Fiat 500e 2018 Owner's Manual

page of 302

/ 302
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

FIAT

500e

2 0 1 8

O W N E R ' S M A N U A L

Table of Contents

Chapters

Table of Contents

Need help?

Do you have a question about the 500e 2018 and is the answer not in the manual?

Questions and answers

Ewa Boer

April 15, 2025

Hello, Where in this car is located a manual emeregency release cable for EV cables?

Summary of Contents for Fiat 500e 2018

Page 1 FIAT 500e ® 2 0 1 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5 INTRODUCTION CONTENTS INTRODUCTION......4 WARNINGS AND CAUTIONS ....5 HOW TO USE THIS MANUAL .
Page 6: Introduction 3
When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techni- Congratulations on selecting your new FIAT 500e. Be cians and genuine MOPAR® parts, and cares about your assured that your 500e represents an elegant marriage of satisfaction.
Page 7: Introduction
INTRODUCTION 5 WARNINGS AND CAUTIONS VEHICLE MODIFICATIONS/ALTERATIONS This Owner’s Manual contains WARNINGS against oper- WARNING! ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against Any modifications or alterations to this vehicle could procedures that could result in damage to your vehicle.
Page 9 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......8 INSTRUMENT PANEL .....10 REAR VIEW .
Page 10: Front View
8 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Exterior Mirrors 3 — Underhood Compartment 2 — Windshield 4 — Headlights...
Page 11: Rear View
GRAPHICAL TABLE OF CONTENTS 9 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 12: Instrument Panel
10 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Multifunction Lever 5 — Windshield Wiper Lever 3 — Steering Wheel 6 — Radio...
Page 13: Interior
GRAPHICAL TABLE OF CONTENTS 11 INTERIOR Interior 1 — Door Handles 4 — Climate Controls 2 — Seats 5 — Gear Selector 3 — Switch Panel...
Page 15: Table Of Contents
GETTING TO KNOW YOUR VEHICLE CONTENTS ▫ Charge Times ......36 HIGH VOLTAGE BATTERY ....16 500e ELECTRIC VEHICLE FEATURES .
Page 16 14 GETTING TO KNOW YOUR VEHICLE ▫ Central Lock/Unlock (Switch Safe Lock ▫ Power Mirrors ......55 Device) —...
Page 17 GETTING TO KNOW YOUR VEHICLE 15 ▫ Interior Light Timing (On/Right Position) ..59 ▫ To Open ......74 ▫...
Page 18: High Voltage Battery
16 GETTING TO KNOW YOUR VEHICLE HIGH VOLTAGE BATTERY Your vehicle is equipped with a Lithium-ion high voltage battery that is used to power the electric powertrain systems and the 12 volt vehicle electrical system. The high voltage battery is located under the vehicle. The high voltage battery is maintenance free and designed to last for the life of the vehicle.
Page 19 GETTING TO KNOW YOUR VEHICLE 17 • Lithium-ion batteries can be recharged and discharged General Information thousands of times. The vehicle is also equipped with a Battery Management High Voltage Battery Service Disconnect System that is designed to: • Ensure safe operation The high voltage battery service disconnect is located under the rear passenger seat lower cushion.
Page 20: 500E Electric Vehicle Features
18 GETTING TO KNOW YOUR VEHICLE 500e ELECTRIC VEHICLE FEATURES (35.5 km/h). At approximately 22 mph (35.5 km/h), the warning system is deactivated and will automatically be Understanding the unique characteristics of your 500e will active when the vehicle returns to approximately 20 mph help ensure maximum performance and the best driving (32 km/h).
Page 21: Climate Control (Hvac System)
GETTING TO KNOW YOUR VEHICLE 19 E-Park is activated when the driver pushes the PARK Electric Air Conditioning Compressor button. An electric motor activates the parking pawl and Your 500e uses an electric air conditioning compressor. The locks the single-speed transmission when the vehicle is air conditioning compressor is powered by the high volt- placed into PARK.
Page 22: Smartphone Features (Not Available In Canada)
20 GETTING TO KNOW YOUR VEHICLE Smartphone Features (Not Available In Canada) How do I get the Uconnect smartphone App? With the Uconnect app, you can monitor the state of charge Download the Uconnect app from the following websites: of the high voltage battery or initiate charging from your https://itunes.apple.com (Apple users) or https:// phone.
Page 23: High Voltage Charging Operation
GETTING TO KNOW YOUR VEHICLE 21 Once in the registration website, you will need to enter 4. From the 500e owner’s site you will be able to download your vehicle’s VIN and Connectivity ID. The connectivity the 500e Uconnect mobile application and learn how to ID is found in the vehicle’s instrument cluster.
Page 24: Ac Level 1 Charging (120V, 15 Amp)
22 GETTING TO KNOW YOUR VEHICLE SAE J1772 Charge Receptacle Charging Cord Set NOTE: The charge inlet door locks and unlocks with the WARNING! vehicle doors. Shock, fire, property damage, or personal injury may AC Level 1 Charging (120V, 15 Amp) occur if the Portable EVSE Cordset is not used prop- Your vehicle is equipped with a 120 Volt AC, SAE J1772 erly.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 WARNING! (Continued) • Do not use this product if the enclosure or the Charge Connector is broken, cracked, open, or shows any other indication of damage. • Do not use Portable EVSE Cordset with an extension cord.
Page 26 24 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Ensure that the EVSEs are always stored in a safe place. Do not expose them to rain or wet conditions. Avoid pouring or dipping water or other liquids over them. If water penetrates the electrical device, the risk or electrical shock increases.
Page 27 GETTING TO KNOW YOUR VEHICLE 25 where the indicator light will flash, a green AC indicator light and two green charge rate indicator lights indicate that the cordset is ready for use. AC Plug And Wall Receptacle WARNING! Improper connection of the equipment-grounding con- Cordset Indicator Lights ductor could result in a risk of electric shock.
Page 28 26 GETTING TO KNOW YOUR VEHICLE Status Indicator Display” in this section for further information on the charging cordset status. • Wall Receptacle – Check whether the wall receptacle is functional (no power outage) and/or plug the charg- ing cordset into a different wall receptacle. •...
Page 29 GETTING TO KNOW YOUR VEHICLE 27 The AC Power Indicator displays the status and safety of the input power. If this indicator is green, the power is within acceptable limits to charge the vehicle. If only the AC Power Indicator is flashing red, then there is a problem with the AC power at the electrical outlet.
Page 30 28 GETTING TO KNOW YOUR VEHICLE The fault code list in the table below provides a reference faults is provided by a fault code that is displayed on the for the important faults that are detected by the Portable two green Charge Rate Indicators. The fault code consists EVSE Cordset.
Page 31 GETTING TO KNOW YOUR VEHICLE 29 Portable EVSE Cordset Fault Code List Flashing Flashing Fault Fault Indication Recommended Actions Indicator Code 1, 2, 1, 1 AC Power Incorrect Electrical Sup- Attempt to charge the vehicle at a different outlet. Contact a certified electrician to check the electrical outlet and AC Supply (house wiring).
Page 32 30 GETTING TO KNOW YOUR VEHICLE Portable EVSE Cordset Fault Code List Flashing Flashing Fault Fault Indication Recommended Actions Indicator Code 1, 2, 1, 2 Fault CCID Leakage Current Disconnect charge connector and retry charging. If problem per- Detected sists, check the Portable EVSE Cordset and Vehicle at a service location.
Page 33 GETTING TO KNOW YOUR VEHICLE 31 Portable EVSE Cordset Fault Code List Flashing Flashing Fault Fault Indication Recommended Actions Indicator Code 1, 1, 1, 2 Fault & AC Hot AC Power Plug Use caution as the Portable EVSE Cordset AC Power Plug may Power Warning be hot.
Page 34 32 GETTING TO KNOW YOUR VEHICLE • Do not use the charging cordset if it is visibly damaged. FCC Notice: Contact an authorized dealer for service. This unit has systems that operate on a radio frequency • Do not place fingers, or any other objects inside the that comply with Part 15 of the Federal Communications charge connector.
Page 35 GETTING TO KNOW YOUR VEHICLE 33 Vehicle Charge Indicators Charge Low And Limited Power Messages Instrument Cluster High Voltage Battery Gauge The state of charge is monitored during normal operation. If the state of charge reaches certain thresholds the follow- There is a battery gauge indicator located on the instru- ing messages display on the cluster: ment cluster.
Page 36 34 GETTING TO KNOW YOUR VEHICLE • charge low limited power mode — turtle flashes at 0% Instrument Panel State Of Charge Indicator until condition changes. In addition to the battery gauge your vehicle is equipped NOTE: The limited power mode can also be activated if the with a visual state of charge indicator.
Page 37: Ac Level 2 Charging (240V, 30 Amp)
GETTING TO KNOW YOUR VEHICLE 35 NOTE: In the event of an error in the charging process the NOTE: The vehicle should start charging automatically. If outer two lights will blink. not, please check the following: • Charging Station – Check the indications and instruc- Number Of Indicator Percent Of Battery Charge tions at the charging station.
Page 38: Charge Times
36 GETTING TO KNOW YOUR VEHICLE Charge Times KEYS The following factors determine the time it takes to charge Key With Remote Control the high voltage battery: The Remote Keyless Entry (RKE) key fob contains an • The high voltage battery’s current state of charge integrated key.
Page 39 GETTING TO KNOW YOUR VEHICLE 37 NOTE: Replacing The Battery In The Key With Remote • The authorized dealer that sold you your vehicle has the Control key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your autho- rized dealer.
Page 40: Ignition Switch
38 GETTING TO KNOW YOUR VEHICLE To replace the battery, proceed as follows: General Information The following regulatory statement applies to all radio 1. Push mechanical release button to open the mechanical frequency (RF) devices equipped in this vehicle: key. This device complies with Part 15 of the FCC Rules and 2.
Page 41 GETTING TO KNOW YOUR VEHICLE 39 NOTE: The transmission must be placed in PARK before the key is turned to the STOP position. Then, the key can be removed. • AVV: vehicle start-up. • MAR: driving position. All electrical devices are en- abled.
Page 42: Key-In-Ignition Reminder
40 GETTING TO KNOW YOUR VEHICLE Key-In-Ignition Reminder WARNING! (Continued) Opening the driver’s door when the key is in the ignition • Never leave children alone in a vehicle, or with and the ignition switch position is in the OFF/LOCK access to an unlocked vehicle.
Page 43: Key Programming
GETTING TO KNOW YOUR VEHICLE 41 General Information CAUTION! The following regulatory statement applies to all radio • Always remove the Sentry Key from the vehicle and frequency (RF) devices equipped in this vehicle: lock all doors when leaving the vehicle unattended. This device complies with Part 15 of the FCC Rules and •...
Page 44: To Arm The System
42 GETTING TO KNOW YOUR VEHICLE visible signals: the horn will pulse, the park lamps and/or If the horn sounds a second time, check that all doors, hood turn signals will flash, and the vehicle security light on the and liftgate are closed correctly, then rearm the system. instrument panel will flash.
Page 45: Central Lock/Unlock (Switch Safe Lock Device) - If Equipped
GETTING TO KNOW YOUR VEHICLE 43 Central Lock/Unlock (Switch Safe Lock Device) — Activating The Safe Lock Device If Equipped The Safe Lock device is enabled on all the doors by quickly This safety device prevents the operation of the interior double-pushing the lock button on the key fob.
Page 46: Doors
44 GETTING TO KNOW YOUR VEHICLE DOORS NOTE: The manual lock knob unlocks each individual door separately. Manual Lock To lock each door from the inside, push the inside door WARNING! handle toward the door until the red lock indicator is •...
Page 47: Power Door Locks
GETTING TO KNOW YOUR VEHICLE 45 CAUTION! An unlocked car is an invitation. Always remove the key from the ignition and lock all doors when leaving the vehicle unattended. Power Door Locks A power door lock switch is incorporated into the driver door handle.
Page 48: Seats
46 GETTING TO KNOW YOUR VEHICLE SEATS Manual Adjustment Front Seats Seats are a part of the Occupant Restraint System of the Forward/Rearward Adjustment vehicle. The adjusting bar is located at the front of the seats, near the floor. WARNING! •...
Page 49 GETTING TO KNOW YOUR VEHICLE 47 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 50 48 GETTING TO KNOW YOUR VEHICLE EZ Entry Feature The driver and front passenger seats have an EZ entry feature for rear seat passengers. Pull forward on the release lever, located on the outboard side of the seatback, dump the seatback forward, then slide the seat forward to allow access in and out of the rear seat.
Page 51: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 49 Memory Seat Feature seatbacks. The controls for the front heated seats are located on the center instrument panel area. Both front seats have a memory feature, which can operate in two ways: Push the switch once to turn on the heated seats. Push the switch a second time to shut the heating •...
Page 52: Manual Folding Rear Seat
50 GETTING TO KNOW YOUR VEHICLE Manual Folding Rear Seat The rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded-down position to provide a flat load floor cargo area.
Page 53: Reactive Head Restraints - Front Seats
GETTING TO KNOW YOUR VEHICLE 51 WARNING! • All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash.
Page 54: Rear Head Restraints
52 GETTING TO KNOW YOUR VEHICLE NOTE: To remove the head restraint, raise it as far as it can WARNING! go then push the release button and the adjustment button • A loose head restraint thrown forward in a collision at the base of each post while pulling the head restraint up.
Page 55: Steering Wheel
GETTING TO KNOW YOUR VEHICLE 53 WARNING! ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat. STEERING WHEEL Tilt Steering Column — If Equipped This feature allows you to tilt the steering column upward or downward.
Page 56: Mirrors
54 GETTING TO KNOW YOUR VEHICLE MIRRORS Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from Inside Day/Night Mirror vehicles behind you. You can turn the feature on or off by The mirror can be adjusted up, down, left, and right for pushing the button at the base of the mirror.
Page 57: Power Mirrors
GETTING TO KNOW YOUR VEHICLE 55 The power mirror controls consist of a mirror select switch CAUTION! and a four-way mirror control switch. To adjust a mirror, push the mirror select switch to either the L (left) or R To avoid damage to the mirror during cleaning, never (right) to select the mirror you need to adjust.
Page 58: Spotter Mirror - If Equipped
56 GETTING TO KNOW YOUR VEHICLE Spotter Mirror — If Equipped EXTERIOR LIGHTS Some models are equipped with a driver’s side spotter Multifunction Lever mirror. The spotter mirror allows for a greater range of The multifunction lever, located on the left side of the visibility on the driver’s side of the vehicle.
Page 59: Daytime Running Lights
GETTING TO KNOW YOUR VEHICLE 57 NOTE: When the headlights are turned on, the Daytime Parking Lights Running Lights will be deactivated. To turn on the parking lights, remove the key or Daytime Running Lights turn the ignition to OFF/LOCK position and To activate the Daytime Running Lights (DRL), rotate the turn on the headlights.
Page 60: Turn Signals
58 GETTING TO KNOW YOUR VEHICLE Fog Light Switch Turn Signal Operation Push the switch once to turn the front fog lights on. Push NOTE: The indicators will automatically turn off when the the switch a second time to turn the front fog lights off. turn has been completed and the steering wheel is returned to a straight position.
Page 61: Interior Lights
GETTING TO KNOW YOUR VEHICLE 59 INTERIOR LIGHTS Interior Light Timing (Center Position) The interior light switches are located in the overhead There are four different modes of operation that can be console. The interior lights can be set to three different activated in this position: positions (Off/Left Position, Center Position, On/Right •...
Page 62: Dimmer Control
60 GETTING TO KNOW YOUR VEHICLE Dimmer Control The brightness of the instrument panel lighting can be regulated by pushing the buttons on the right side of the instrument cluster. The (+) button increases the brightness and the (-) button decreases the brightness. You can control brightness of the radio by itself or the entire instrument panel.
Page 63: Front Windshield Wiper Operation
GETTING TO KNOW YOUR VEHICLE 61 Front Windshield Wiper Operation Low Speed There are four different modes of operation for the front Push the lever downward to the second detent. The wipers windshield wipers. The windshield wiper lever can be will operate at low speed.
Page 64: Rear Windshield Wiper
62 GETTING TO KNOW YOUR VEHICLE Front Windshield Washer Operation Manual High Speed/Mist Pull the windshield wiper/washer lever toward the steer- Push the lever upward from the off position. The wipers ing wheel to activate the washers. The wipers will activate will operate at high speed to clear off road mist or spray automatically for three cycles after the lever is released.
Page 65: Climate Controls
GETTING TO KNOW YOUR VEHICLE 63 Rear Windshield Washer Operation Push the windshield wiper/washer lever toward the in- strument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released.
Page 66: Automatic Temperature Control Overview
64 GETTING TO KNOW YOUR VEHICLE Automatic Temperature Control Overview Automatic Temperature Controls...
Page 67 GETTING TO KNOW YOUR VEHICLE 65 Control Descriptions Icon Description A/C Button Push and release to change the current setting, the indicator illuminates when A/C is ON. Per- forming this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off.
Page 68 66 GETTING TO KNOW YOUR VEHICLE Icon Description Front Defrost Button Push and release to change the current airflow setting to Defrost mode. The indicator illumi- nates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase.
Page 69 GETTING TO KNOW YOUR VEHICLE 67 Icon Description Modes Control: Push the button in the center of the knob to change the airflow distribution mode. The airflow distri- bution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.
Page 70 68 GETTING TO KNOW YOUR VEHICLE Icon Description Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
Page 71: Automatic Temperature Control (Atc) - If Equipped
GETTING TO KNOW YOUR VEHICLE 69 Climate Control Functions Recirculation In cold weather, use of Recirculation mode may lead to A/C (Air Conditioning) excessive window fogging. The Recirculation feature may The Air Conditioning (A/C) button allows the operator to be unavailable if conditions exist that could create fogging manually activate or deactivate the air conditioning sys- on the inside of the windshield.
Page 72: Operating Tips
70 GETTING TO KNOW YOUR VEHICLE NOTE: Operating Tips • It is not necessary to move the temperature settings for NOTE: Refer to the chart at the end of this section for cold or hot vehicles. The system automatically adjusts suggested control settings for various weather conditions.
Page 73 GETTING TO KNOW YOUR VEHICLE 71 NOTE: If the vehicle is parked and off charge for longer Outside Air Intake than two months, the 12V battery should be disconnected. Make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves.
Page 74: Windows
72 GETTING TO KNOW YOUR VEHICLE Operating Tips Chart WINDOWS Power Window Controls The power window controls are located on the shifter bezel, below the climate controls, which operate the driver and passenger door windows. The window controls will operate when the ignition switch is in the MAR (ACC/ ON/RUN) position.
Page 75: Auto-Down
GETTING TO KNOW YOUR VEHICLE 73 partially open positions. This is a normal occurrence and WARNING! can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together Never leave children unattended in a vehicle, and do to minimize the buffeting.
Page 76: To Open
74 GETTING TO KNOW YOUR VEHICLE open fully, then stop automatically. This is called “Express WARNING! Open”. During Express Open operation, any movement of • Never leave children alone in a vehicle, or with the sunroof switch will stop the sunroof. access to an unlocked vehicle.
Page 77: Sun Shade - If Equipped
GETTING TO KNOW YOUR VEHICLE 75 Sun Shade — If Equipped Pinch Protect Feature For vehicles equipped with either a power sunroof or a This feature will detect an obstruction in the opening of the fixed glass roof, there is a sun shade that can be open or sunroof during Express Close operation.
Page 78: Hood
76 GETTING TO KNOW YOUR VEHICLE HOOD 2. Slide the safety catch under the front edge of the hood, near the center, to the right. Then raise the hood. Opening To open the hood, two latches must be released. 1. Pull the bottom of the RED hood release lever, located on the left kick panel, rearward.
Page 79: Closing
GETTING TO KNOW YOUR VEHICLE 77 3. Lift the hood prop rod that clips to the right side (left Closing side when standing in front of the hood) of the under- hood compartment. Place the hood prop rod in the hole WARNING! of hood hinge to secure the hood in the open position.
Page 80: Liftgate
78 GETTING TO KNOW YOUR VEHICLE LIFTGATE INTERNAL EQUIPMENT Opening Storage To unlock the liftgate, use the key fob or activate the power Glove Compartment door lock switches located on the driver door handle. The glove compartment is located on the passenger side of To open the liftgate, squeeze the liftgate release handle and the instrument panel.
Page 81: Cupholders
GETTING TO KNOW YOUR VEHICLE 79 Cupholders Rear Cupholders For rear passengers, there are cupholders located on the Front Cupholders floor between the front driver and passenger seats. For the driver and front passenger, cupholders are located on the floor console between the front seats. Rear Cupholders Front Cupholders...
Page 82: Sun Visors
80 GETTING TO KNOW YOUR VEHICLE Sun Visors Electrical Power Outlets The driver and passenger sun visors are located on the There is a standard 12 Volt (13 Amp) power outlet, located headliner, near the front windshield. The sun visors can be in the floor console, for added convenience.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watts (13 Amps) power rating is exceeded, the fuse protecting the system will need to be replaced. •...
Page 84 82 GETTING TO KNOW YOUR VEHICLE WARNING! CAUTION! (Continued) enough, the vehicle’s battery will discharge suffi- To avoid serious injury or death: ciently to degrade battery life and/or prevent the • Only devices designed for use in this type of outlet vehicle from moving.
Page 85 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS ▫ Red Warning Lights ..... .90 INSTRUMENT CLUSTER ....84 ▫...
Page 86: Instrument Cluster
84 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster...
Page 87: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 85 Instrument Cluster Descriptions INSTRUMENT CLUSTER DISPLAY Your vehicle may be equipped with an instrument cluster 1. Battery Charge Gauge display, which offers useful information to the driver. With • This gauge indicates the charge level of the battery. the ignition in the STOP/OFF position, opening/closing of 2.
Page 88 86 GETTING TO KNOW YOUR INSTRUMENT PANEL Instrument Cluster Display Control Buttons The instrument cluster display control buttons are located on the right side of the instrument cluster. There are three control buttons that are used to navigate through the instrument cluster display functions: •...
Page 89: Display Menu Set-Up
GETTING TO KNOW YOUR INSTRUMENT PANEL 87 Push and release the MENU button briefly to access the and Climate Controls). Refer to “Uconnect Settings” in instrument cluster display. Push and hold the MENU “Multimedia” for further information. button (approximately one second) to return to the main Display Menu Set-Up screen.
Page 90: Trip Computer
88 GETTING TO KNOW YOUR INSTRUMENT PANEL Selecting An Option Of The Main Menu Without Sub- 4. Push and release the up arrow and down arrow (by menu: single pushes) to select the new setting for this submenu option. 1. Briefly push and release the MENU button to select the main menu option to set.
Page 91: Trip Functions
GETTING TO KNOW YOUR INSTRUMENT PANEL 89 New Trip To reset: • Push and hold the TRIP button manually. • When the “Trip Distance” reaches 9999.9 miles/kilometers or when the “Elapsed Time” reaches 29.59 (29 hours and 59 minutes) the system will reset automatically. •...
Page 92: Values Displayed
90 GETTING TO KNOW YOUR INSTRUMENT PANEL Values Displayed WARNING LIGHTS AND MESSAGES Range The warning/indicator lights will illuminate in the instru- ment panel together with a dedicated message and/or This indicates the distance which may be travelled with the acoustic signal when applicable.
Page 93 GETTING TO KNOW YOUR INSTRUMENT PANEL 91 — Brake Warning Light NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. This warning light monitors various brake functions, in- The vehicle should have service performed, and the brake cluding brake fluid level and parking brake application.
Page 94 92 GETTING TO KNOW YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN position. Continued operation with reduced assist could pose a NOTE: This light shows only that the parking brake is safety risk to yourself and others.
Page 95: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 93 driver’s seat belt is unbuckled, a chime will sound and the the conventional brake system will continue to operate light will turn on. When driving, if the driver or front normally, assuming the Brake Warning Light is not also on. passenger seat belt remains unbuckled, the Seat Belt Re- If the ABS light does not turn on when the ignition is minder Light will flash or remain on continuously and a...
Page 96 94 GETTING TO KNOW YOUR INSTRUMENT PANEL • The “ESC Off Indicator Light” and the “ESC Indicator • Parking Lights Light” come on momentarily each time the ignition is • Daytime Running Lights placed in the ON/RUN or ACC/ON/RUN position. •...
Page 97 GETTING TO KNOW YOUR INSTRUMENT PANEL 95 can lead to tire failure. Under-inflation also reduces fuel CAUTION! efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Do not continue driving with one or more flat tires as handling may be compromised.
Page 98: Yellow Indicator Lights
96 GETTING TO KNOW YOUR INSTRUMENT PANEL erative Brake System (RBS) and the need for system CAUTION! service. See an authorized dealer as soon as possible. The TPMS has been optimized for the original equip- Refer to “Regenerative Braking” in “Safety” for further ment tires and wheels.
Page 99: Green Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 97 — Front Fog Indicator Light — If Equipped CAUTION! This indicator light will illuminate when the front fog Failure to follow these cautions can cause damage to lights are on. the heating elements: •...
Page 100: White Indicator Lights
98 GETTING TO KNOW YOUR INSTRUMENT PANEL White Indicator Lights WARNING! — Cruise Control ON Indicator Light • ONLY an authorized service technician should connect This indicator light will illuminate when the electronic equipment to the OBD II connection port in order to speed control is ON, but a speed has not been set.
Page 101 SAFETY CONTENTS ▫ Supplemental Restraint Systems (SRS) ..120 SAFETY FEATURES ..... .100 ▫ Four-Wheel Anti-Lock Brake System (ABS) ..100 ▫...
Page 102: Safety Features
100 SAFETY SAFETY FEATURES WARNING! (Continued) Four-Wheel Anti-Lock Brake System (ABS) by improperly installed or high output radio trans- mitting equipment. This interference can cause pos- The Four-Wheel ABS is designed to aid the driver in sible loss of anti-lock braking capability. Installation maintaining vehicle control under adverse braking condi- of such equipment should be performed by qualified tions.
Page 103: Electronic Brake Control System
SAFETY 101 When you are in a severe braking condition involving the results in the best BAS assistance. To receive the benefit of use of the ABS, you will experience some pedal drop as the the system, you must apply continuous braking pressure vehicle comes to a stop.
Page 104 102 SAFETY • Understeer - when the vehicle is turning less than (BLD), functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel appropriate for the steering wheel position. on a driven axle is spinning faster than the other, the NOTE: The ESC Off switch is located on the instrument system will apply the brake of the spinning wheel.
Page 105 SAFETY 103 deep snow, sand or gravel conditions and more wheel spin WARNING! (Continued) than ESC would normally allow is required to gain trac- the performance of the ESC system. Changes to the tion. steering system, suspension, braking system, tire To turn ESC on again, momentarily pushing the switch type and size or wheel size may adversely affect ESC again.
Page 106 104 SAFETY ESC Activation/Malfunction Indicator Light And NOTE: ESC OFF Indicator Light • The ESC Activation/Malfunction Indicator Light and the ESC OFF Indicator Light come on momentarily each time the ignition switch is turned ON. The ESC Activation/Malfunction Indicator Light in the instrument cluster will come on when the •...
Page 107: Auxiliary Driving Systems
SAFETY 105 The RBS uses conventional hydraulic friction brakes, re- Maintenance” for information on how to properly inflate generative braking, or a combination to slow the vehicle. If the vehicle’s tires. The tire pressure will also increase as the the system detects slippery conditions while braking, vehicle is driven.
Page 108 106 SAFETY and the measured tire pressure is 28 psi (193 kPa), a CAUTION! (Continued) temperature drop to 20°F (-7°C) will decrease the tire Customers are encouraged to use OEM wheels to pressure to approximately 24 psi (165 kPa). This tire assure proper TPM feature operation.
Page 109 SAFETY 107 • Under-inflation also reduces the high voltage battery The TPMS consists of the following components: range and tire tread life, and may affect the vehicle’s • Receiver module handling and stopping ability. • Four Tire Pressure Monitoring Sensors •...
Page 110 108 SAFETY TPMS Warning When a system fault is detected, the Tire Pressure Moni- toring System Warning Light will flash on and off for 75 seconds and then remain on solid. The system fault will sound a chime and also display a “Service Tire Pressure Monitoring System”...
Page 111 SAFETY 109 • After driving the vehicle for up to 20 minutes above A system fault can occur due to any of the following: 15 mph (24 km/h), the Tire Pressure Monitoring System 1. Signal interference due to electronic devices or driving Warning Light will flash on and off for 75 seconds and next to facilities emitting the same radio frequencies as then remain on solid.
Page 112: Occupant Restraint Systems
110 SAFETY General Information Important Safety Precautions This device complies with Part 15 of the FCC rules and RSS Please pay close attention to the information in this section. 210 of Industry Canada. Operation is subject to the follow- It tells you how to use your restraint system properly, to ing conditions: keep you and your passengers as safe as possible.
Page 113: Seat Belt Systems
SAFETY 111 5. You should read the instructions provided with your WARNING! (Continued) child restraint to make sure that you are using it younger, including a child in a rear-facing child properly. restraint. 6. All occupants should always wear their lap and shoul- •...
Page 114 112 SAFETY seat belts. The Belt Alert feature is active whenever the until the seat belts are buckled. The BeltAlert warning ignition switch is in the START or ON/RUN position. sequence may repeat based on vehicle speed until the driver and occupied outboard front seat passenger seat Initial Indication belts are buckled.
Page 115 SAFETY 113 NOTE: If BeltAlert has been deactivated and the driver or WARNING! (Continued) outboard front seat passenger (if equipped with outboard • In a collision, you and your passengers can suffer front passenger seat BeltAlert) is unbuckled the Seat Belt much greater injuries if you are not properly buckled Reminder Light will turn on and remain on until the driver up.
Page 116 114 SAFETY WARNING! (Continued) WARNING! (Continued) seat belt. Follow these instructions to wear your seat too high on your body, possibly causing internal belt safely and to keep your passengers safe, too. injuries. Always buckle your seat belt into the •...
Page 117 SAFETY 115 WARNING! (Continued) loose parts. Damaged parts must be replaced imme- diately. Do not disassemble or modify the seat belt system. Seat belt assemblies must be replaced after a collision. Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat.
Page 118 116 SAFETY Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low across 5. Position the shoulder belt across the shoulder and chest your hips, below your abdomen. To remove slack in the with minimal, if any slack so that it is comfortable and lap belt portion, pull up on the shoulder belt.
Page 119 SAFETY 117 Lap/Shoulder Belt Untwisting Procedure position, an authorized dealer can provide you with a Seat Belt Extender. The Seat Belt Extender should be used only Use the following procedure to untwist a twisted lap/ if the existing seat belt is not long enough. When the Seat shoulder belt.
Page 120 118 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 121 SAFETY 119 Switchable Automatic Locking Retractor (ALR) webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR. If the The seat belts in the passenger seating positions are ALR is activated, you will hear a clicking sound as the seat equipped with a Switchable Automatic Locking Retractor belt retracts.
Page 122: Supplemental Restraint Systems (Srs)
120 SAFETY How To Engage The Automatic Locking Mode WARNING! (Continued) 1. Buckle the combination lap and shoulder belt. • Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children 2. Grasp the shoulder portion and pull downward until who are using booster seats.
Page 123 SAFETY 121 • Instrument Panel The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds • Knee Impact Bolsters for a self-check when the ignition switch is in the MAR/ • Driver and Front Passenger Air Bags ACC/ON/RUN position.
Page 124 122 SAFETY NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. In this condition the air bags may not be ready to inflate for your protection. Have an authorized dealer service the air bag system immediately.
Page 125 SAFETY 123 driver or front passenger seat belt is buckled. The seat belt WARNING! (Continued) buckle switch may adjust the inflation rate of the Ad- • Never place a rear-facing child restraint in front of an vanced Front Air Bags. air bag.
Page 126 124 SAFETY When the ORC detects a collision requiring the front air WARNING! (Continued) bags, it signals the inflator units. A large quantity of collisions, air bags won’t deploy at all. Always wear non-toxic gas is generated to inflate the front air bags. your seat belts even though you have air bags.
Page 127 SAFETY 125 Supplemental Driver Knee Air Bag This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column. The Supplemental Driver Knee Air Bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and front air bags.
Page 128 126 SAFETY WARNING! Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. Supplemental Side Air Bag Inflatable Curtains (SABICs) This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABICs).
Page 129 SAFETY 127 The SABICs may help reduce the risk of partial or complete ORC in determining the appropriate response to impact ejection of vehicle occupants through side windows in events. The system is calibrated to deploy the Side Air Bags certain side impact events.
Page 130 128 SAFETY WARNING! (Continued) WARNING! (Continued) • Relying on the Side Air Bags alone could lead to or killed. Occupants, including children, should never lean on or sleep against the door, side win- more severe injuries in a collision. The Side Air Bags dows, or area where the side air bags inflate, even if work with your seat belt to restrain you properly.
Page 131 SAFETY 129 • Seat Belt Pretensioners event, and deployment of the Side Air Bags is appropriate, the rollover sensing system will also deploy the seat belt • Seat Track Position Sensors pretensioners on both sides of the vehicle. If A Deployment Occurs The SABICs may help reduce the risk of partial or complete The front air bags are designed to deflate immediately after ejection of vehicle occupants through side windows in...
Page 132 130 SAFETY inflation. These airborne particles may irritate the skin, Enhanced Accident Response System eyes, nose, or throat. If you have skin or eye irritation, In the event of an impact, if the communication network rinse the area with cool water. For nose or throat remains intact, and the power remains intact, depending irritation, move to fresh air.
Page 133 SAFETY 131 • Electric power steering state and must be towed to an authorized dealer immedi- • Brake booster ately to be inspected and have the Enhanced Accident Response System reset. • Electric park brake • Automatic transmission gear selector Maintaining Your Air Bag System •...
Page 134 132 SAFETY • How far (if at all) the driver was depressing the accel- WARNING! (Continued) erator and/or brake pedal; and, cover and cushion, needs to be serviced in any way • How fast the vehicle was traveling. (including removal or loosening/tightening of seat attachment bolts), take the vehicle to an authorized These data can help provide a better understanding of the dealer.
Page 135: Child Restraints
SAFETY 133 Child Restraints There are different sizes and types of restraints for children from newborn size to the child almost large enough for an Everyone in your vehicle needs to be buckled up at all adult safety belt. Always check the child seat Owner’s times, including babies and children.
Page 136 134 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Of Child Child Size, Height, Weight Or Age Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convert- younger and who have not reached ible Child Restraint, facing rearward the height or weight limits of their in the rear seat of the vehicle...
Page 137 SAFETY 135 Infant And Child Restraints WARNING! (Continued) Safety experts recommend that children ride rear-facing in younger, including a child in a rear-facing child the vehicle until they are two years old or until they reach restraint. either the height or weight limit of their rear-facing child •...
Page 138 136 SAFETY Children Too Large For Booster Seats WARNING! Children who are large enough to wear the shoulder belt • Improper installation can lead to failure of an infant comfortably, and whose legs are long enough to bend over or child restraint. It could come loose in a collision. the front of the seat when their back is against the seatback, The child could be badly injured or killed.
Page 139 SAFETY 137 A child’s squirming or slouching can move the belt out of WARNING! position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a Never allow a child to put the shoulder belt under an booster seat to position the seat belt on the child correctly.
Page 140 138 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 141 SAFETY 139 Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until the weight of the child restraint) for using the combined weight of the child and the child re- LATCH anchorage system to attach the child straint is 65 lbs (29.5 kg).
Page 142 140 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint touch the The child seat may touch the back of the front back of the front passenger seat? passenger seat if the child restraint manufac- turer also allows contact.
Page 143 SAFETY 141 Locating The Upper Tether Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower There are tether strap anchorages behind each anchorage and a way to tighten the connection to the rear seating position located on the back of the anchorage.
Page 144 142 SAFETY To Install A LATCH-Compatible Child Restraint 3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seating If the selected seating position has a Switchable Automatic position. Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below.
Page 145 SAFETY 143 How To Stow An Unused Switchable-ALR (ALR) WARNING! (Continued) Seat Belt: • Child restraint anchorages are designed to withstand When using the LATCH attaching system to install a child only those loads imposed by correctly-fitted child restraint, stow all ALR seat belts that are not being used by restraints.
Page 146 144 SAFETY The seat belts in the passenger seating positions are Lap/Shoulder Belt Systems For Installing Child equipped with a Switchable Automatic Locking Retractor Restraints In This Vehicle (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
Page 147 SAFETY 145 Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to the with the seat belt to attach a forward...
Page 148 146 SAFETY Installing A Child Restraint With A Switchable 2. Pull enough of the seat belt webbing from the retractor Automatic Locking Retractor (ALR): to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path. Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a 3.
Page 149 SAFETY 147 8. If the child restraint has a top tether strap and the WARNING! (Continued) seating position has a top tether anchorage, connect the “Lower Anchors and Tethers for CHildren (LATCH) tether strap to the anchorage and tighten the tether Restraint System”...
Page 150: Transporting Pets
148 SAFETY two posts. If not possible, lower the head restraint and WARNING! pass the tether strap around the outboard side of the • An incorrectly anchored tether strap could lead to head restraint. increased head motion and possible injury to the 3.
Page 151: Safety Tips
SAFETY 149 SAFETY TIPS Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision Transporting Passengers if they have been damaged (i.e., bent retractor, torn web- NEVER TRANSPORT PASSENGERS IN THE CARGO bing, etc.).
Page 152 150 SAFETY feel the air directed against the windshield. See an autho- WARNING! (Continued) rized dealer for service if your defroster is inoperable. • ALWAYS REMOVE THE EXISTING FLOOR MAT Floor Mat Safety Information FROM THE VEHICLE before installing any other Always use floor mats designed to fit your vehicle.
Page 153: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY 151 Periodic Safety Checks You Should Make Outside WARNING! (Continued) The Vehicle • ALWAYS make sure objects cannot fall or slide into Tires the driver’s side floor area when the vehicle is moving. Objects can become trapped under accelera- Examine tires for excessive tread wear and uneven wear tor, brake, or clutch pedals and could cause a loss of patterns.
Page 155 STARTING AND OPERATING CONTENTS ▫ To Resume Speed ..... .166 STARTING PROCEDURES ....155 ▫...
Page 156 154 STARTING AND OPERATING ▫ Towing This Vehicle Behind Another Vehicle . . .173 EXTENDING YOUR DRIVING RANGE PER CHARGE ......175 DRIVING TIPS .
Page 157: Starting Procedures
STARTING AND OPERATING 155 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both Turn the key to the START position while your vehicle is in inside and outside mirrors, and fasten your seat belts. PARK. When the ignition key is turned to the START and then released to the RUN position, a chime will sound and WARNING! the “READY”...
Page 158: Parking Brake
156 STARTING AND OPERATING NOTE: • If the key is held in the START position for more than 10 seconds “READY” mode will not be achieved. Return the key to the OFF position, and then back to the START position and hold for less than 10 seconds to achieve “READY”.
Page 159: Single-Speed Transmission
STARTING AND OPERATING 157 WARNING! CAUTION! • Never leave children alone in a vehicle, or with If the Brake Warning Light remains on with the park- access to an unlocked vehicle. ing brake released, a brake system malfunction is • Allowing children to be in a vehicle unattended is indicated.
Page 160 158 STARTING AND OPERATING NOTE: • You must press and hold the brake pedal while shifting in or out of PARK. • If all push-button LEDs are on when the key is ON, see an authorized dealer. WARNING! • Only place the transmission into gear when your foot is firmly pressing the brake pedal.
Page 161: Key Ignition Park Interlock
STARTING AND OPERATING 159 • After selecting any gear, wait a moment to allow the WARNING! (Continued) selected gear to engage before accelerating. of reasons. A child or others could be seriously or PARK (P) fatally injured. Children should be warned not to touch the parking brake, brake pedal or the trans- The PARK selection supplements the parking brake by mission range buttons.
Page 162 160 STARTING AND OPERATING NOTE: Refer to the transmission range position displayed WARNING! (Continued) in the instrument cluster and verify that it indicates the should never exit a vehicle while the engine is PARK position. running or the propulsion system is active. Before exiting a vehicle, always come to a complete stop, WARNING! then apply the park brake, shift the transmission into...
Page 163: Auto Park
STARTING AND OPERATING 161 REVERSE (R) CAUTION! (Continued) This range is for moving the vehicle backward. Shift into Disabled Vehicle” in “In Case Of Emergency” for REVERSE only after the vehicle has come to a complete further information. stop. DRIVE (D) NEUTRAL (N) Use this gear for all city and highway driving.
Page 164: Power Steering
162 STARTING AND OPERATING The instrument cluster will display an Auto Shift To Park from providing assist, you will still have the ability to steer message and chime once when Auto Park is activated. the vehicle manually. Mode Of Operation With Key ON: WARNING! Auto Park will be engaged when the transmission is in Continued operation with reduced or no power steer-...
Page 165: Speed Control
STARTING AND OPERATING 163 cluster screen, the vehicle needs to be taken to an autho- rized dealer for service. Refer to “Instrument Cluster Display” in “Getting To Know Your Instrument Panel” for further information. NOTE: • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle.
Page 166: To Activate
164 STARTING AND OPERATING To Activate To Vary The Speed Setting Push the ON/OFF button. The Cruise Indicator Light in To Increase Speed the instrument cluster display will illuminate. To turn the When the Speed Control is set, you can increase speed by system off, push the ON/OFF button a second time.
Page 167: To Accelerate For Passing
STARTING AND OPERATING 165 • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase until the button is released, then the continue to decrease until the button is released, then the new set speed will be established.
Page 168: To Resume Speed
166 STARTING AND OPERATING To Resume Speed Rear Park Assist Sensors To resume a previously set speed, push the RES (+) button The four Rear Park Assist sensors, located in the rear and release. Resume can be used at any speed above fascia/bumper, monitor the area behind the vehicle that is 20 mph (32 km/h).
Page 169: Failure Indications
STARTING AND OPERATING 167 Audible And Visual Signals Supplied By The Rear Park Assist System SIGNAL MEANING INDICATION Obstacle Distance An obstacle is present within the Audible Signal (dashboard loudspeaker) • Sound pulses emitted at a rate that increases as the dis- sensors’...
Page 170: Cleaning The Rear Park Assist System
168 STARTING AND OPERATING • Jackhammers, large trucks, and other vibrations could The sensors and wiring are tested continuously when the ignition is in the ON/RUN position. Failures are indicated affect the performance of Rear Park Assist. immediately if they occur when the system is on. •...
Page 171: Parkview Rear Back Up Camera
STARTING AND OPERATING 169 WARNING! (Continued) CAUTION! (Continued) and blind spots before backing up. You are respon- sensors will not be detected when they are in close sible for safety and must continue to pay attention to proximity. • The vehicle must be driven slowly when using your surroundings.
Page 172 170 STARTING AND OPERATING If your vehicle is equipped with the Camera Delay feature WARNING! and it is turned on, the rear camera image will be displayed for up to ten seconds after the vehicle is shifted out of Drivers must be careful when backing up even when REVERSE unless one of the following conditions occurs: using the ParkView Rear Back Up Camera.
Page 173: Vehicle Loading
STARTING AND OPERATING 171 VEHICLE LOADING Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front Certification Label and rear axles. The load must be distributed in the cargo As required by National Highway Traffic Safety Adminis- area so that the GAWR of each axle is not exceeded.
Page 174: Trailer Towing
172 STARTING AND OPERATING Curb Weight Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way The curb weight of a vehicle is defined as the total weight the brakes operate. of the vehicle with all fluids at full capacity conditions, and with no occupants or cargo loaded into the vehicle.
Page 175: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 173 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Single-Speed Transmission Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED On Trailer NOTE: DRIVING TIPS • When towing your vehicle, always follow applicable Driving On Slippery Surfaces state and provincial laws.
Page 176: Driving Through Water
174 STARTING AND OPERATING • Maintain sufficient distance between your vehicle and WARNING! the vehicle in front of you to avoid a collision in a sudden stop. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front Driving Through Water wheels.
Page 177: Charge
STARTING AND OPERATING 175 Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through shal- result in further damage. Such damage is not covered low standing water, consider the following Caution and by the New Vehicle Limited Warranty. Warning before doing so.
Page 178: Driver Behavior Gauge
176 STARTING AND OPERATING • Power hot or cold temperatures for an extended period, it is recommended that the car be preconditioned using the The needle will move into the Power range when under Uconnect smartphone app (not available in Canada) while acceleration.
Page 179: Range Projection
STARTING AND OPERATING 177 • When both arrows are grey, expect the range to drop Range Projection approximately one mile for each mile driven. This area of the cluster is used to display the projected • When the up arrow is highlighted, expect the range range considering current battery charge and previous energy use.
Page 181 IN CASE OF EMERGENCY CONTENTS HAZARD WARNING FLASHERS ... .180 TIRE SERVICE KIT — IF EQUIPPED ..198 ▫ Tire Service Kit Storage....198 BULB REPLACEMENT .
Page 182: Hazard Warning Flashers
180 IN CASE OF EMERGENCY HAZARD WARNING FLASHERS Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled The Hazard Warning flasher switch is located on the and it is creating a safety hazard for other motorists. instrument panel below the radio.
Page 183 IN CASE OF EMERGENCY 181 Exterior Bulbs Bulb Number Front Low and High Beam Headlamp HIR2LL Front Parking/Daytime Running Lamps W21/5W Front Fog Lamps H11LL Front Side Marker Lamps Front Turn Signal Lamps WY21W Side Direction Lamps WY5W Rear Turn Signal Lamps PY21W Rear Side Marker Lamps Rear Tail and Stop Lamps...
Page 184: Replacing Exterior Bulbs
182 IN CASE OF EMERGENCY Replacing Exterior Bulbs Headlamps Low Beam And High Beam 1. Remove the plastic cap from the back of the headlamp housing. 2. Rotate the bulb counter-clockwise. 3. Remove the bulb and replace as needed. 4. Install the bulb and rotate clockwise to lock in place. 5.
Page 185 IN CASE OF EMERGENCY 183 Front Fog Lamps To replace the front fog lights, see an authorized dealer. Front/Rear Side Marker Lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. 2. Rotate the bulb socket counterclockwise, and remove the bulb and socket assembly from the housing.
Page 186: Replacing Interior Bulbs
184 IN CASE OF EMERGENCY Replacing Interior Bulbs WARNING! (Continued) Rear Cargo Lamp • If a general protection fuse for safety systems (air 1. Using a suitable tool open the light box. bag system, braking system), power unit systems (engine system, transmission system) or steering 2.
Page 187 IN CASE OF EMERGENCY 185 Vehicle Fuse Num- Cavity Mini Fuse Description 7.5 Amp Brown Right Low Beam 5 Amp Tan Front and Rear Ceiling Lights Trunk and Door Courtesy Lights 5 Amp Tan Instrument Panel Node 20 Amp Yellow Central Door Locking 10 Amp Red Diagnostic Socket, Climate Control System,...
Page 188: Power Distribution Center #1
186 IN CASE OF EMERGENCY The fuse for the heated mirrors is located behind an access Power Distribution Center #1 panel on the front of the Instrument Panel. The Power Distribution Center #1 is located on the right side of the underhood compartment. To access the fuses, NOTE: This fuse is a single fuse attached directly to the remove locking screw and slide cover off.
Page 189 IN CASE OF EMERGENCY 187 Cavity Maxi Fuse Mini Fuse Description 60 Amp Blue – Body Control Module (BCM) 20 Amp Yellow – Audio Amplifier 20 Amp Yellow – Ignition Switch 40 Amp Orange – Brake System Module Pump 70 Amp Tan –...
Page 190 188 IN CASE OF EMERGENCY Cavity Maxi Fuse Mini Fuse Description – 20 Amp Yellow Radio – 25 Amp Clear Anti-Lock Brake Valves – 7.5 Amp Brown YAW Sensor – 15 Amp Blue Fog Lamps 30 Amp Green – Electronic Shifter (ESM) 30 Amp Green –...
Page 191: Power Distribution Center #2
IN CASE OF EMERGENCY 189 Power Distribution Center #2 The Power Distribution Center #2 is located next to the battery in the underhood compartment. To access the fuses, pull the release tabs and remove the cover. PDC #2 Cavity Maxi Fuse Mini Fuse Description FPT9...
Page 192: Tire Service Kit - If Equipped
190 IN CASE OF EMERGENCY Cavity Cartridge Fuse Description FPT3 25 Amp White Battery Coolant Pump FPT5 20 Amp Lt. Blue Inverter Coolant Pump FPT6 40 Amp Green Supply for fuses F9, F13, F16, F17 and TIRE SERVICE KIT — IF EQUIPPED Small punctures up to 1/4 inch (6 mm) in the tire tread can be sealed with Tire Service Kit.
Page 193: Tire Service Kit Components And Operation
IN CASE OF EMERGENCY 191 Tire Service Kit Components And Operation Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only. Use the Black Air Pump Hose (7) when selecting this mode. Selecting Sealant Mode Push in the Mode Select Knob (5) and turn to this position to inject the Tire Service Kit Sealant and to...
Page 194 192 IN CASE OF EMERGENCY • When the Tire Service Kit sealant is in a liquid form, optimum operation of the system. Refer to “Sealing A Tire With Tire Service Kit” section (F) “Sealant Bottle clean water and a damp cloth will remove the material And Hose Replacement”.
Page 195: Sealing A Tire With Tire Service Kit
IN CASE OF EMERGENCY 193 WARNING! WARNING! (Continued) in injuries that are serious or fatal to you, your • Do not attempt to seal a tire on the side of the vehicle passengers, and others around you. closest to traffic. Pull far enough off the road to avoid •...
Page 196 194 IN CASE OF EMERGENCY 2. Verify that the valve stem (on the wheel with the 5. Uncoil the Power Plug (8) and insert the plug into the deflated tire) is in a position that is near to the ground. vehicle’s 12 Volt power outlet.
Page 197 IN CASE OF EMERGENCY 195 Select Knob (5) is in the Sealant Mode position and not 2. The pump will start to inject air into the tire immedi- Air Mode. Push the Power Button (4) to turn On the Tire ately after the Sealant Bottle (1) is empty.
Page 198 196 IN CASE OF EMERGENCY 3. Immediately disconnect the Sealant Hose (6) from the WARNING! valve stem, reinstall the cap on the fitting at the end of the hose, and place the Tire Service Kit in the vehicle Tire Service Kit is not a permanent flat tire repair. Have storage location.
Page 199 IN CASE OF EMERGENCY 197 If tire pressure is less than 19 psi (1.3 Bar): 6. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at an authorized dealer as soon as possible. The tire is too badly damaged. Do not attempt to drive the Refer to “(F) Sealant Bottle And Hose Replacement”.
Page 200: Tire Service Kit - If Equipped
198 IN CASE OF EMERGENCY 6. Verify that the cap is installed on the fitting at the end of Tire Service Kit Storage the Sealant Hose (6) and return the hose to its storage The Tire Service Kit is located in the rear cargo area. area (located on the bottom of the air pump).
Page 201: Tire Service Kit Components And Operation
IN CASE OF EMERGENCY 199 Tire Service Kit Components And Operation Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (2) and turn to this position for air pump operation only.
Page 202: Tire Service Kit Usage Precautions
200 IN CASE OF EMERGENCY • The Sealant Bottle (4) and Sealant Hose (3) are a one tire Using The Deflation Button application use and need to be replaced after each use. Push the Deflation Button (9) to reduce the air Always replace these components immediately at your pressure in the tire if it becomes over-inflated.
Page 203: Sealing A Tire With Tire Service Kit
IN CASE OF EMERGENCY 201 WARNING! WARNING! (Continued) in injuries that are serious or fatal to you, your • Do not attempt to seal a tire on the side of the vehicle passengers, and others around you. closest to traffic. Pull far enough off the road to avoid •...
Page 204 202 IN CASE OF EMERGENCY 2. Verify that the valve stem (on the wheel with the 5. Uncoil the Power Plug (7) and insert the plug into the deflated tire) is in a position that is near to the ground. vehicle’s 12 Volt power outlet.
Page 205 IN CASE OF EMERGENCY 203 Select Knob (2) is in the Sealant Mode position and not 2. The pump will start to inject air into the tire immedi- Air Mode. Push the Power Button (1) to turn On the Tire ately after the Sealant Bottle (4) is empty.
Page 206 204 IN CASE OF EMERGENCY 3. Immediately disconnect the Sealant Hose (3) from the WARNING! valve stem, reinstall the cap on the fitting at the end of the hose, and place the Tire Service Kit in the vehicle Tire Service Kit is not a permanent flat tire repair. Have storage location.
Page 207 IN CASE OF EMERGENCY 205 If tire pressure is less than 19 psi (1.3 Bar): 6. Replace the Sealant Bottle (4) and Sealant Hose (3) assembly at an authorized dealer as soon as possible. The tire is too badly damaged. Do not attempt to drive the Refer to “(F) Sealant Bottle And Hose Replacement”.
Page 208: Jump Starting Procedure (12 Volt Battery Only)
206 IN CASE OF EMERGENCY 6. Verify that the cap is installed on the fitting at the end of CAUTION! the Sealant Hose (3) and return the hose to its storage area (located on top of the housing). Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 7.
Page 209: Jump Starting Procedure
IN CASE OF EMERGENCY 207 WARNING! WARNING! • Take care to avoid the radiator cooling fan whenever Do not allow vehicles to touch each other as this could establish a ground connection and personal injury the hood is raised. It can start anytime the ignition could result.
Page 210: Manual Park Release
208 IN CASE OF EMERGENCY 3. Connect the negative end (-) of the jumper cable to the 2. Disconnect the negative end (-) of the jumper cable from negative (-) post of the booster battery. the negative (-) post of the booster battery. 4.
Page 211 IN CASE OF EMERGENCY 209 Manual Park Release is available. If a dead 12 volt battery is the cause of the condition refer to “Jump Starting Procedure — 12 Volt Battery” before performing the Manual Park Release. To perform the Manual Park Release follow these steps: 1.
Page 212: Freeing A Stuck Vehicle
210 IN CASE OF EMERGENCY FREEING A STUCK VEHICLE WARNING! (Continued) If your vehicle becomes stuck in mud, sand or snow, it can injure someone. Do not spin your vehicle’s wheels often be moved using a rocking motion. Turn the steering faster than 30 mph (48 km/h) or for longer than 30 wheel right and left to clear the area around the front seconds continuously without stopping when you are...
Page 213: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 211 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheels OFF The Ground Single-Speed Transmission Flat Tow NONE NOT ALLOWED Wheel Lift or Dolly Tow Rear NOT ALLOWED Front...
Page 214: Enhanced Accident Response System (Ears)
212 IN CASE OF EMERGENCY ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System. Please refer to “Occupant Restraint Systems” in “Safety” for further information on the Enhanced Accident Re- sponse System (EARS) function. EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR).
Page 215 SERVICING AND MAINTENANCE CONTENTS ▫ Power Electronics And Battery Thermal SCHEDULED SERVICING ....215 Management Systems — Drain, Flush And ▫ Maintenance Plan..... . .215 Refill.
Page 216 214 SERVICING AND MAINTENANCE ▫ Spare Tires — If Equipped ....243 BODYWORK ......251 ▫...
Page 217: Scheduled Servicing
SERVICING AND MAINTENANCE 215 SCHEDULED SERVICING At Every Service Interval: Once A Month Or Before A Trip: • Rotate the tires. Rotate at the first sign of irregular • Check windshield washer fluid level wear. • Check the tire inflation pressures and look for unusual •...
Page 218 216 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Inspect the brake linings. Replace as necessary. Inspect parking brake function. Adjust as necessary. Additional Maintenance Replace cabin air filter. Clean and lube sun roof tracks. Flush and replace the coolant in the Power Electronics and Battery Thermal Loop Systems at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 219: Underhood Compartment
SERVICING AND MAINTENANCE 217 UNDERHOOD COMPARTMENT 1 — Battery Thermal Coolant Reservoir 4 — Fuses 2 — Power Electronics Coolant Reservoir 5 — 12V Battery 3 — Brake Fluid Reservoir 6 — Washer Fluid Reservoir Adding Washer Fluid WARNING! The windshield washer fluid reservoir is located in the Commercially available windshield washer solvents underhood compartment, and the fluid level should be are flammable.
Page 220: Maintenance-Free Battery 12 Volt
218 SERVICING AND MAINTENANCE Maintenance-Free Battery 12 Volt WARNING! (Continued) Your vehicle is equipped with a maintenance-free 12 Volt • The battery in this vehicle has a vent hose that battery. You will never have to add water, nor is periodic should not be disconnected and should only be maintenance required.
Page 221: Dealer Service
SERVICING AND MAINTENANCE 219 DEALER SERVICE CAUTION! • Failure to properly maintain your vehicle or perform WARNING! repairs and service when necessary could result in Your vehicle has both a high voltage DC and AC more costly repairs, damage to other components or system as well as a 12 Volt system.
Page 222: Power Electronics And Battery Thermal Management Systems - Coolant Level Check
220 SERVICING AND MAINTENANCE Power Electronics And Battery Thermal When additional coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottles. Management Systems — Coolant Level Check Do not overfill. The coolant expansion bottles provides a quick visual method for determining that the coolant level is adequate.
Page 223: Power Electronics And Battery Thermal Management Systems - Cooling Pressure Caps
SERVICING AND MAINTENANCE 221 Power Electronics And Battery Thermal Management Systems — Cooling Pressure Caps The caps must be fully tightened to prevent loss of coolant (antifreeze). The caps should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. NOTE: •...
Page 224: Selection Of Coolant
222 SERVICING AND MAINTENANCE WARNING! (Continued) CAUTION! (Continued) • Do not use a pressure cap other than the one speci- • Do not use water alone or alcohol-based coolant fied for your vehicle. Personal injury or vehicle (antifreeze) products. Do not use additional rust damage may result.
Page 225: Power Electronics And Battery Thermal Management Systems - Drain, Flush And Refill
SERVICING AND MAINTENANCE 223 When adding coolant (antifreeze): Power Electronics And Battery Thermal Management Systems — Drain, Flush And Refill • The manufacturer recommends using Mopar Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Refer to “Scheduled Servicing” for the proper maintenance Formula OAT (Organic Additive Technology).
Page 226: Points To Remember
224 SERVICING AND MAINTENANCE containers or allow it to remain in puddles on the ground. added, contents of coolant recovery bottles must also be If ingested by a child, contact a physician immediately. protected against freezing. Clean up any ground spills immediately. •...
Page 227: Body Lubrication
SERVICING AND MAINTENANCE 225 Body Lubrication WARNING! Locks and all body pivot points, including such items as • Use only refrigerants and compressor lubricants ap- seat tracks, door hinge pivot points and rollers, liftgate, proved by the manufacturer for your air conditioning tailgate, decklid, sliding doors and hood hinges, should be system.
Page 228 226 SERVICING AND MAINTENANCE Operation of the wipers on dry glass for long periods may If a wiper blade or wiper arm is damaged, replace the cause deterioration of the wiper blades. Always use washer affected wiper arm or blade with a new unit. Do not fluid when using the wipers to remove salt or dirt from a attempt to repair a wiper arm or blade that is damaged.
Page 229: Brake System
SERVICING AND MAINTENANCE 227 NOTE: The rear wiper arm cannot be raised fully upward 4. Install the wiper blade pivot pin into the wiper blade unless the pivot cap is raised first. holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place.
Page 230: Raising The Vehicle
228 SERVICING AND MAINTENANCE Be sure to clean the top of the master cylinder area before WARNING! (Continued) removing the cap. If necessary, add fluid to bring the fluid in a tightly closed container. Keep the master cylin- level up to the requirements described on the brake fluid der reservoir cap secured at all times.
Page 231: Tires
SERVICING AND MAINTENANCE 229 TIRES NOTE: • P (Passenger) — Metric tire sizing is based on U.S. Tire Safety Information design standards. P-Metric tires have the letter “P” Tire safety information will cover aspects of the following molded into the sidewall preceding the size designation. information: Tire Markings, Tire Identification Numbers, Tire Example: P215/65R15 95H.
Page 232 230 SERVICING AND MAINTENANCE Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 233 SERVICING AND MAINTENANCE 231 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 234 232 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 235 SERVICING AND MAINTENANCE 233 Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 236 234 SERVICING AND MAINTENANCE Steps For Determining Correct Load Limit— Metric Example For Load Limit (1) Locate the statement “The combined weight of For example, if “XXX” amount equals 635 kg and there will occupants and cargo should never exceed XXX kg or be five 68 kg passengers in your vehicle, the amount of XXX lbs.”...
Page 237 SERVICING AND MAINTENANCE 235 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 238: Tires - General Information
236 SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 239 SERVICING AND MAINTENANCE 237 Battery Consumption CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher battery charge consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 240 238 SERVICING AND MAINTENANCE pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 241 SERVICING AND MAINTENANCE 239 Run Flat Tires — If Equipped WARNING! Run Flat tires allow you the capability to drive 50 miles Fast spinning tires can be dangerous. Forces generated (80 km) at 50 mph (80 km/h) after a rapid loss of inflation by excessive wheel speeds may cause tire damage or pressure.
Page 242 240 SERVICING AND MAINTENANCE Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure - Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 243 SERVICING AND MAINTENANCE 241 Keep dismounted tires in a cool, dry place with as little It is recommended you contact an authorized tire dealer or exposure to light as possible. Protect tires from contact with original equipment dealer with any questions you may oil, grease, and gasoline.
Page 244: Tire Types
242 SERVICING AND MAINTENANCE Summer Or Three Season Tires — If Equipped WARNING! (Continued) Summer tires provide traction in both wet and dry condi- • Failure to equip your vehicle with tires having ad- tions, and are not intended to be driven in snow or on ice. equate speed capability can result in sudden tire If your vehicle is equipped with Summer tires, be aware failure and loss of vehicle control.
Page 245: Spare Tires - If Equipped
SERVICING AND MAINTENANCE 243 Snow Tires Spare Tires — If Equipped Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 246 244 SERVICING AND MAINTENANCE Compact Spare Tire — If Equipped WARNING! (Continued) The compact spare is for temporary emergency use only. You more than 50 mph (80 km/h). Temporary use spares can identify if your vehicle is equipped with a compact spare have limited tread life.
Page 247 SERVICING AND MAINTENANCE 245 Do not install a wheel cover or attempt to mount a Limited Use Spare — If Equipped conventional tire on the collapsible spare wheel, since the The limited use spare tire is for temporary emergency use wheel is designed specifically for the collapsible spare tire.
Page 248: Wheel And Wheel Trim Care
246 SERVICING AND MAINTENANCE Wheel And Wheel Trim Care CAUTION! (Continued) All wheels and wheel trim, especially aluminum and Limited Warranty. Only car wash soap, Mopar Wheel chrome plated wheels, should be cleaned regularly using Cleaner or equivalent is recommended. mild (neutral Ph) soap and water to maintain their luster and to prevent corrosion.
Page 249: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 247 NOTE: If you intend parking or storing your vehicle for an Tire Chains (Traction Devices) extended period after cleaning the wheels with wheel Use of traction devices require sufficient tire-to-body clear- cleaner, drive your vehicle and apply the brakes to remove ance.
Page 250: Tire Rotation Recommendations
248 SERVICING AND MAINTENANCE CAUTION! CAUTION! (Continued) operating speed of the device manufacturer’s if it is To avoid damage to your vehicle or tires, observe the less than 30 mph (48 km/h). following precautions: • Do not use traction devices on a compact spare tire. •...
Page 251: Department Of Transportation Uniform Tire Quality Grades
SERVICING AND MAINTENANCE 249 The front and rear wheels are different sizes and cannot be All passenger vehicle tires must conform to Federal used in place of each other. Rotate the wheels “side-to- safety requirements in addition to these grades. side”...
Page 252: Temperature Grades
250 SERVICING AND MAINTENANCE WARNING! WARNING! The traction grade assigned to this tire is based on The temperature grade for this tire is established for straight-ahead braking traction tests, and does not a tire that is properly inflated and not overloaded. include acceleration, cornering, hydroplaning, or Excessive speed, under-inflation, or excessive load- peak traction characteristics.
Page 253: Bodywork
SERVICING AND MAINTENANCE 251 BODYWORK Body And Underbody Maintenance Protection From Atmospheric Agents Cleaning Headlights Vehicle body care requirements vary according to geographic Your vehicle is equipped with plastic headlights and fog locations and usage. Chemicals that make roads passable in lights that are lighter and less susceptible to stone breakage snow and ice and those that are sprayed on trees and road than glass headlights.
Page 254: Interiors
252 SERVICING AND MAINTENANCE • Use a high quality cleaner wax, such as Mopar Cleaner • If your vehicle is damaged due to a collision or similar Wax to remove road film, stains and to protect your cause that destroys the paint and protective coating, have paint finish.
Page 255: Plastic And Coated Parts
SERVICING AND MAINTENANCE 253 Seat Belt Maintenance Plastic And Coated Parts Do not bleach, dye or clean the belts with chemical solvents Use Mopar Total Clean to clean vinyl upholstery. or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. CAUTION! If the belts need cleaning, use a mild soap solution or •...
Page 256: Leather Parts
254 SERVICING AND MAINTENANCE Leather Parts CAUTION! Mopar Total Clean is specifically recommended for leather Do not use Alcohol and Alcohol-based and/or Ketone upholstery. based cleaning products to clean leather upholstery, as Your leather upholstery can be best preserved by regular damage to the upholstery may result.
Page 257 TECHNICAL SPECIFICATIONS CONTENTS VEHICLE IDENTIFICATION NUMBER ..256 FLUID CAPACITIES ..... .259 BRAKE SYSTEM ......257 FLUIDS AND LUBRICANTS .
Page 258: Vehicle Identification Number
256 TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears engraved on the right front door sill, under the sill scuff plate, on an adhesive label applied to the right door opening on the B-Pillar, on the vehicle registration and title.
Page 259: Brake System
TECHNICAL SPECIFICATIONS 257 BRAKE SYSTEM Torque Specifications In the event regenerative braking or power assist is lost for Lug Nut/Bolt Torque **Lug Nut/ Lug Nut/ any reason the brakes will still function. The effort required Bolt Size Bolt Socket to brake the vehicle will be significantly more than that Size required with the power system operating.
Page 260 258 TECHNICAL SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Torque Patterns After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against Wheel Mounting Surface the wheel.
Page 261: Fluid Capacities
TECHNICAL SPECIFICATIONS 259 FLUID CAPACITIES Systems U.S. Metric Power Electronics Cooling System 3.6 Quarts 3.4 Liters Battery Thermal Management Cooling System 7.0 Quarts 6.6 Liters Single-Speed Transmission 0.8 Quart 750 ml FLUIDS AND LUBRICANTS Component Fluids And Lubricants Coolant Mopar Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technol- ogy) or equivalent meeting the requirements of FCA Ma- terial Standard MS.90032.
Page 262 260 TECHNICAL SPECIFICATIONS CAUTION! • Mixing of coolant (antifreeze) other than specified Organic Additive Technology (OAT) coolant (anti- freeze), may result in cooling system damage and may decrease corrosion protection. Organic Additive Technology (OAT) coolant is different and should not be mixed with Hybrid Organic Additive Tech- nology (HOAT) coolant (antifreeze).
Page 263 MULTIMEDIA CONTENTS UCONNECT SYSTEMS ....262 UCONNECT 3/3 NAV VOICE RECOGNITION QUICK TIPS ......276 CYBERSECURITY .
Page 264: Uconnect Systems
262 MULTIMEDIA UCONNECT SYSTEMS The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent For detailed information about your Uconnect system, version of vehicle software (such as Uconnect software) is refer to your Uconnect Owner’s Manual Supplement. installed.
Page 265: Uconnect Settings
MULTIMEDIA 263 NOTE: UCONNECT SETTINGS • FCA US LLC or your dealer may contact you directly The Uconnect system uses a combination of buttons on the regarding software updates. touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access •...
Page 266: Customer Programmable Features - Uconnect 3/3 Nav Display Settings
264 MULTIMEDIA Customer Programmable Features — Uconnect 3/3 mode, press and release the preferred setting and make your selection. Once the setting is complete, either press NAV Display Settings the back arrow button on the touchscreen or push the back Push the Settings button on the faceplate, to display button on the faceplate to return to the previous menu.
Page 267 MULTIMEDIA 265 Setting Name Selectable Options Brightness – Language English Français Español Touchscreen Beep Charge Low Pop-Up NOTE: When in the “Charge Low Pop-Up” display, you may turn on or shut off a low charge indicator. Units After pressing the “Units” button on the touchscreen, you may select each unit of measure independently displayed in the instrument cluster display.
Page 268 266 MULTIMEDIA After pressing the “Custom” button on the touchscreen, you may select from the following menu items: Setting Name Selectable Options Distance Pressure Temperature °C °F Energy MPGe km/kWH mi/kWh KM/Le Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 269 MULTIMEDIA 267 Clock & Date After pressing the “Clock & Date” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Set Time and Format 12 hour 24 hour NOTE: Press the corresponding arrow above and below the current time to adjust, then select “AM” or “PM.” Show Time Status Set Date Set Date...
Page 270 268 MULTIMEDIA Charging Schedule To set up a charging schedule, press the “More” or “Set- tings” button on the touchscreen. Setting Name Selectable Options Enable Schedule NOTE: Continue setting up the schedule, picking from the following menus: • Weekdays or Weekends •...
Page 271 MULTIMEDIA 269 Setting Name Selectable Options ParkView Backup Camera Fixed Guide Lines — If Equipped NOTE: When this feature is enabled, fixed (static) grid lines are overlaid on the Rear Backup Camera image to illus- trate the width of the vehicle. Lights After pressing the “Lights”...
Page 272 270 MULTIMEDIA Setting Name Selectable Options Remote Door Unlock/Door Unlock Driver NOTE: When “Driver” is selected, only the driver’s door will unlock on the first push of the key fob unlock button, you must push the key fob unlock button twice to unlock the passenger’s doors. When “All” is selected, all of the doors will unlock on the first push of the key fob unlock button.
Page 273 MULTIMEDIA 271 Setting Name Selectable Options Balance/Fade When in the “Balance/ Fade” display, you may adjust the Balance settings. Auto-On Radio Recall Last NOTE: When the “Auto-On Radio” feature is selected, the radio automatically turns on when the vehicle is in RUN or recalls whether it was on or off at last ignition off.
Page 274 272 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: “Tune Start” begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 275 MULTIMEDIA 273 Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings NOTE: When the “Restore Settings” feature is selected it will reset the Display, Clock, Audio, and Radio Settings to their default settings.
Page 276: Steering Wheel Audio Controls
274 MULTIMEDIA STEERING WHEEL AUDIO CONTROLS Pushing the center button makes the radio switch between the various modes available (AM/FM/SAT/AUX/Media The remote sound system controls are located on the rear Player, etc.) and can also be used to select/enter an item surface of the steering wheel.
Page 277: Ipod/Usb/Media Player Control - If Equipped
MULTIMEDIA 275 current track, or to the beginning of the previous track if it RADIO OPERATION AND MOBILE PHONES is within eight seconds after the current track begins to Under certain conditions, the mobile phone being on in play. your vehicle can cause erratic or noisy performance from your radio.
Page 278: Telematics Modem
276 MULTIMEDIA TELEMATICS MODEM Changes or modifications not expressly approved by the party responsible for compliance could void the user’s Your vehicle is equipped with a 3G CDMA cellular modem authority to operate the equipment. to connect the vehicle with your device to provide the following features: UCONNECT 3/3 NAV VOICE RECOGNITION QUICK •...
Page 279: Get Started
MULTIMEDIA 277 Get Started 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instruc- tions. 2. Reduce background noise. Wind and passenger conver- sations are examples of noise that may impact recogni- tion. 3. Speak clearly at a normal pace and volume while facing straight ahead.
Page 280: Basic Voice Commands
278 MULTIMEDIA Basic Voice Commands Radio The basic Voice Commands below can be given at any Use your voice to quickly get to the AM, FM or SiriusXM point while using your Uconnect system. Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button .
Page 281: Media
MULTIMEDIA 279 Media Uconnect offers connections via USB, Bluetooth and Aux- iliary ports (if equipped). Voice operation is only available for connected USB and iPod devices. Push the VR button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist.
Page 282: General Information
280 MULTIMEDIA • “ Redial (call previous outgoing phone number)” General Information • “ Call back (call previous incoming phone number)” The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: TIP: When providing a Voice Command, push the Phone This device complies with Part 15 of the FCC Rules and (if active) or VR button and say “...
Page 283: Cd/Dvd Disc Maintenance
MULTIMEDIA 281 CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: • Handle the disc by its edge; avoid touching the surface. • If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
Page 285 CUSTOMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ......284 Impaired (TDD/TTY) .
Page 286: Suggestions For Obtaining Service For Your Vehicle
284 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 287: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 285 Any communication to the manufacturer’s customer center In Mexico Contact should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 288: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
286 CUSTOMER ASSISTANCE Customer Assistance For The Hearing Or Speech questions about the service contract, call the manufactur- er’s Service Contract National Customer Hotline at 1-800- Impaired (TDD/TTY) 521-9922 (Canadian residents, call (800) 465-2001 English / To assist customers who have hearing difficulties, the (800) 387-9983 French).
Page 289: Warranty Information
CUSTOMER ASSISTANCE 287 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 290: In Canada
288 CUSTOMER ASSISTANCE In Canada Diagnostic Procedure Manuals If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department imme- charts and detailed illustrations. These practical manuals diately.
Page 291 INDEX...
Page 292 290 INDEX Adding Washer Fluid......217 Alarm System Air Bag ....... . .122 Security Alarm .
Page 293 INDEX 291 Parking .......156 How To Stow An unused ALR Seat Belt ..143 Warning Light .
Page 294 292 INDEX Diagnostic System, Onboard....98 Exterior Lights ......56, 151 Dimmer Switch Headlight .
Page 295 INDEX 293 Headlights ....... .56 Interior Lighting ......59 Cleaning .
Page 296 294 INDEX Brake Warning ......91 Lug Nuts/Bolts ......257 Bulb Replacement .
Page 297 INDEX 295 Owner’s Manual (Operator Manual) ...4, 288 Reminder, Lights On ......56 Reminder, Seat Belt .
Page 298 296 INDEX Extender .......117 Service Manuals ......288 Front Seat .
Page 299 INDEX 297 Sun Roof ....... . .73 Rotation .......248 Supplemental Restraint System - Air Bag .
Page 300 298 INDEX Uconnect Washer Uconnect Settings ......263 Adding Fluid ......217 Uniform Tire Quality Grades .
Page 301 INSTALLATION OF RADIO TRANSMITTING Mobile radio equipment with output power greater than EQUIPMENT normal may require special precautions. Special design considerations are incorporated into this All installations should be checked for possible interfer- vehicle’s electronic system to provide immunity to radio ence between the communications equipment and the frequency signals.

Fiat 500e 2018 Owner's Manual

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Servicing and Maintenance

Technical Specifications

Multimedia

Customer Assistance

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Fiat 500e 2018

Summary of Contents for Fiat 500e 2018