Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GarrettCom DynaStar DS2000-IFR
Summary of Contents for GarrettCom DynaStar DS2000-IFR
- Page 1 DynaStar 2000 Industrial Frame Router (DS2000-IFR) Installation Maintenance Guide GarrettCom, Inc. 25 Commerce Way #1 North Andover, MA 01845 Phone: 978.688.8807 Fax: 978.688.8771 Part Number: 3-01-0088-01 Rev AA $5.00 USD...
-
Page 3: Copyright
E C L A R A T I O N S O C U M E N T O T I C E C o p y r i g h t Copyright 2005 by Dymec, Inc. Printed in the US. All rights reserved. This manual may not be reproduced or disclosed in whole or in part by any means without the written consent of Dymec, Inc. -
Page 4: Warranty
ECLARATIONS Warranty A R R A N T Y DYMEC, Inc. warrants equipment manufactured by it to be free from defects in materials and workmanship for a period of one (1) year from date of shipment. If within the warranty period the purchaser discovers such item was not as warranted above and promptly notifies DYMEC, Inc. -
Page 5: Patents
ECLARATIONS Patents A T E N T S As to equipment proposed and furnished by DYMEC, Inc., DYMEC, Inc. shall defend any suit or proceeding brought against purchaser so far as based on a claim that said equipment constitutes an infringement of any patent of the United States, if notified promptly in writing and given authority, information, and assistance at DYMEC, Inc.'s expense for the defense of the claim. -
Page 6: Acta Tia/Eia Is-968A (Formerly Fcc Part 68)
ECLARATIONS Safety A C T A T I A / E I A I S - 9 6 8 A ( F o r m e r l y F C C P a r t 6 8 ) This equipment complies with ACTA TIA/EIA IS-968A rules. On the device is a label that contains, among other information, the FCC registration number for this equipment. -
Page 7: Laser Radiation And Connectors
ECLARATIONS Safety Industry Canada Warnings Avis d’Industrie Canada Notice: Avis: Before installing this equipment, users should ensure that it is Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permissible to be connected to the facilities of the local permis de le raccorder aux installations de l’entreprise locale telecommunications company. -
Page 8: Service Personnel Warning
ECLARATIONS Safety S e r v i c e P e r s o n n e l W a r n i n g The D 2000 may be AC or DC powered. Remove all power connections at the circuit panel before removing the unit. -
Page 9: Table Of Contents
A B L E O F O N T E N T S ECLARATIONS Document Notice ................................i Copyright ................................i Rights.................................i Part Number Information ..........................i Revision History ..............................i Warranty ..................................ii Limitation Of Liability..............................ii Patents ................................... iii Return Of Equipment..............................iii Compliance Notices ..............................iii FCC Part 15 .............................. - Page 10 ONTENTS HAPTER NSTALLATION Pre-Installation Requirements .......................... 2-1 2.1.1 Environmental..........................2-1 2.1.2 Rack Requirements ........................2-1 2.1.3 Power Requirements ........................2-2 2.1.4 Guidelines for Wiring and Grounding ................... 2-2 2.1.4.1 Fiber.......................... 2-2 2.1.4.2 Grounding ......................... 2-2 2.1.4.3 Facility Power......................2-2 2.1.5 Equipment Requirements.......................
-
Page 11: Preface
P R E F A C E B O U T H I S A N U A L This document provides instructions to install the DS2000-IFR hardware. This document gives a product description, specifications, detailed information on ports and pinouts, all site preparation required to install the product, complete installation procedures, power up instructions, removing and maintaining the product. -
Page 12: Related Documents
ECLARATIONS Related Documents E L A T E D O C U M E N T S The DS2000-IFR documentation is contained in two manuals. This manual is one and the other is the DS2000-IFR Administrator’s Guide. The Administrator’s Guide provides instructions to configure the DS2000-IFR in a network environment. - Page 13 HAPTER N T R O D U C T I O N This chapter contains a brief description of the physical attributes of the DS2000-IFR product and describes the LEDs, pinouts, and specifications covering the device. 1 . 1 V E R V I E W The DS2000-IFR provides connectivity to Asynchronous and Ethernet traffic for on site use and acts as a WAN access device.
-
Page 14: Chapter 1 Introduction
Introduction HAPTER Overview The DS2000-IFR serves basically two functions. The first function is to provide connectivity to Ethernet and Serial devices and the second is to provide access for these Ethernet and Serial devices over a WAN (Wide Area Network) to controlling and monitoring functions. The DS2000-IFR can also be configured to provide on-site connectivity for Ethernet and Serial devices to local Ethernet networks. -
Page 15: Specifications
Introduction HAPTER Specifications 1 . 2 P E C I F I C A T I O N S This section details the specifications covering the DS2000-IFR. 1 . 2 . 1 P h y s i c a l Height: 3.5 inches (8.9 cm) •... -
Page 16: Compliance
Introduction HAPTER Specifications 1 . 2 . 4 C o m p l i a n c e Safety UL60950 EN60950 CE Mark Industrial IEEE 1613 Emissions EN55022A, FCC Part 15A VCCI, AS/NZ-3548 Immunity EN55024-2003 EN61000-6-2 EN61000-4-2 (ESD) EN610000-4-3 (RF) EN61000-4-4 (EFT) EN61000-4-5 (Surge) EN61000-4-6 (CRF) - Page 17 Introduction HAPTER Controls and Indicators 1 . 3 C O N T R O L S A N D N D I C A T O R S This section describes the controls and indicators as well as lists the pinouts for all of the DS2000-IFR ports. 1 .
-
Page 18: Controls And Indicators
Introduction HAPTER Controls and Indicators DS2000-IFR 1 . 3 . 2 I n d i c a t o r s The DS2000-IFR has LED indicators on the front panel which provide immediate information concerning the status for the standard port connections. Status indicators are also located under the Ethernet ports on the rear of the unit. - Page 19 HAPTER Introduction Controls and Indicators Table 1-4. LEDs (Continued) LED Name/Location Condition Indication Sync/Async/ Indicates that the serial port S0 is connected to an active serial device. Indicates the serial port S0 is down Flashing Data is passing through the serial port S0 Green - indicates the console port is connected to (console port) an active local terminal...
-
Page 20: Pinouts
Introduction HAPTER Pinouts 1 . 4 I N O U T S The DS2000-IFR provides one or more of the following port types: WAN, Ethernet, Serial, and one Async port (Port 6) used for local connections to the DS2000-IFR to access the management software. The following paragraphs describe the types of connectors used and the Tables referenced with each connector type detail the pinouts for each connector type. - Page 21 HAPTER Introduction Pinouts Table 1-6. Ethernet Ports - SFP Port Signal Transmit Receive Table 1-7. RS232 - Serial Ports S01 - S16 - RJ45 Signal Request To Send (RTS) Data Set Ready (DSR) Pin 1 Pin 8 Transmit Data (TxD) Receive Data (RxD) Ground (GND) Data Terminal Ready (DTR)
- Page 22 Introduction HAPTER Pinouts Table 1-9. W1 and W2 T1/E1 Ports - RJ48 Signal T1 Receive + R1 Receive - Pin 1 Pin 8 Shield T Transmit + R Transmit - Shield Not Used Not Used Table 1-10. S0 (Sync/Async)* - RJ69 (ten pin RJ45) Signal Tx Clock Data Carrier Detect (DCD)
-
Page 23: Pre-Installation Requirements
HAPTER P R E - I N S T A L L A T I O N This chapter provides the installer with relevant information concerning the pre-installation of a DS2000-IFR. The installer should make themselves familiar with the requirements listed in this chapter prior to beginning the install to ensure no unnecessary delays occur. -
Page 24: Power Requirements
Pre-Installation HAPTER Pre-Installation Requirements 2 . 1 . 3 P o w e r R e q u i r e m e n t s One external power source is required for each DS2000-IFR. The following power is required depending on the configuration of the DS2000-IFR and whether it is configured as AC or DC. -
Page 25: Equipment Requirements
Pre-Installation HAPTER Safety and Handling 2 . 1 . 5 E q u i p m e n t R e q u i r e m e n t s The following equipment is required to completely install the DS2000-IFR: DS2000-IFR •... -
Page 26: Fiber Handling
Pre-Installation HAPTER External Connections 2 . 2 . 2 . 2 F i b e r H a n d l i n g Fiber optic cables and connectors are fragile and can be easily broken or fractured through mishandling. When handling fiber optic media, observe the following warnings: Do not strike the fiber cable with tools •... -
Page 27: Unpacking The Ds2000-Ifr
HAPTER N S T A L L A T I O N This chapter provides the necessary instruction to install the DS2000-IFR. It is assumed that the guidelines listed in the pre-installation section have been followed and the site is prepared for the installation. -
Page 28: Install Optional Ethernet Fiber Optic Sfp Ports
Installation HAPTER Unpacking The DS2000-IFR 3 . 2 . 1 I n s t a l l O p t i o n a l E t h e r n e t F i b e r O p t i c S F P P o r t s The SFPs (Small Formfactor Pluggables) are optional equipment for the DS2000-IFR and are installed in most cases in the factory. -
Page 29: Rack Mounting
Installation HAPTER Installation N S T A L L A T I O N 3 . 3 This section describes rack mounting the DS2000-IFR in a rack. The unit comes prepared to be installed in a standard 19" rack either front, rear or center rails. The mounting brackets may also be removed and rotated to support other configurations. -
Page 30: Connecting Facility Power
Installation HAPTER Connecting Facility Power 3 . 4 C O N N E C T I N G F A C I L I T Y P O W E R The DS2000-IFR comes in either high or low voltage models. The unit does not have a power on/off switch and is active when the power is connected. -
Page 31: Ac Power Connection
Installation HAPTER Connecting Facility Power 3 . 4 . 2 A C P o w e r C o n n e c t i o n For AC powered units the connections are to the Power input terminals on the rear of the DS2000-IFR as shown in Figure 3-1. -
Page 32: Connecting Network Cables
Installation HAPTER Connecting Network Cables 3 . 5 C O N N E C T I N G N E T W O R K C A B L E S There are three types of connections that can be made to the DS2000-IFR. They are WAN, Ethernet, and Serial. -
Page 33: Connecting Ethernet Cables
HAPTER Installation Connecting Network Cables 3 . 5 . 2 C o n n e c t i n g E t h e r n e t C a b l e s The Ethernet ports are standard RJ45 ports. Connect the standard Ethernet cables to the Ethernet ports as follows. -
Page 34: Connecting The Wan Cable
Installation HAPTER Connecting Network Cables CAUTION: Avoid touching the fiber optic cable tips and interiors of the optical ports. If the connector or port is not being used, dust caps should be installed. Contamination could degrade the performance of the optical connection. Dymec recommends that fiber optic connectors be cleaned after each use and optical ports be cleaned only if contamination or degradation to performance is detected. -
Page 35: Verifying Installation
HAPTER Installation Verifying Installation Ethernet RS232(DEBUG) AUX1 AUX 2 Rear Panel WAN LEDs System Front Panel LEDs Made in USA Figure 3-4. WAN Ports 3 . 6 E R I F Y I N G N S T A L L A T I O N At this point the DS2000-IFR should be completely installed in a rack or other suitable mounting location, power has been applied, all external network connections have been made, and the system is ready to be configured for data traffic. - Page 36 Installation HAPTER Verifying Installation DS2000-IFR Installation and Maintenance Guide 3 - 10...
-
Page 37: Chapter Maintenance
HAPTER A I N T E N A N C E There are no corrective repairs or preventative maintenance actions for the DS2000-IFR. The unit is designed to be replaced as a unit and there are no user repairable components in this device. There are also no requirements for servicing of this device. -
Page 38: Disconnect Network Cables
Maintenance HAPTER Packing The DS2000-IFR For Shipment 4 . 1 . 2 D i s c o n n e c t N e t w o r k C a b l e s The network connections to the DS2000-IFR may include Serial, Ethernet, and WAN cables. The order for removal is not important but it is important to note that there are active devices connected to each end of the cable. -
Page 39: Cleaning Fiber Optic Devices
Maintenance HAPTER Cleaning Fiber Optic Devices 4 . 3 L E A N I N G I B E R P T I C E V I C E S This section covers the cleaning requirements and procedures for the fiber optic cable connectors and the optical ports on theDS2000-IFR. -
Page 40: Cleaning Optical Ports
Maintenance HAPTER Cleaning Fiber Optic Devices 4 . 3 . 2 C l e a n i n g O p t i c a l P o r t s These instructions are recommended only when there is evidence of contamination or when reduced performance has been detected.
Need help?
Do you have a question about the DynaStar DS2000-IFR and is the answer not in the manual?
Questions and answers