AT&T Trimline 210 User Manual

Table/desk installation Table/desk installation
This telephone includes a 7-foot line cord with a
6 Check for dial tone
modular plug on each end. Use this cord to
Lift the handset and listen for dial tone. If you
connect the telephone to a modular wall jack. cannot hear a dial tone, refer to In case of
difficulty and try to correct the problem. To
1 Fill in directory card
disconnect the telephone, squeeze the clip on
Remove the directory card and write in
the modular plug and pull it out of the jack.
your own telephone number. Also write the
telephone numbers (or names) that you want
to store in each memory location. Reinstall
the card and clear plastic cover.
2 Connect line cord to
telephone
Plug the long line cord into
the jack on the underside of
the telephone base. Then,
feed the line cord through
the channel provided so the
telephone sits flat on your
table or desk during use
(Figure 1).
3 Connect line cord to wall
Figure 1
jack
Plug free end of the line cord
into a modular wall jack. Make
sure it snaps firmly into place.
4 Set dial mode switch
This product comes set in the
tone (TT) mode. Make sure
you choose the correct dialing
method (TT or DP); touch
tone dialing will not work if
you have dial pulse service.
(Figure 2) Figure 2
5 Connect handset to base
Plug one end of the coiled handset cord into
the handset, and the other end into the base.
Then, hang up.
1 2
Wall installation Wall installation
1 Fill in directory card 3 Plug the line cord into the
Remove the directory card and write in jack on the underside of
your own telephone number. Also write the the base. Feed the line cord
telephone numbers (or names) that you want into the channel and wind it
to store in each memory location. around the mounting area.
Feed the last portion (as short
2 Reverse handset tab
as possible), through one of
To install the telephone on a wall jack, you
the slots in the mounting area
must reverse the small tab beneath the
(Figure 2).
directory card. This tab holds the handset in
place when you hang up. 4 Install telephone base on
wall jack
Remove the directory card and plastic
Hold the base up
cover. Use a paper clip to lift and remove the
next to the wall
handset tab. Reverse the tab and reinstall
jack, and plug in the
it, as shown (Figure 1). Then, replace the
line cord (Figure 3).
directory card and cover.
Then, push the base
against the wall jack
and down until it is
held securely by the
mounting studs.
NOTE: If you
cannot fit the base
onto the wall jack,
remove the four
Figure 3
non-slip pads.
5 Set dial mode switch
Refer to Step 4 under Table/desk installation.
Figure 1
3 4
Wall installation Operation
6 Connect handset to telephone Redial
Connect one end of the coiled handset cord
This telephone stores the last phone number
into the base. Plug the other end into the
dialed in redial memory. However, if the phone
handset (Figure 4). Then, hang up.
is disconnected from the wall jack or if you are
without phone service for more than 30 minutes,
redial memory will be lost.
The redial memory can accept numbers up to
31 digits long. The number will remain in redail
memory until you change it by dialing another
Figure 2
telephone number.
To dial the same number again, lift the handset,
and press
NOTE: If the number is more than 31 digits
Figure 4
long, no digits will be stored in the redial memory.
7 Check for dial tone
Lift the handset and listen for dial tone. If you
cannot hear a dial tone, refer to In case of
Erasing redial
difficulty and try to correct the problem.
For privacy, you can erase the redial memory. Lift
the handset, then press
Flash
Press
to activate custom calling services such as call
waiting or 3-way calling.
You may have to press other buttons before
or after
instructions provided by your local telephone
company.
Mute
While on a call, press
microphone. The other party cannot hear you,
but you can hear the other party.
Press
conversation.
5
Operation
Ringer volume
The ringer volume switch allows you to turn the
telephone ringer OFF, or set it to ring at LO or
HI volume. You can dial or answer calls normally
when the ringer is off. Other telephones in your
home will still ring; they are not affected by the
switch.
Ringer tone
You can choose from three different ringer
tones. The phone comes set to Tone 2.
.
1 Press .
2 Press .
3 Press for Tone 1
-OR-
Press for Tone 2
-OR-
and hang up.
Press for Tone 3
-OR-
Press to temporarily turn off the ringer.
instead of pressing the switchhook
Lifting the handset and replacing it onto the
base will turn the ringer back on.
Receiver (handset) volume
, as explained in custom calling
The receiver volume switch on the side of the
handset can be adjusted for a comfortable
listening level. The switch has three volume
positions.
to mute the
again to return to two-way
6 7
Operation
Temporary tone dialing
Temporary tone dialing is used only when you
have rotary service. It allows you to access to
services that require tone signaling, including
some tone-activated computer systems (e.g.,
telephone banking).
To change from pulse (rotary) to tone dialing
during a call:
1 Dial a telephone number with the dial switch
set to DP (pulse).
2 Press ; all buttons pressed after this will
send tone signals.
3 After you hang up, the phone automatically
returns to rotary service.
8