Download Print this page

Serai MT/BZERO Manual

Electromechanical gearmotor for swing gates. oerator for swing gates up to 2m - 200kg

Advertisement

Quick Links

S
E
R
A
I
D i v i s i o n e A p r i c a n c e l l i
MT/BZERO
03.B0
OERATOR FOR SWING GATES UP TO 2m - 200Kg
MT/BZERO EN V01 F12 20170127
A5VL 40g/mq - IS MT/B0/24-E

Advertisement

loading
Need help?

Need help?

Do you have a question about the MT/BZERO and is the answer not in the manual?

Questions and answers

Summary of Contents for Serai MT/BZERO

  • Page 1 D i v i s i o n e A p r i c a n c e l l i MT/BZERO 03.B0 OERATOR FOR SWING GATES UP TO 2m - 200Kg MT/BZERO EN V01 F12 20170127 A5VL 40g/mq - IS MT/B0/24-E...
  • Page 2: General Description

    Before proceeding with the installation check that all the safety conditions are observeded in full compliance with laws rules and regulations. Unfulfilment of the below listed directions will release the SERAI srl, from any responsibility for damage caused to people or things.
  • Page 3 1C - OVERALL DIMENSIONS Front Rear bracket horizontally soldered bracket Rear bracket vertically soldered...
  • Page 4 2 - BRACKETS INSTALLATION SCHEME 2A - HOW TO USE THE GRAPH Measure "E", and draw a horizontal line on the graph at the read measure. Choose a point on the drawn line, considering the desired opening angle, suitable to the column.
  • Page 5 2B - GRAPH 90° 100° 110° A (mm) If the installation measures are not properly followed, the atomation could not work correctly. For example: - cyclical trends, and sudden accelerations, - noise from the operator, - limited opening degree or absent opening (if the operator was fixed counter-lever).
  • Page 6: Installation

    3 - INSTALLATION 3A - INTRODUCTION Read the instructions manual accurately before installing the product. The producer disclaims all responsibility for any damage or bad functioning caused by non-observance of the instructions or bad connection that may result in poor safety and functioning of the operator.
  • Page 7 4 - OPERATING THE GATE MANUALLY 4A - INTRODUCTION ! Before operating the manual release disconnect the power. Manual release of the gate was thought to open/close it manually in case of power loss or operator breakdown. 4B - MANUAL RELEASE INSTRUCTIONS (see pic.4).
  • Page 8: Electrical Connections

    5 - ELECTRICAL CONNECTIONS 5A - CONNECTING THE OPERATOR TO THE AUTOMATION CONTROL UNIT To connect the operator to the control unit proceed as follows: 01. Remove the lid of the operator as shown in pic.6. 02. Loosen the cable gland, pass the cable through it, screw its 3 wires to the terminal blocks, then tighten the gland. 03.
  • Page 9 6 - MECHANICAL STOPS ADJUSTMENT 6A - INTRODUCTION An internal mechanical stop allows to stop the gate at a pre-set position, avoiding to hit the external leaf mechanical stop. 6B - ADJUSTMENT INSTRUCTIONS INSTRUCTIONS (see pic.7): - Release the operator for manual movement (see 4B). - Loosen the screw of the supplied mechanical stop (B).
  • Page 10: Compatibilità Elettromagnetica

    S AND STANDARDS TIPO: Attuatore elettromeccanico per cancelli a battenti Type: Electromechanical gearmotor for swing gates MT/BZERO MODELLO: Model: Risulta conforme a quanto previsto dalle seguenti direttive europee: Satisfies the essential requirements of the following Directives: DIRETTIVA BASSA TENSIONE Low Voltage Directive...
  • Page 11 NOTES...
  • Page 12 WARRANTY CONDITIONS The company reserves the right to make any modification without prior notice. The conventional SERAI product warranty is valid 24 months following the issuance of the fiscal document attesting to its purchase. Services covered by the warranty are provided at the company's facilities in Legnaro (PD - ITALY) or at any one of the company's authorized Service Centres.