for fi tness, are valid only until the warranty
expires. This Linear LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT!!!
Linear radio controls provide a reliable communications link and fi ll an important need in portable
wireless signalling. However, there are some limitations which must be observed.
• The radios are required to comply with FCC Part 15 and Industry Canada Rules and
Regulations. As such, they have limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal at a time and may be
blocked by radio signals that occur on or near their operating frequencies, regardless of
code settings.
• Changes or modifi cations to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
• A general knowledge of radio and its vagaries should be gained prior to acting as a
wholesale distributor or dealer, and these facts should be communicated to the ultimate
users.
Copyright © 2007 Linear LLC 227701 A