Security Command SC Series User Manual page 2

Your Security Command® Keypad
ARMED STAY ZONES 1 TO 4
READY
TROU BLE
READY ARMED 1 2 3
TRBL STAY
POWER INSTANT
POW ER
STAY I N STANT BYPASS CODE
IN STANT
1 2 3 4
A BC D E F G H I
6 8
5 7
MN O P Q R STU
9 0
SPECIAL COMMAND
Y Z
BUILT-IN ALERT SPECIAL KEY
How the Lights Operate
Pulse - 1 second on, 1 second off
Flash - 1/2 second on, 1/2 second off
Rapid Flash - 1/4 second on, 1/4 second off
Wink - 1/4 second on, 1 3/4 seconds off
READY
On: The system is ready to be armed.
Off: The system is armed or a burglary zone is faulted.
Rapid Flash: An alarm has occurred and the system is disarmed.
TROUBLE
Off: The system is operating correctly.
Pulse: The system is unable to report to the supervising panel.
POWER
On: Main power is okay.
Off: Main power is disconnected.
Pulse: Low battery.
ARMED
On: Perimeter or Interior are armed.
Off: Perimeter and Interior are off.
Rapid Flash: An alarm has occurred and the system is armed.
Pulse: The system is armed and exit delay is occurring.
STAY
On: Only the Perimeter is armed.
Off: All areas are armed or disarmed.
INSTANT
On: The system is instant armed with no entry delay.
Off: The system is armed with entry/exit delays or is disarmed.
ZONE
On: The zone is disarmed and faulted.
Off: The zone is normal.
Rapid Flash: A zone is in alarm. This ß ashes until the zone is disarmed
and a user code is entered a second time.
Wink: The zone is bypassed.
Pulse: The zone is in a trouble or zone monitor condition.
How the Alert Tone Operates
Burglary Siren
Fire Siren
Steady Tone
4
FUNC TION KEYS 1 Short Beep
4 Short Beeps
NUMBER KEYS
J K L
VW X
Your system provides up to eight user codes. Each code consists of three
parts:
COMMAND KEY
The User Number is how the system identiÞ es a user.
The User Code is the 4-digit number a user enters into the keypad to arm
and disarm the system and to perform other system operations.
User Level - There are three user levels: Users 01 through 06 are always
Standard level. User 07 is always Master level and 08 is Full Master level.
A Standard level user can perform all user functions except adding,
deleting, or changing other user codes. A Standard level user can change
their own code. User 07 is a Master level that can perform all user
functions including adding, deleting and changing user codes 01 through
07. User 08 Full Master level can perform all user functions including
adding, deleting and changing all user codes, 01 through 08.
Arming the System
When the READY light is on, arm the system using one of the methods
listed below.
Enter Your Code or press COMMAND and 1 to arm all areas.
Press STAY to arm only the Perimeter.
To arm the system without any exit or entry delays, press the INSTANT key
before starting the arming sequence or after (pulsing READY light).
You may force arm the system while one of your burglary protection zones
is faulted (door open). Hold the last key pressed for 2 seconds: The keypad
beeps once. When the zone returns to a normal condition (door closes),
the zone becomes part of the armed system again.
Disarming the System
When the ARMED light is on, enter Your Code to disarm all areas. Enter
your code again to clear any zone alarm memory (rapidly ß ashing lights).
Disarming During an Alarm
When the ARMED light is on and a zone is in alarm, enter Your Code to
silence the alarm and disarm the system. Enter Your Code again to clear
any zone alarm memory (rapidly ß ashing lights).
Easy Exit
This function allows you to exit while the Perimeter is armed. Press
BYPASS or press COMMAND and 9 to restart the exit delay. The perimeter
arms when the exit delay expires or when the BYPASS key is pressed a
sceond time.
A burglary alarm condition on zones 1, 2, or 3.
A Þ re alarm condition on zone 4.
A trouble condition on the system or a Þ re zone.
Pressing any key silences a steady alert tone.
A valid function was entered.
An incorrect value was entered.
User Codes
Arming and Disarming Your System
Security Command Functions
Bypassing a Zone
Bypassing means the system ignores events that occur on the zone.
You can bypass a disarmed zone, such as a patio door, so it can be used
while the rest of the Perimeter protection is turned on. Use 2-digit zone
numbers: 01, 02, 03. Zone 4 is a 24-hour zone and cannot be manually
bypassed.
Press BYPASS, enter Your Code, and then the zone number to bypass the
zone. If the zone is already bypassed, pressing BYPASS, entering Your
Code, and the zone number puts the zone into normal condition.
Resetting Sensors
Use this function to reset smoke detectors after an alarm when the Þ re
zone light is ß ashing in alarm memory.
Press COMMAND followed by 4 then 7 or simply enter Your Code. The
system resets the smoke detectors and stops the ß ashing light if the zone
restores to normal.
Note: Your system may not be conÞ gured for Zone 4 as a Fire zone.
Testing the System
It is good practice to test your system at least once each week. This
assures you that the system is working correctly and identiÞ es any
potential problems.
Press COMMAND followed by 4 then 1. The bell rings and the internal
speaker beeps for 1 second.
Monitoring Zones
You can monitor zones in the system so that the keypad emits a short door
bell tone any time that zone faults.
To only monitor a speciÞ c zone, press COMMAND and 6, enter Your Code,
then enter the 2-digit zone number (01, 02, 03).
To monitor all Perimeter zones, press COMMAND and 6, enter Your Code,
then press STAY.
To monitor Perimeter/Interior zones, press COMMAND and 6, enter Your
Code, then press SPECIAL.
Repeat to remove a zone from monitor mode.
User Codes
This function allows a user to add, change, or delete a user code from the
system. The User Codes section to the left contains information about the
User Codes available on your system.
Add or Change a User Code
Press CODE and enter Your Code. Enter the new user number and
user code.
CODE (key) + Your Code + # # + c c c c
Delete a User Code
Press CODE and enter Your Code. Enter the user number and four
zeroes (0 0 0 0) to delete a user code.
CODE (key) + Your Code + # # + 0 0 0 0
## = 2-digit user number c = new user code
To add/change a user code.
To delete a user code.
0 = zero key