Related Manuals for Wolf I363418
Summary of Contents for Wolf I363418
- Page 2 Before you begin installation, read information is important for the safe The correct voltage, frequency and these instructions completely and and efficient installation of the Wolf amperage must be supplied to the carefully. Pro Series island hood. appliance from a dedicated, ground- •...
- Page 3 To center of To center of Hood plate hood transition transition of hood • 16-gauge stainless steel shell (side of hood) (back of hood) I363418 18” 36” 8.75” 9” 6.5” • Transition with backdraft damper included I423418 24” 42” 8.75”...
-
Page 4: Important Notes
(included with hood). In cold weather installations a back-draft damper is necessary to minimize the backflow of cold air into the room. 4) Wolf recommends the hood be installed 30”-36” above the cooking surface. 5) Local building codes may require the use of make-up air. -
Page 5: Installation
Dimensions in parentheses are in millimeters. Shipping Weights for Blowers Shipping Weights for Island Hoods Part Shipping Blower Number Weight Model Number Shipping Weight CTBLOWER-60REM 801640 35 lbs. I363418 88 lbs. CTBLOWER-90REM 801641 35 lbs. I423418 96 lbs. CTBLOWER-120REM 801642 39 lbs. I543418 116 lbs. -
Page 6: Important Note
1) Decide where the ductwork will shell. run between the hood and the 2) Remove center filter bank by outside of the home. Your Wolf island removing the 2 screws from each hood has a top discharge which will side. DO NOT DISCARD THESE run vertically. -
Page 7: Tighten Screws
E R I E S S L A N D O O D N S T A L L A T I O N I N S T A L L H O O D 7) Lift the hood and align hood CAUTION mounting holes with pre-drilled ceil Framing must be structurally... - Page 8 E R I E S S L A N D O O D N S T A L L A T I O N I N S T A L L T H E W I R I N G I N T E R N A L B L O W E R WARNING This ventilation hood must be pro-...
- Page 9 E R I E S S L A N D O O D N S T A L L A T I O N R E M O T E B L O W E R IMPORTANT NOTE: Before turning STEP 2: Connect Remote Blower Feed 20”of (ROMEX) power cable through the knockout opening hole...
- Page 10 For your tion, ducting, electrical place- 2) Remove all packaging material convenience, Wolf has created a tem- ment and adequacy of mounting from filters and drip cups. surfaces. plate for a standardized logo location.
- Page 11 B L O W E R S D U C T C O V E R S Internal Blowers External Blowers Stainless steel duct covers are avail- able in 6 and 12 inches for all Wolf • IBLOWER-120INT (804703) – • CTBLOWER-60REM (801640) –...
- Page 12 A S S E M B L I E S Copper Finish: Platinum Finish: Decorative rail assemblies are available • RAIL-36/COP – Decorative rail for 36" for Wolf island hoods in stainless steel, • RAIL-36/PLT – Decorative rail for 36" island hoods. platinum, brass and copper finishes. island hoods.
- Page 13 The information and images are the copyright property of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc.
- Page 14 LEFT OUTER EDGE OF HOOD...
- Page 15 Wolf Appliance Company, LLC P.O. Box 44848 • Madison, WI 53744 • 800-332-9513 www.wolfappliance.com 805050 7/03...
Need help?
Do you have a question about the I363418 and is the answer not in the manual?
Questions and answers