Kenwood TS-890S Command Reference Manual page 68

UD
VFO Frequency UP/DOWN
1 2 3
Set 1
U D P1
1 2 3
Set 2
U D P1
UR / UT
RX / TX Equalizer
1 2 3
U R / T P1
11 12 13
P5 P5 P6
Set
21 22 23
P10 P10 P11
31 32 33
P15 P15 P16
1 2 3
Read
U R / T ;
1 2 3
U R / T P1
11 12 13
P5 P5 P6
Answer
21 22 23
P10 P10 P11
31 32 33
P15 P15 P16
VD
VOX Delay Time
1 2 3
Set
V D P1
1 2 3
Read
V D P1
1 2 3
Answer
V D P1
PC Control Command referenCe guide
4 5 6 7 8
P2 P3 P3 ;
4 5 6 7 8
P2 ;
4 5 6 7 8
P1 P2 P2 P3 P3
14 15 16 17 18
P6 P7 P7 P8 P8
24 25 26 27 28
P11 P12 P12 P13 P13
34 35 36 37 38
P16 P17 P17 P18 P18
4 5 6 7 8
4 5 6 7 8
P1 P2 P2 P3 P3
14 15 16 17 18
P6 P7 P7 P8 P8
24 25 26 27 28
P11 P12 P12 P13 P13
34 35 36 37 38
P16 P17 P17 P18 P18
4 5 6 7 8
P2 P2 P2 ;
4 5 6 7 8
;
4 5 6 7 8
P2 P2 P2 ;
Parameters:
P1 (Target VFO)
9 10
0: VFO A
1: VFO B
P2 (Frequency change direction)
9 10
0: Direction Up
1: Direction Down
P3 (Change the step number (Set 1 command only))
00~99
• The frequency change amount per step is same as the change
step by the Tuning control.
• In simplex mode, it is also valid for the VFO on the unused side.
• If you send a command in the format of setting 2 omitting
specification of the number of changing steps of parameter P3,
it will be changed in 1 step.
• You cannot be set in memory channel mode.
• You cannot be set during TF-SET
Parameters:
P1: 0 Hz level
9 10
P2: 300 Hz level
P4 P4 P3: 600 Hz level
P4: 900 Hz level
19 20
P5: 1200 Hz level
P9 P9
P6: 1500 Hz level
P7: 1800 Hz level
29 30
P8: 2100 Hz level
P14 P14
P9: 2400 Hz level
39 40
P10: 2700 Hz level
P11: 3000 Hz level
;
P12: 3300 Hz level
9 10
P13: 3600 Hz level
P14: 3900 Hz level
P15: 4200 Hz level
9 10
P16: 4500 Hz level
P4 P4
P17: 4800 Hz level
P18: 5100 Hz level
19 20
00 ~ 30: Where 00 is +6 dB, 06 is 0 dB, and 30 is -24 dB.
P9 P9
 The value is outside range will result in an error.
29 30
 An entered value of 99 for parameters P1 ~ P18 sets that
parameter to its initial value.
P14 P14
39 40
• With all the effects, the equalized contents are backed up using
this setting command.
;
Parameters:
P1 (Input type)
9 10
0: Microphone
1: ACC 2
2: USB-Audio
9 10
3: LAN
P2 (VOX Delay Time (value x 150 ms))
000 ~ 020
9 10
999: Initial value setting (setting command only)
– 67 –