Kenwood TS-890S Command Reference Manual page 54

PB4
Voice Message Channel Name
1 2 3
Set
P B 4
1 2 3
Read
P B 4
1 2 3
Answer
P B 4
PB5
Voice Message Recording Sound Source
1 2 3
Set
P B 5
1 2 3
Read
P B 5
1 2 3
Answer
P B 5
PB6
Voice Message Recording Total Remaining Time
1 2 3
Read
P B 6
1 2 3
Answer
P B 6
PC
Output Power
1 2 3
Set
P C P1
1 2 3
Read
P C ;
1 2 3
Answer
P C P1
PL
Speech Processor Input/Output Level
1 2 3
Set
P L P1
1 2 3
Read
P L ;
1 2 3
Answer
P L P1
PC Control Command referenCe guide
4 5 6 ~ x
P1 P2 P3 ;
4 5 6 7 8
P1 ;
4 5 6 ~ x
P1 P2 P3 ;
4 5 6 7 8
P1 ;
4 5 6 7 8
;
4 5 6 7 8
P1 ;
4 5 6 7 8
;
4 5 6 7 8
P1 P1 P1 ;
4 5 6 7 8
P1 P1 ;
4 5 6 7 8
4 5 6 7 8
P1 P1 ;
4 5 6 7 8
P1 P1 P2 P2 P2
4 5 6 7 8
4 5 6 7 8
P1 P1 P2 P2 P2
Parameters:
P1 (Playback channel )
9 10
1: CH 1
2: CH 2
3: CH 3
9 10
4: CH 4
5: CH 5
6: CH 6
9 10
P2
Always a space
P3 (Channel name)
Up to 30 characters
• You cannot use this command while the Voice Message List
display (PB0) is OFF.
• You cannot set unregistered channels.
Parameters:
P1
9 10
0: Microphone
1: ACC 2
2: USB Audio
9 10
3: LAN
• You cannot use this command while the Voice Message List
9 10
display (PB0) is OFF.
Parameters:
P1 (Remaining time)
9 10
000 ~ 100 (sec)
• You cannot use this command while the Voice Message List
9 10
display (PB0) is OFF.
Parameters:
P1
9 10
HF/ 50 MHz band
005 ~ 100: SSB/ CW/ FM/ FSK/ PSK
005 ~ 025: AM
9 10
70 MHz band
005 ~ 050: SSB/ CW/ FM/ FSK/ PSK
005 ~ 013: AM
9 10
• The change step is 1 W or 5 W steps depending on the Menu
[6 - 04] "Transmit Power Step Size" setting.
• If the transmission output limiter function is ON, P1 cannot be
set above the limit value.
• If the Drive out function is ON, set / read for the Drive out level.
• To set 12.5 W in AM mode of 70 MHz band, P1 is set to "013".
When reading the 12.5 W state in AM mode of 70 MHz band,
P1 is 013. (E type only)
Parameters:
P1 (Input level)
9 10
000 (minimum) ~ 100 (maximum)
; P2 (Output level)
000 (minimum) ~ 100 (maximum)
9 10
9 10
;
– 53 –